Yeah, you can definitely use the order form to order spare parts
Yeah, you can definitely use the order form to order spare parts
Phey m8 any idea what would be causing the center to jump to the side like this? So far I've only noticed this only happens when I load the Kiowa?
Pjust loaded a training mission & it jumped to the side from centre
Phttps://discord.com/channels/965234441511383080/968208779084701716/1250340358663966863see there it's center
Discord
Discord is great for playing games and chilling with friends, or even building a worldwide community. Customize your own space to talk, play, and hang out.
BMaybe it starts off with a trimmed position?
Poh this has started in the air 
Pthank you
BDon't know for sure, but that's my first guess.
Pit likely is. I'll confirm in a min
WYes, the Sim/application drives the center position
OHas anyone managed to replace the fan with a quieter one (like a Noctua). Or if not can you share any details of what spec fan (size and plug) I should be looking for?
WI'll add provisions to the new firmware to adjust the fan settings to make them more quieter 
Nso... who's going to be first to seal all the joints on their rhino and then fill her up with actively cooled mineral oil?
OWould it have any implications for heat/life?
OThats why I was leaning towards upgrading the fan - to ensure airflow would stay the same but noise should come down
OI wouldn't want to just turn the fan speed down to make it quieter and then find its causing problems with component heat and life
Wnah, it won't cause any issues since motors have thermal management built in. But anyway the fan specs are: 60x60x10, 12V
Ohttps://www.amazon.com/WINSINN-Bearings-Brushless-Cooling-60mm10mm/dp/B08R9JNB2Y
Like this? And would 2 pin be ok?
Like this? And would 2 pin be ok?
WINSINN DC 60mm Fan 12V 6010 Dual Ball Bearing Brushless Cooling 60mmx10mm 2PIN (Pack of 2Pcs)
OIn any case I'll probably wait for your firmware update first and see how that goes but doesn't hurt to do a bit of research in the meantime
WThose won't be any quieter I reckon
OHmmm ok
OIt looks like the "good" quiet options are 60x60x25 (noctua and coolermaster)
Othat definately wont fit right?
WIt would fit in the front, but in the rear it would need to stick outside the case.
OI'll wait for your firmware update then and see how things are after that
FI have some issues:
(1) the stick vibrates when neither the Config or TelemFFB apps are running
(2) the gain pot on the base isn't working
(3) the force is odd and not responding to adjustments in the config app.
I've restarted Windows, checked for firmware updates, I'm applying the changes. It's my first day with the Rhino, so I may be doing something wrong, but it all looks strange. Any ideas?
(1) the stick vibrates when neither the Config or TelemFFB apps are running
(2) the gain pot on the base isn't working
(3) the force is odd and not responding to adjustments in the config app.
I've restarted Windows, checked for firmware updates, I'm applying the changes. It's my first day with the Rhino, so I may be doing something wrong, but it all looks strange. Any ideas?
N1.) Vibrating? Or oscillating? If its oscillating, thats likely caused by too high gain on friction/damper or having the spring mapping pulled in too tight. If its actually vibrating (like an engine rumble), it could be a stuck effect. Look in the debug tab of the configurator software to see what effects are active ("Loaded Effects" pane on the right side of the page). Square/Sine/Triangle/Sawtooth are periodic (vibration) type effects.
2.) How is the pot configured in the configurator software? You can connect the pot to any of the sliders, but its probably set to "none" by default
3.) not sure I understand. Can you elaborate?
2.) How is the pot configured in the configurator software? You can connect the pot to any of the sliders, but its probably set to "none" by default
3.) not sure I understand. Can you elaborate?
BIs there a way to set a button on my winwing Orion throttle to control the hardware force trim for the rhino joystick. Another words, turn a knob on my throttle to pitch nose up or down instead of a button on my joystick?
PCheck out the VPforce Loopback app, it may be able to do this, you would probably need hid hide too??
BRecently i'm noticing my X-Axis being offset a few percent, using Protomakers DIY base, Virpil 20cm extension + Constellation Alpha grip. I guess it's caused by the rather long extension + heavy grip? Whatever i set in the balance spring, i can't get it to properly center without using adaptive recentering.
Even if i rotate the grip bringing the brake handle over to the right side, it still feels like there is a bias pulling the stick to the left, away from center. Any idea whats wrong?
Even if i rotate the grip bringing the brake handle over to the right side, it still feels like there is a bias pulling the stick to the left, away from center. Any idea whats wrong?
KNew calibration?
WTry adding some static force to the Right
Wmaybe there's some misalignment in the gimbal causing some force to the left
BAutocalibrate didn't solve it
BCompletely forgot about the static force effect.. thanks Could be the gimbal, i did notice odd sounds from time to time, guess i'll have to take it all apart again at some point.
Could be the gimbal, i did notice odd sounds from time to time, guess i'll have to take it all apart again at some point.
I@walmis @Number481 There is an issue in IL2 where we cannot get full elevator with the Rhino, this picture is with the stick pulled all the way back, VPforce default configuration. How can I full elevator deflection with the Rhino? which settings do I need to change?
I
ISame problem with aileron
I
IIn case of roll, if I increease dead zone edgeto 96% I get full aileron
I
IBut for pitch , even Dead Zone edge at 100% I do not get full pitch control
I
NI mean, as far as IL2 is concerned, its just an axis. The fact that it is FFB capable is irrelevant here. You should look at the real-time axis graph and the X/Y data in the Configurator app. I suspect that you will find your axes are not going to +/-4096 with full deflection and you probably need to recalibrate.
WPost a screenshot of your settings tab
IRecalibration solved the issue , thank you
FThanks. I found out it was the friction setting causing the vibration. It sounds odd to me, but I guess I need to learn how the thing works. The pot had also been reset to nothing, after I reset the whole setup. I assumed it defaulted to master gain.
Nif you import the rhino defaults from the configs folder in the configurator director (which I recommend just to base-line the 'expert settings'), I believe it resets to spring gain. If you did a "reset config" that wipes out everything to firmware defaults as if you were starting from scratch configuring the expert settings on a DIY type device.
FYup, I did the reset config. This explains a lot. Thanks again!
AThis can also happen if spring forces are turned up higher, but this applies to all games tho, not IL2 specific. There’s force compensation or calibrating with some extra buffer on each end of the axis
I@Number481 Updated to the latest Telem and now I don't get any effects, I remember I had this problem before and you made a developer version for me that fixed it, no idea what the issue might be