My emergency stop button has stopped working again, is it a logic switch or does it actually cut the

My emergency stop button has stopped working again, is it a logic switch or does it actually cut the power? Just wondering if I can do the same in telemffb rather than stripping it all down for the third time?

GGlaive(Rikk)My emergency stop button has stopped working again, is it a logic switch or does...

Hiob•9/9/24, 5:55 PM

The „emergency“ switch is a real switch that cuts the power physically.

NNumber481 you need to disable the y axis in configurator in order for it to be recognized ...

Jumara•9/9/24, 7:29 PM

Thank you, that did the trick

HHiob The „emergency“ switch is a real switch that cuts the power physically.

Glaive(Rikk)OP•9/9/24, 8:20 PM

Ahh ok, in that case I guess I'll need a new one as it's done this 3 times now.
Thanks

VPS_Choki•9/9/24, 8:29 PM

anybody fly the f-5? and maybe can help with setting up the vpforce

VVPS_Choki anybody fly the f-5? and maybe can help with setting up the vpforce

Kamini•9/9/24, 8:39 PM

I just turn on FFB in DCS and use that. No telmffb and no VPForce configurator open. And that works good enough for me.

VPS_Choki•9/9/24, 8:46 PM

can you trim enough down so u have force on the stick'

Kamini•9/9/24, 8:48 PM

Not sure what you mean with force on the stick? Do you mean that its loose when you trim it far enough down?

VPS_Choki•9/9/24, 8:48 PM

i mean that when u let the stick go the plane goes down

Kamini•9/9/24, 8:49 PM

I haven't tried that much of down trim. Only enough for level flight but I did notice that to achieve level flight my trim was mostly nose down.

Kamini•9/9/24, 8:50 PM

So the stick was forward over the center. I don't even know if that's realistic. Never paid much attention to stick position.

VPS_Choki•9/9/24, 8:50 PM

yeah thats the issue i have the stick being forward of the center

VPS_Choki•9/9/24, 8:50 PM

me and a friend asked a real pilot and he say normally the stick doesnt move atleast in the swiss air force one

Kamini•9/9/24, 8:52 PM

Might be a dcs thing. Cause when you use a non ffb stick and you trim it the stick moves in game

GGlaive(Rikk)Ahh ok, in that case I guess I'll need a new one as it's done this 3 times now. ...

Hiob•9/9/24, 8:52 PM

probably loose connectors. You can tighten them with pliers (after disassembly)

Kamini•9/9/24, 8:52 PM

And I think DCSs ffb just mimics that

VPS_Choki•9/9/24, 8:52 PM

yeah thats for sure i will do some research then

VVPS_Choki yeah thats the issue i have the stick being forward of the center

Hiob•9/9/24, 8:55 PM

That is perfectly normal for any aircraft that isn’t real fly by wire. For level flight at cruise speeds and higher the trim is nose down/stick forward. The faster you go the more the wings want to pitch up, so you have to counter that with trim.

TeufelHunden•9/9/24, 9:32 PM

my computer always has this icon when my base is plugged in is this normal? Is there something I need to do in order to get this to go away?

Rix•9/9/24, 10:21 PM

Is there a setting to keep it from chirping?

TTeufelHunden my computer always has this icon when my base is plugged in is this normal? Is t...

Prometheus [Prom]•9/10/24, 12:33 AM

that just means you have a usb device connected, shouldn’t be an issue. It’s usually used to click on to eject a memory device, like a usb stick, before unplugging to avoid corruption.

TeufelHunden•9/10/24, 1:51 AM

Yes but its appearing for my rhino

TTeufelHunden my computer always has this icon when my base is plugged in is this normal? Is t...

walmis•9/10/24, 6:08 AM

A Windows bug with WinUSB subsystem... tried to get rid of it at the driver level, but no luck

Wwalmis A Windows bug with WinUSB subsystem... tried to get rid of it at the driver leve...

TeufelHunden•9/10/24, 6:37 AM

Thank you! I just wanted to make sure sure there was nothing I needed to do to fix it. I understand just a bug doesn’t bother anything.

PokePoke•9/10/24, 11:19 AM

because il2 devs didn’t answer me (they seems thatt they are busy for il2 korea and new flying circus) I decides to use sticky option but it uses native ffb information even though I turned on sticky option. it is way to low centering force. any idea? kindly help me

RRix Is there a setting to keep it from chirping?

TheAmazinGreat•9/10/24, 12:15 PM

There should be a tick box in the settings tab.

jskibo•9/10/24, 1:03 PM

What's the name / Part number of the USB board side connector (white four pin female)? Mine's still a bit flaky after resoldering and I'd like to build another assembley as backup when / if this one fails

Jjskibo What's the name / Part number of the USB board side connector (white four pin f...

TheAmazinGreat•9/10/24, 1:32 PM

JST-PH (2.0mm). If you think you will be doing a lot of crimping in the future I would suggest the crimping tool “Engineer PA-24” otherwise just get the cheap crimpers that come with the kits from Amazon.

alloyfpv3333•9/10/24, 5:04 PM

After last update of telem ffb I’ll-2 does not connect, I noticed I had to reenable it in config, but still no connection, has anyone else had this problem, any suggestions I may have overlooked.

Aalloyfpv3333 After last update of telem ffb I’ll-2 does not connect, I noticed I had to reena...

Number481•9/10/24, 6:52 PM

drop your telemffb log here (from %localappdata%\VPForce-TelemFFB\log). Most probaby something else is failing which is prohibiting normal operation.

alloyfpv3333•9/10/24, 7:06 PM

Ok I’m at work now so I’ll try tonight, thanks

NNumber481 drop your telemffb log here (from %localappdata%\VPForce-TelemFFB\log). Most pr...

alloyfpv3333•9/10/24, 10:48 PM

nevermind, it works now, not sure what happend but the only thing i did was turn up shaking in il-2 force feedback tab from 0 to 100

Lanceor•9/11/24, 2:18 PM

I received my Rhino a couple of days ago and have been testing it out - it's as amazing as everyone says it is!

Lanceor•9/11/24, 2:19 PM

Just have a quick question - is it recommended to cut off power to the motors (big red button) when it is not in use?

LLanceor Just have a quick question - is it recommended to cut off power to the motors (b...

Greekbull•9/11/24, 2:44 PM

That’s exactly what I do. I cut power to it when I’m done flying. And turn it on when I get in the pit.

LLanceor Just have a quick question - is it recommended to cut off power to the motors (b...

Hiob•9/11/24, 3:20 PM

I use a switched outlet. Either way, it does the same. It is always good practice to physically cut power to unused devices.

Rix•9/11/24, 10:07 PM

Are there profiles available for downloading?

RRix Are there profiles available for downloading?

Lanceor•9/12/24, 9:36 AM

There are profiles in the #

knowledge-base

boobear•9/12/24, 10:19 PM

I have a winwing adapter which was working fine yesterday then today this started. Also button 32 is lit up, I've tried reconnected several times but no luck, all pins are present and noy bent. Can anyone say how to fix this?

Bboobear I have a winwing adapter which was working fine yesterday then today this starte...

Prometheus [Prom]•9/12/24, 11:14 PM

that’s a connection issue, you’ll need to contact @walmis

Reed•9/13/24, 3:34 AM

DCS is having a polling issue with mouses. How often is the vpforce software polling and teleffb polling? since the joystick is constantly moving, i have wondered if its caused some issues like the mouse polling. Just noticed some stuttering witht he ingame fps graph when moving cyclic in game. The stutters on the graph go away whne not moving the cyclic. @Number481

Bboobear I have a winwing adapter which was working fine yesterday then today this starte...

walmis•9/13/24, 5:51 AM

Button 32 means it's communicating with the base but no connection with the grip, check the top end connection, try pushing/wiggling the 6pin WinWIng plug a little deeper

RReed DCS is having a polling issue with mouses. How often is the vpforce software pol...

Number481•9/13/24, 11:07 AM

we use the standard export script which is a loop that executes on every simulation frame. So the rate is effectively equal to your frame rate.

Reed•9/13/24, 12:24 PM

Wwalmis Button 32 means it's communicating with the base but no connection with the grip...

boobear•9/13/24, 12:38 PM

Did that several times before and after your msg. On one of the wiggles after your msg I got a few lights flash and now nothing, not even 32. If I purchase another adapter on the sight do I get put on a waiting list? Thanks for the help.

Rix•9/13/24, 9:00 PM

Anyone here use a motion platform flying IL2? Are you able to get both the Rhino and telem and motion to work at the same time?

Mustang 1-1•9/13/24, 9:15 PM

Hello! I plan to 3D print a custom throw limiter for my Rhino base. Is there an easy way to do this?

Mustang 1-1•9/13/24, 9:16 PM

I know the files for this project are public, but has anyone done somethinhg similar?

Bob Bushman•9/13/24, 9:32 PM

Easy way. Random guesswork and keep guessing til you get it right ?

Or math

Bob Bushman•9/13/24, 9:33 PM

Dont ask me about the second option.

Mustang 1-1•9/13/24, 9:55 PM

Well, I meant more so would someone already have done this and have a file they are willing to share than I can edit. Otherwise, I do not know where to get the correct top part file to edit. If that makes sense

My emergency stop button has stopped working again, is it a logic switch or does it actually cut the

Similar Threads