you need to disable the y axis in configurator in order for it to be recognized as a single motor se
you need to disable the y axis in configurator in order for it to be recognized as a single motor setup.
GMy emergency stop button has stopped working again, is it a logic switch or does it actually cut the power? Just wondering if I can do the same in telemffb rather than stripping it all down for the third time?
HThe „emergency“ switch is a real switch that cuts the power physically.
JThank you, that did the trick 
GAhh ok, in that case I guess I'll need a new one as it's done this 3 times now.
Thanks
Thanks
Vanybody fly the f-5? and maybe can help with setting up the vpforce
KI just turn on FFB in DCS and use that. No telmffb and no VPForce configurator open. And that works good enough for me.
Vcan you trim enough down so u have force on the stick'
KNot sure what you mean with force on the stick? Do you mean that its loose when you trim it far enough down?
Vi mean that when u let the stick go the plane goes down
KI haven't tried that much of down trim. Only enough for level flight but I did notice that to achieve level flight my trim was mostly nose down.
KSo the stick was forward over the center. I don't even know if that's realistic. Never paid much attention to stick position.
Vyeah thats the issue i have the stick being forward of the center
Vme and a friend asked a real pilot and he say normally the stick doesnt move atleast in the swiss air force one
KMight be a dcs thing. Cause when you use a non ffb stick and you trim it the stick moves in game
Hprobably loose connectors. You can tighten them with pliers (after disassembly)
KAnd I think DCSs ffb just mimics that
Vyeah thats for sure i will do some research then
HThat is perfectly normal for any aircraft that isn’t real fly by wire. For level flight at cruise speeds and higher the trim is nose down/stick forward. The faster you go the more the wings want to pitch up, so you have to counter that with trim.
Tmy computer always has this icon when my base is plugged in is this normal? Is there something I need to do in order to get this to go away?
RIs there a setting to keep it from chirping?
![Prometheus [Prom]](https://cdn.discordapp.com/avatars/777496628579401739/90d1e9e0a05c7bafd59a74ba942bd870.webp?size=40)
Pthat just means you have a usb device connected, shouldn’t be an issue. It’s usually used to click on to eject a memory device, like a usb stick, before unplugging to avoid corruption.
TYes but its appearing for my rhino
WA Windows bug with WinUSB subsystem... tried to get rid of it at the driver level, but no luck
TThank you! I just wanted to make sure sure there was nothing I needed to do to fix it. I understand just a bug doesn’t bother anything.
Pbecause il2 devs didn’t answer me (they seems thatt they are busy for il2 korea and new flying circus) I decides to use sticky option but it uses native ffb information even though I turned on sticky option. it is way to low centering force. any idea? kindly help me
TThere should be a tick box in the settings tab.
JWhat's the name / Part number of the USB board side connector (white four pin female)? Mine's still a bit flaky after resoldering and I'd like to build another assembley as backup when / if this one fails
TJST-PH (2.0mm). If you think you will be doing a lot of crimping in the future I would suggest the crimping tool “Engineer PA-24” otherwise just get the cheap crimpers that come with the kits from Amazon.
AAfter last update of telem ffb I’ll-2 does not connect, I noticed I had to reenable it in config, but still no connection, has anyone else had this problem, any suggestions I may have overlooked.
Ndrop your telemffb log here (from %localappdata%\VPForce-TelemFFB\log). Most probaby something else is failing which is prohibiting normal operation.
AOk I’m at work now so I’ll try tonight, thanks
Anevermind, it works now, not sure what happend but the only thing i did was turn up shaking in il-2 force feedback tab from 0 to 100
LI received my Rhino a couple of days ago and have been testing it out - it's as amazing as everyone says it is!
LJust have a quick question - is it recommended to cut off power to the motors (big red button) when it is not in use?
GThat’s exactly what I do. I cut power to it when I’m done flying. And turn it on when I get in the pit.
HI use a switched outlet. Either way, it does the same. It is always good practice to physically cut power to unused devices.
RAre there profiles available for downloading?
LThere are profiles in the #
knowledge-base
knowledge-base
BI have a winwing adapter which was working fine yesterday then today this started. Also button 32 is lit up, I've tried reconnected several times but no luck, all pins are present and noy bent. Can anyone say how to fix this?
Pthat’s a connection issue, you’ll need to contact @walmis
RDCS is having a polling issue with mouses. How often is the vpforce software polling and teleffb polling? since the joystick is constantly moving, i have wondered if its caused some issues like the mouse polling. Just noticed some stuttering witht he ingame fps graph when moving cyclic in game. The stutters on the graph go away whne not moving the cyclic. @Number481
WButton 32 means it's communicating with the base but no connection with the grip, check the top end connection, try pushing/wiggling the 6pin WinWIng plug a little deeper
Nwe use the standard export script which is a loop that executes on every simulation frame. So the rate is effectively equal to your frame rate.
ROk
BDid that several times before and after your msg. On one of the wiggles after your msg I got a few lights flash and now nothing, not even 32. If I purchase another adapter on the sight do I get put on a waiting list? Thanks for the help.
RAnyone here use a motion platform flying IL2? Are you able to get both the Rhino and telem and motion to work at the same time?
MHello! I plan to 3D print a custom throw limiter for my Rhino base. Is there an easy way to do this?
MI know the files for this project are public, but has anyone done somethinhg similar?
BEasy way. Random guesswork and keep guessing til you get it right ?
Or math
Or math
BDont ask me about the second option.