Anyone encounter an issue when using teleFFB your jet seat doesn’t behave like it should?
Anyone encounter an issue when using teleFFB your jet seat doesn’t behave like it should?
DI have both and have had no issues using both SimShaker Wings and Aviator while using teleFFB for various games.
R@walmis I'm not getting any button data from my Wingwing Grip. Winwing Adapter is selected and sent. As this is a DIY project. I have checked and double check the pinout, and made sure that I have continuity on all pins. Everthing else is working great. Any Thoughts?
SIs there any chance that TelemFFB could someday take over the job of SimShaker Wings and Sound Module? Would be nice to unify effects and have one less program running.
Nnot likely. Those shaker apps generate sound waves over an analog audio cable that excite the transducers to approximate vibrations/rumbles/thuds, etc.. TelemFFB is talking directly to the motor control board using an API to cause the motors to 'vibrate' at certain (or multiple) frequencies, directions and intensities.
SRetightened the belt today, and I think I found out why it was loose. When I loosened the bolts I noticed that the top-right and bottom-left bolt (as seen when looking at the left side of the base) had almost no resistance and were loose. After adjusting the belt and motor position, when I started to tighten them there is almost no resistance, so I guess they are stripped or something? The two other bolts are normal and tighten snug as expected. Is there a way to fix this? With only two bolts holding the motor in place I guess it will slip over time again…
3Try to up date Telem but it just shuts down and never starts back up?
NIf nothing happens when TelemFFB exits to do the update, something is prohibiting the updater app from launching.
In fact, the updater app should actually launch just before TelemFFB exits.
In fact, the updater app should actually launch just before TelemFFB exits.
3I ended up clicking on the file at the bottom left. Then downloaded and unzipped it to get updated app.
3Just tried the update and it was very stable!! Worked well
DFor IL2 or DCS? 2 different issues can occur trying to get it all to work at the same time + butt kicker i have resolved them all ping me if you need help.
DI currently use a .bat file to call all my programs sequentially one after another, i suggest you do the same
CHas anyone had issues with the Vkb adapter? I can't seem to get mine to work, the grip is not being detected by my blackbox.
PWhat is the correct way to 'stiffen up' the stick in the center of the axis a bit more? Like if I wanted to make the stick feel almost as stiff through the whole axis as it would be at the end. I'm trying to play with the spring force gain map but I get instability when I move the gain up more in the center of the axis. I can send screen shots of my settings & what the gain map looks like when I try? Any help is great as always, cheers
Athe adapter is very simple, just a pass through cable
AI don't know of anything besides trying the basic things like different usb ports and so on
WUgh, yeah probably stripped aluminum thread. It's possible to remedy this by using a M6 nuts in addition to motor threads. DM me for details if needed.
WYeah, the adapter is a simple passthrough cable. Can you do basic troubleshooting like checking for continuity for the contacts? I can send the pinout for the VKB.
CI can give it a try, I'm not very technically skilled but willing to try.
TDoes someone has a standard profile for MSFS 2020?
Sive done this, play with the dampening LPF frequency, raise it 1 at a time, apply, give the stick a pluck to see if it goes crazy, eventually it will be fine
RDcs
DFor DCS look in export.lua in your saved games settings ... there is HF8 software(im assuming you're using HF8 here) that tries to override or compete with SSA (sim shaker aviators if you have that) you basically need to comment one out by using -- and use either one or the other.
DAs for telemFFB there is a part of the export.lua in there as well. It shouldnt conflict, if it does try switching which gets executed first by putting it above or below where your shaker seat is being triggered in export.lua
DHello everybody. I have a little issue. When flying the apache in dcs and using the force trim button the joystick stays in that position. However on the in game overlay i can see that the joystick is moving back (50% of the way between center point and trim set, you can feel it also in on the stick that its moving back a tiny bit). that results in a pitch up again, when trying to trim nose down. Tried the in game special settings for FFB but no differents at all. do i have to change something in the rhino software?
SCan you post that bat file? It's been 30 years since I've made one and I don't remember the syntax
AAre you using curves on the cyclic axes in DCS? They don't play nice with FFB, and cause the kind of issues you describe.
Dyes i do a curve of 20 in pitch and roll
Dwithout its perfect. thanks for the help!
THi Boffins. My pedals keep throwing this up. I've been swapping USB ports but no change. They reset themselves as the joystick. Getting a bit boring, any ideas?
T
T
T
NIf you are pushing vpconf profiles via TelemFFB, make sure the profile is for the right PID, or it will overwrite what’s on the device currently.
TOK, so it just did it again, when TelemFFB did a push. Would you suggest I delete my pedal configs and start again to make sure? Looked in the pedal config file and can't see actual PID number, but the serial look correct.
TMSFS_Pedals_Plane.vpconf6.52KB
Nin that file:
decimal 8275 = 0x2053
I assume 2053 is the correct PID for your pedals. Check the logs and make sure it is loading the file you think it is.. look for a line like this in the logs:
decimal 8275 = 0x2053
I assume 2053 is the correct PID for your pedals. Check the logs and make sure it is loading the file you think it is.. look for a line like this in the logs:
TYes that is the PID, I'll check it, thank you.
TOK, seems to be under control now, I must have corrupted something. Thanks again.
DDamn didnt see this next time do an @unclestains on my name and itll ping me I think.
DYea dude you know I've been thinking... A lot of people might get use of this ill create a github with this and post. Remind me if I haven't responded in like a week.
D
Dexample .bat file, you start as a .txt and then when you create it change it to .bat ... this is then an executable.
If you want to edit it later, use notepad++ to edit.
If you want to edit it later, use notepad++ to edit.
RWould buy in a heartbeat ngl, if software supports it well
Sfyi you dont have to keep vpf configurator open, or openxr toolkit either
GHopefully somebody can help, I am trying to update the firmware on my rhino via the web app at https://vpforce.eu/usb/rhino/ but when I try to connect, the app searches for the rhino indefinitely and never finds it. Any idea why?
JHave you tried swapping ports and rebooting?
GOK I will try and report back thanks for the suggestion
BFrom what I gathered this also require a chromium browser, so for simplicity sake just use chrome to do it.
Firefox is not supported at all.
Firefox is not supported at all.
GI am using chrome ,and changing usb port made the web app able to recognise the rhino base, so now my rhino is connected but when I hit the update firmware tab I get this error.... NetworkError:Failed to execute 'ClaimInterface' on 'USBDevice': Unable to claim Interface.