as in pillow block bearings? 6808 bearing retainers? Or the flanged bearings
as in pillow block bearings? 6808 bearing retainers? Or the flanged bearings
SNo. The big bearings on the end of the gimbals
SYou get it working?
DI did, upper 2 connectors seem to be dead so I put both motors into the bottom ones. Got the belts onto it and now need to finish it up, close it off etc. but thats happening tomorrow
SNice!!
HDoes anyone know how to conclusively kill the microsoft edge pop-up for the detected joystick?
SWould love to just remove Edge....
S@walmis Looks like a malicious link https://discord.com/channels/965234441511383080/968208779084701716/1259149465391206421
PObviously no one touch the "gift card" link above 
Chello, rhino is completely unresponsive, tapped the cables ever so lightly, now it wont turn on at all. i have rebooted my computer and reseated the connectors both usb and power.
Cit makes none of the normal beeps, and pressing in and out the red button also does nothing
WSince the control board is powered via USB, check the usual troubleshooting steps: try different USB ports, try a different USB-B cable
CHi sorry it appears the cable has gone bad luckily had a replacement thank you
SHi all, just recently completed my DIY rhino build and I am experiencing an issue where the X axis (roll) motor seems to be having some "hard" spots where it feels like it is overcoming a huge bump. I tested with the belt removed and turning the pulley by hand and the problem persists. The Y axis (pitch) motor does not have this problem. Any ideas? I hope it's something I can fix and not that the motor is defective.
SIt has these hard spots both when powered on and when powered off it seems.
WIs it the big motors or the 57 ones?
SIt’s the 57s
WThat's strange, I'll DM you
SHappy to report the problem is resolved! Shoutout to walmis for the fastest and best customer service I've ever received!
HWhat was it?
SThe affected motor needed to be spun up and recalibrated
SWalmis was able to do it remotely which was great!
HAwesome! Thanks.
DHi, I am having some issues today. The motors show as being offline usb shows connected.
DI can connect via the website. Firm ware is up to date. The emergency stop is not engaged.
DHave unplugged and replugged both power and usb. I do get the beeps but no connecton to the motors
DAny help in troubleshooting would be appreciated.
DIt also shows up under devices and printers as working properly
Dupdate: unplugged usb and replugged...seems to e working again.....lol
SThe ole reliable unplug and plug back in method!
Nso you were able to feel the "bump" on the motor pulley itself, when energized and with master gain up?
SYes. It became less noticeable at higher gains but it was there.
Nhow did you do the recalibration process? is it the normal auto calibration process
SI didn’t do it myself, walmis did it through Remote Desktop. Took less than 15 minutes
SIt was calibrating the anti cogging of the motor itself
SBut I don’t think the software is something that we have access to as end users
A
RWhat is the best material to print limiters in since they will be getting contact with the gimbal extension?
P@walmis are you there? can you merge my order? if is not possible just ship it
HI would recommend PETG for the limiter.
HIt is more elastic than PLA and less brittle
FCan I do anti-cogging calibration by myself?
FAs I asked before I could feel minute bump in y axis center and its suspected anti-cogging related
CHello all, I just received unit 605. I can't seem to figure this out , my VP Force is detecting telemetry fine from DCS and MSFS but XP12 isn't showing up. Do I need to turn on telemetry export in xp12 somewhere? I was in F15 squadrons from 1995 to 2002. I can't explain how close this ffb is to the real jet.
Thank you for any help
Thank you for any help
C@walmis this piece of kit is amazing , see my comment above
RWhat about abs reinforced with carbon fiber
RMay be overkill but it’s free for me
BFedEx/US customs is requesting a description for the package to understand its contents.
Should I submit the description myself or is it better for @walmis to do so?
Sorry if this isn’t the right channel for this.
Should I submit the description myself or is it better for @walmis to do so?
Sorry if this isn’t the right channel for this.
HAbrasive material on the throw limiter is counter productive. And total overkill on cost and print complexity. I wouldn't do that. I'd rather go with simple PLA if you don't have PETG laying around.
Sthis is what worked for me
