RYou mean the seat pan? Yes, it's covered with that black fabric. That's glued in, so it's a little anoying if you are drilling through it (drill bits will bind and may even break).
Pahh ok, can hopefully cut the material & use glue to stop it threading apart, or if it's the right type of material can burn a small hole for drill
Phopefully I can undo the black material from the seat pan, cut the cut out a bit bigger then re-glue the fabric in place
P& did I understand correct that the seat cushion cover comes off?
RI built my own gimbal. The extension is just enough so that the grip clears my thighs.
Pie. the green & black cover on the seat
RYes the cushion cover is velcroed it comes right off.
Poh you cut it out so the whole rhino base fits in? ok, my rhino will still be 'floor' mounted & only the extension coming up to the cut out
PI see the velcro on the seat pan material for the seat cushion, but sorry to ask again just to be sure the actual cover material on the seat cushion itself, does that come off to reveal the foam underneath? sry to ask again just wana be clear
Plikely ordering things tomorow morning
RHere is how it’s mounted. My gimbals size is smaller than the rhino and the way I had it mounted I didn’t have to cut the steel seat pan, just the cushion. YMMV
RYep it’s right off.
Pperfect thanks m8
Palmost like it was made for us do cut it larger
Pthey should of made the cut out in the seat pan over sized for that reason too
Pok I think I've got the best idea about that seat I'll get without it here, cheer for all the help m8
P
Pplaning on getting that pit; TR160, the green marking was me trying to show my m8 how I'll make an adjustable Rhino mount
Pon the inside walls put some 160x40 profile mounted vertically then between them a 160x40 'laying flat', that should give adjustments in both directions horizontal & vertical
Pthat pit, plus the nlr seat & hf8
PI need to talk to pagani tomorrow & ask about the specs for the seat mounts
RYeah, if you don't have any hang ups on modding it as soon as you get it, it's really not a difficult task as long as you have some basic tools
PI'd say it'd be different to how your's does as it's the standalone version
Preally considering taking the foam base to a foam & rubber shop & getting it cut for the hf8 & a gel/mem foam topper, I don't have any meat on my arse lol
Rhaha it's really not that difficult. I got a turkey cutter knife, and it went through the foam quite easily.
Phow far back does it recline? enough for laying back a bit?
RIt reclines quite a bit, you don't have ot worry about that.
Ror do you mean slide back? it slides about 5-6 inches
Poh yeah, just to make the cut out bigger I'll diy with a big bread knife, but I may go as far as the mem foam/hf8 cut out mod, I have heard ppl say the jetseat/hf8 can get a bit sore after a while
Pyeah I meant how far will it recline back, gotta be able to lay back after a flight & watch YT lol
Pdid you diy that f16 throttle grip & base?
Rit will recline up to 122 degrees
Ryep
Pvery nice, did you do any type of "lifting the grip" detent system
Ryeah, it has the lift the grip syste, it's reversed, underneath the grip instead.
Pfar out m8 that really cool, good job
RRActually you can recline it flat. lol
Pok going to get a small mattress made for it now 
PI can just sleep at my pit
Pcheers for all the help m8, I'm off to bed
RNo problem! Good night!
DIs there a way to invert the trim hat when using DCS? I had to invert the installation of the box… the X and Y axis work just fine. The trim hat works, however it seems to trim in the opposite direction. When I trim nose up, the stick trims down and vice versa.
AIIRC there is a FFB tune menu in DCS controls/axes screen. Try inverting the FFB there.
DTried that…. Did not seem to help the trim.
WWhich aircraft?
LHi everyone, sorry of this has been asked before, couldn’t find it.
Weirdly, I can’t get the stick to center (see images) and I bet it’s software related, so I’m just too dumb to fix it. Can any of you guys help me out here how I can get it centered?
I’ve been needing to add huge deadzones to my dcs y axes so the aircraft don’t constantly pull up.
Weirdly, I can’t get the stick to center (see images) and I bet it’s software related, so I’m just too dumb to fix it. Can any of you guys help me out here how I can get it centered?
I’ve been needing to add huge deadzones to my dcs y axes so the aircraft don’t constantly pull up.
LThanks @walmis ! I'll give it a go
DThe F-15E.