ADone. Thank you.
NIMHO, even with regular sprung joysticks, curves are not the right solution to twitchy aircraft. Saturation works better. Unfortunately the saturation settings in DCS are also not compatible with FFB.
We have axis scaling in configurator, but it only allows for a positive saturation such that partial physical trave = full reported travel. It would also be useful to have negative capabilities such that full physical travel = partial reported travel.
You can accomplish this by manually increasing the calibrated range of the axis, but it would be nice to have a purpose built setting in configurator for doing so.
We have axis scaling in configurator, but it only allows for a positive saturation such that partial physical trave = full reported travel. It would also be useful to have negative capabilities such that full physical travel = partial reported travel.
You can accomplish this by manually increasing the calibrated range of the axis, but it would be nice to have a purpose built setting in configurator for doing so.
AAmazing service mate, thank you.
KI've found a workaround which make me happy until we found a better way.
I've described it here: https://discord.com/channels/965234441511383080/1098318539426889799/1258810327747924130
Maybe it is useful for other Hog drivers, too.
I've described it here: https://discord.com/channels/965234441511383080/1098318539426889799/1258810327747924130
Maybe it is useful for other Hog drivers, too.
KBut I think it should be useful to place a tip in the manual to disable curvatures in DCS for A-10C & Ka-50 (and probably other chopper with trimmer).
SI have mostly found creaking to be due to loose main gimbal bearings. Check all the retainers for tightness.
Dwhat does it want from me? 
SI get that message when I turn on my computer, but my Rhino isn't connected at the USB. Start there
SWait, did you already get and build your kit?
DYep
DManaged to take care of this message but didnt get much further lol
SUSB and power plugged in?
SStick beeped when you powered it?
DYep, its beeping at me
DI need to put the belts on and need that ~2000 motor position and no idea where to find it. also i am pretty sure only one motor is currently active
SYou'll find it in the Rhino config software, not TelemFFB. I think it's labeled raw_y and raw_x
SBeyond that I'll have to defer to the other green names in here
Dboth have nothing except -
Dpot_1 and 2 are working and the big red button
Dum nope. Motor X: OK Motor Y: Offline
HDouble checked the wiring?
DYep. only one green lamp thats MOT2
Hhmm… it sucks, but I guess you have to check all connections again.
RI’ve adjusted saturation, not curves in dcs and had no issues with rhino or teleffb. What doesn’t work about it ?
AI imagine curves could only be something done in telemffb or the configurator, at the firmware/hardware level before it reaches DCS
Nsame thing that happens with curves. The scaled axis position is not translated to FFB center offset so when you release the force trim button, the axis jumps to the scaled equivalent of where you let go.
Might not be apparent with fixed wing.
Might not be apparent with fixed wing.
RI havent had this issue at all with my rhino or software, using in game ffb or force hardware override. I only fly helicopters. Very weird.
Rright now I ve got the uh60 at 70 y saturation, so the physical stick doesnt move to 100% deflection to get the ingame stick to move to 100%.
RI ve got the oh58 using 90%
Rno curves are used at all, as that does mess with things in my experience
NHardware trim doesn't count since there is no physical relationship between the trimmed position and the in-game axis position. You might not notice it at %90, but try Y saturation at %50, you will see what I mean
Rok, will do. Thanks homie
Nas in pillow block bearings? 6808 bearing retainers? Or the flanged bearings
SNo. The big bearings on the end of the gimbals
SYou get it working?
DI did, upper 2 connectors seem to be dead so I put both motors into the bottom ones. Got the belts onto it and now need to finish it up, close it off etc. but thats happening tomorrow
SNice!!
HDoes anyone know how to conclusively kill the microsoft edge pop-up for the detected joystick?
SWould love to just remove Edge....
S@walmis Looks like a malicious link https://discord.com/channels/965234441511383080/968208779084701716/1259149465391206421
PObviously no one touch the "gift card" link above 
Chello, rhino is completely unresponsive, tapped the cables ever so lightly, now it wont turn on at all. i have rebooted my computer and reseated the connectors both usb and power.
Cit makes none of the normal beeps, and pressing in and out the red button also does nothing
WSince the control board is powered via USB, check the usual troubleshooting steps: try different USB ports, try a different USB-B cable
CHi sorry it appears the cable has gone bad luckily had a replacement thank you
SHi all, just recently completed my DIY rhino build and I am experiencing an issue where the X axis (roll) motor seems to be having some "hard" spots where it feels like it is overcoming a huge bump. I tested with the belt removed and turning the pulley by hand and the problem persists. The Y axis (pitch) motor does not have this problem. Any ideas? I hope it's something I can fix and not that the motor is defective.
SIt has these hard spots both when powered on and when powered off it seems.
WIs it the big motors or the 57 ones?