I have this problem when I enable friction, if I disable it, it return to the strimmer center
I have this problem when I enable friction, if I disable it, it return to the strimmer center
PIf you read the subsequent messages above, it turned out that I didn't have a config or hw issue. I simply misunderstood the intended behavior.
IPitch forces feel softer than roll , what setting do I need to change to make them equal?
IBu the way Telem FFB introduced a virus that has been a pain in the ass to remove.
II clicked on the FFB screen on the link on the bottom left corner and that inmediatelly started the virus
NThere is no virus in TelemFFB. Hundreds of people in here are running it. The source is open on GitHub too if you want to look at it.
Windows defender and some other AV tools will sometimes flag it as a virus however. This is because it is written in Python and compiled with βpyinstallerβ which can sometimes result in certain file hashes that are often found in low tech malware that is commonly also written in Python and compiled with pyinstaller.
Windows defender and some other AV tools will sometimes flag it as a virus however. This is because it is written in Python and compiled with βpyinstallerβ which can sometimes result in certain file hashes that are often found in low tech malware that is commonly also written in Python and compiled with pyinstaller.
R@walmis after getting my adpater in place yesterday I've only now got around to testing it and I'm unable to get my WinWing F18 stick buttons working. Firmware is v1.0.16 - any suggestions?
RNot a single WinWing button is highlighting when clicked in...
1) Microsoft game controllers (which I realise I should ignore anyway)
2) The WebUSB tool
3) The RAW BTN column in the VPforce Configurator
I have grip type selected as "WinWing Adapter" but I've tried all the others as well (just to test) and nothing is working
1) Microsoft game controllers (which I realise I should ignore anyway)
2) The WebUSB tool
3) The RAW BTN column in the VPforce Configurator
I have grip type selected as "WinWing Adapter" but I've tried all the others as well (just to test) and nothing is working
RLegobirds - do you get yours working?
WSomething is not mating properly most likely, let's see which side is not talking:
1: set Generic grip debug
1: set Generic grip debug
- Open Debug Tab and check the data that it's printing
WIf the data is all FFs then the adapter is not talking to the base
R
Rlooks like that's the case then
Wmaybe it's not inserted properly, the star pattern should insert fully into the base
Ri'll double check
Rshould it "work" without the joystick head attached?
Wyeah
WI recommend holding it like this and plugging it into the socket
Rok, I've tried a couple of times and I'm pretty confident i've got it fully in place - but still reporting back all FFF
Wd'oh, before I send you a new one, can you remove bottom start piece from the adapter and check?
Ryeah, just did that as well - figured it might be blocking it going in all the way or something - no luck 
WNot sure what went wrong there, since I've tested it before shipping without issues
Rhum, rember this was the one I sent the picture of that showed the misalignmed of the bottom start piece... so not sure if this one COULD be tested in it's final form (at least not how it arrived to me?)
RI can solder fairly well... any chance I could fix it rather than you sending out a new one or is there a circuit board in there?
Ror if you DID test the adapter is there any chance it could be a problem with the base? 
any way I can check that?
any way I can check that?WDid it come out of the box like that? Or you noticed after you tried to attach it? Maybe it got mixed up with an untested one, hmm.
Ryeah, 100% came out of the red bubble wrap packet like that
Rnope, was never able to attach it - I know how fragile these connectors are so checked visually first
WRoger that
WI'll probably arrange you a new one
WYou can try to fix the existing one in the meantime
Rok amazing thank you - and yeah, I'll try and give it a look this weekend - if I get it working I'll let you know as soon as I can 
RYeah even like this Iβm getting FFF
WYou can test the internal connections by probing with a multimeter in diode test mode: put the positive(red) probe on GND go through other pins with the negative(black) one. It should read a diode (~0.5-0.7V) on all pins, otherwise it would indicate a broken internal connection.
Rha, well, only the VDD is reporting 0.62V - all the other ones don't seem to register at all - not even 0.0V
Rand ehhh yeah... no obvious soldering problems so I don't think I'm going to be able to fix it myself - wouldn't have guessed there was a whole circuit board in there! 
II downloaded the latest WIP from Nov 30th, it worked fine, the program did not install a virus.
There is a link in the window that says get help.
Virus got installed when I clicked on it.
There is a link in the window that says get help.
Virus got installed when I clicked on it.
IWhat it does it opens browsers in all of them with get help pages non stop.
IThat get help link its on the lower left hand corner.
WI don't recall any "get help" links anywhere in our apps.
II am still trying to fix the virus in my PC , its the latest WIP file from Nov 30th
WThis doesn't make sense
IAre you using that version of Telem FFB?
IIt had blue letters on lower left corner that said get help
NThe last version of TelemFFB was built on November 24th
Nno such text exists in TelemFFB... Are you talking about the documentation link?
INo its the window when I am playing DCS and tells the plane I am flying and all the info for the effects
I
IThat is the version I downloaded yesterday
N11/30 is the date you downloaded it.. not the date it was built.
But I am telling you , there is no "Get Help" button anywhere in TelemFFB. The only blue button anywhere in the lower left corner of TelemFFB is the documentation link I screenshotted above... all that does is open a browser to the google docs version of the documentation...
But I am telling you , there is no "Get Help" button anywhere in TelemFFB. The only blue button anywhere in the lower left corner of TelemFFB is the documentation link I screenshotted above... all that does is open a browser to the google docs version of the documentation...
Nthat right there is the entirety of what that link does