@bounty_v How did you guys handle the pedal situation?
@bounty_v How did you guys handle the pedal situation?
Ftwo mounting plates
MOnce I actually do it, I'm going to get a second pedal plate/bar for the racing setup.
NAnd just change them out by hand when needed?
Jif you search messages from me that contain images I have shared some pics of different iterations of my build, might give you an idea idk
JI plan to invert my racing pedals and raise them higher than they currently are (I have rudder pedals mounted on a frame I added to the bottom of my cockpit underneath the racing pedals, then I just slide the racing pedal plate backwards to use them) so that I have access to both at once, but since it is entirely DIY with no real reference I'll basically need to get every part cut to custom lengths and figure out every piece I need.
I also plan to modify left cockpit arm that will mount my throttle and control panel into a door so I can open and close that for easier access to sitting down.
Lastly, I plan to diy some sort of floor shroud around my center mounted Rhino base so I don't accidently hit it with my shoes getting in and out
I also plan to modify left cockpit arm that will mount my throttle and control panel into a door so I can open and close that for easier access to sitting down.
Lastly, I plan to diy some sort of floor shroud around my center mounted Rhino base so I don't accidently hit it with my shoes getting in and out
JSince all of that will end up being a decent amount of money ($200+) I'm waiting until after April to pull the trigger
NI wonder if it's possible to construct some sort of sliding system to change the pedal sets easily, but it may be more inconvenient than not
JThere's someone who figured that out it's just more DIY than I personally have the capacity to accomplish
Jthey built 2 pedal mounts and held them in place with magnets etc.
Jwas discussed in this server you can probably find the video
NHow tall is the Rhino with no grip? Would it be uncomfortable to have in place when using a wheel?
J#
faq
faqJhas the specs
SI mean it depends entierly on where and how you moun it?
HHas anyone tried attaching heat sinks to the motor to slow down the motor's warming-up speed?
VAnyone here with a Next Level Racing Military Seat?I just received it, and I am collecting ideas for mounting the Rhino in it. I would prefer to mount the Rhino without extensions
V
RHINO #0320 Has Shipped!
DI just installed mine in my rig that I received for Christmas. I will be following to see what suggestions people have. I am planning on mounting mine to my QR4Rigs mount, the same one I am using for my Virpil CM3 base... hoping that works.
LCan you drill a hole here and attach a base plate large enough for a 
? I know, it looks too small to be stable but I don't see any other way to mount a Rhino into this rig right away. Not without making several new parts out of wood or metal.
? I know, it looks too small to be stable but I don't see any other way to mount a Rhino into this rig right away. Not without making several new parts out of wood or metal.
TI'd design and 3D print a mount Fourgrinder. Is that not an option for you? My rig is different from yours and an easier problem but that's what I did for mine.
DThe QR4Rigs mounts are printed... pretty sturdy. I plan to use that.
SWhat was the wait time? I put in a pre order a few weeks ago. I'm looking forward to getting this puppy setup
I!stats
VHey @indifferentbadger,
So the last Shipped RHINO is #0320 on 2023-12-27
Average waiting time from preorder to shipped is 214 days, median is 227 days, max is 379 days
314 Rhinos are shipped in total
So the last Shipped RHINO is #0320 on 2023-12-27
Average waiting time from preorder to shipped is 214 days, median is 227 days, max is 379 days
314 Rhinos are shipped in total
I@anythingbutswan 
fairly accurate numbers.
fairly accurate numbers.Sokay.... LOL
DGot me this on the boxing day sale
D@pinksht they are in sale at JB
Poh nive I'll check it out, decent sale?
DI had a similar problem with my DOF Reality H6 motion platform, very tight on space in front of the seat as well.
I wanted the Rhino to be easily swapped out and I alsi wanted to be able to climb aboard without struggling to lift my leg over it. So I use a large flat plate that swivels in one corner. It's easily moved into place and yet holds the base very firmly. Q4Rigs plates weren't around when I was looking for ways to quick change my other controls so I use powerful neodym magnets instead. They attach like limpet mines and have just enough grip to be firmly held, yet are easily detached with a firm twist to one side.
Here's a short video of me climbing aboard my H6, and then lening forward to swivel the plate round after my legs are in place.
https://youtu.be/IKqij8tS_Lo
I wanted the Rhino to be easily swapped out and I alsi wanted to be able to climb aboard without struggling to lift my leg over it. So I use a large flat plate that swivels in one corner. It's easily moved into place and yet holds the base very firmly. Q4Rigs plates weren't around when I was looking for ways to quick change my other controls so I use powerful neodym magnets instead. They attach like limpet mines and have just enough grip to be firmly held, yet are easily detached with a firm twist to one side.
Here's a short video of me climbing aboard my H6, and then lening forward to swivel the plate round after my legs are in place.
https://youtu.be/IKqij8tS_Lo
DYeah, wasnt too bad
V 
RHINO #0321 Has Shipped!
B
hmm it finally updated on tracking, but the email suggests delivery on Friday the 22/12. I doubt that will work out for them.
Ashould be fine, that just means you'll have to wait about a year
BNah they even specified 2023
BGuess I'll have to wait until the universe restarts and comes back around
WThe UPS tracking lags a bit because our carrier delivers the packages to UPS Poland first (that takes a couple of business days, hence no UPS tracking the first couple of days) plus the Christmas holidays lagged things even more lol
BThat's what I assumed as well
I just marvel at ups' confidence they can time travel is all.
Certainly can't fault you, i got the availability notice, payment, and shipping notification with tracking number in less than eight hours.
My guess you got it out half an hour before everyone took off for christmas.
I just marvel at ups' confidence they can time travel is all.
Certainly can't fault you, i got the availability notice, payment, and shipping notification with tracking number in less than eight hours.
My guess you got it out half an hour before everyone took off for christmas.
WYeah that's about right 
BAt least hope you and yours have had a happy holiday 
WThanks, had a bit of R&R during Christmas weekend. Hope yours was great too!
JActually really enjoy mine. Get SimShaker for Aviators (free) while you're at it.
Vnice..is it sturdy enough?
VThat plate is you highlitghed is too low, and you would not have the space to mount the rhino (it would be obstructed by the keyboard tray and by the central arm).
What I plan to do is to mount that central arm lower (to the next holes) and use a 3d printed plate which attaches directly to it.
I found this one on the internet...it's for the winwing orion 2....
https://www.printables.com/model/636215-joystick-adapter-for-next-level-racing-flight-simu
maybe someone with the skills can design a larger one for the rhino
or the same can be adapted some way. A wooden base with the same dimensions of the Rhino lower base can be screwed to it.
The alternative is to don't mount the central arm...and floor mount the rhino with a large wooden base.
It would not be optimal for me as I don't want to use extensions...but it could be a solution
What I plan to do is to mount that central arm lower (to the next holes) and use a 3d printed plate which attaches directly to it.
I found this one on the internet...it's for the winwing orion 2....
https://www.printables.com/model/636215-joystick-adapter-for-next-level-racing-flight-simu
maybe someone with the skills can design a larger one for the rhino
or the same can be adapted some way. A wooden base with the same dimensions of the Rhino lower base can be screwed to it.
The alternative is to don't mount the central arm...and floor mount the rhino with a large wooden base.
It would not be optimal for me as I don't want to use extensions...but it could be a solution
LThat's what I did, I took an MDF base plate of 55 x 90 cm, some 2 by 4 and an Ikea chair (which Buttkicker broke already 
). But if you can lower the round plate low enough, I'd try attaching base plate to that first 
). But if you can lower the round plate low enough, I'd try attaching base plate to that first Ahttps://youtu.be/BUxMyIdAb6Q?feature=shared
This could be a nice base for a FFB Yoke. At 13:30 min. you can see the inside.
This could be a nice base for a FFB Yoke. At 13:30 min. you can see the inside.
YouTubeRuss Barlow
A detailed review of the features and performance of the new SmartFly Yoke from Ray Dynamics in India. Similar to the Yoko+ in many ways but at a fraction of the cost could this be for you? See it in action and hear my pros and cons before a final recommendation.
ACosts 399$ without Tax, shipping, etc.
SI preorded mine in may of this year, so what 7ish months?
SHonestly way less than I thought it would be. I trully wasn't expeting it till next year
SAnd now the bottleneck to playing with it is lack of mount lol. Never thought monstertec would be the delay here