Disable the y axis so the system knows is a single motor setup.
Disable the y axis so the system knows is a single motor setup.
DIt's not a single motor setup. It's a regular DIY Rhino with two motors.
DUnless you mean like just for troubleshooting?
N
sorry. For some reason I thought you were doing pedals 
DAh, no worries. Thanks anyway!
DHere's my "Device Messages" list from debug tab, if it helps:
D[12:50:07.751] * USB Connected
[12:50:07.921] Reset Motor:7
[12:50:07.921] Motor 0 active
[12:50:07.921] Motor 1 active
[12:50:07.921] Motor 0 timeout
[12:50:07.921] Motor 1 timeout
[12:50:07.921] Motor 0 active
[12:50:59.624] Config received
[12:51:25.215] Config received
[12:51:28.389] Config received
[12:51:28.393] Config written to flash
[13:18:39.957] Reset Motor:7
[12:50:07.921] Reset Motor:7
[12:50:07.921] Motor 0 active
[12:50:07.921] Motor 1 active
[12:50:07.921] Motor 0 timeout
[12:50:07.921] Motor 1 timeout
[12:50:07.921] Motor 0 active
[12:50:59.624] Config received
[12:51:25.215] Config received
[12:51:28.389] Config received
[12:51:28.393] Config written to flash
[13:18:39.957] Reset Motor:7
NLooking closer at your screenshot, it appears the issue is with the X motor connection. Double check the connection between the x motor and the control board?.
As a test I bet if you disabled the X axis, you would see data from the Y axis
As a test I bet if you disabled the X axis, you would see data from the Y axis
DI will try that test. Then I will remove the base screws and check x (roll) motor connections. Back in a few.
DDisabling X and then calibrating gave some kind of values to the Y (instead of just blanks), but it was garbage jittering all over the place and didn't respond to axis motion at all. Will unscrew base bottom now.
DThe motor-end connections appear fine. Green light on both motors and board. Motor data connectors plugged into the correct board ports per the assembly instructions. I'm stumped. Back in 15.
CIs there a wiring diagram for the VKB mount adapter anywhere? I had my mount in a bad place and pinched some wires that I need to re-solder
CSpecifically is it white or black that needs to be resoldered to the blank pin here?
WThe yellow wire is signal
GVPforce FFB Configurator is no longer auto switching profiles whenever i swap between aircraft in DCS. i.e. if i was flying the F-4E and then changed over to the F-14 in my next session, i now have to "alt-tab" out of the game and manually"import" the F-14 profile. It used to automatically change over ..... any ideas ???.
CIsn’t the auto switch a function of TelemFFB, not the configurator?
CGot it working, thanks!!
GYeah TelemFFB is auto switching between profiles ok but VPforce no longer is ???..
BThe configurator never had auto switching, it was always telmeffb.
GThat's strange, for the the past month up until this morning my configurator was changing profiles ???. Which was great, now i have to change the aircraft profile manually, which is no big deal as i only ever really play the same three modules..... but having the automation was nice whilst it lasted :)...
Fyou can set and adapt profiles in TelemFFB which is way better in my opinion because it changes profiles automatically.
GYeah i notice in TelemFFB that there is a configuration override option where you can adjust the spring, damper, master gain etc etc. The trouble is that i make use of a feature called "Gain map" within the configurator "effects" tab where i can adjust the spring gain curve of the "aileron" individually for instance. My preference is to generally set the pitch axis spring gain to feel stonger than the aileron axis as i prefer a lighter feel on the ailerons.
BThere's also a spot where you can select a vpconf file to load.
GYeah that's what i've been using over the past month, my understanding was that i can configure my profile to my liking in VP configurator and then tell TelemFFB to load that profile for that particulur aircraft. It's been working fine up to now, however it dosen't seem to be doing that anymore . Whatever profile i have imported in to VP Configurator is the one that it will continue to use regardless if i change my aircraft in DCS to a helicopter, WW2 bird or a jet..... i need to investigate this further and maybe try and uninstall/reinstall TelemFFB again.... somethings amiss here...
NCheck the log. If there’s an issue loading or finding the file, it will tell you.
Salso, while playing the game telemffb has to remain running, but configurator does not.
CNeed help I'm getting this error
C
SI unplugged my vpforce for a moment as it was conflicting on a game, now i'm back flight simming and i get this and no feedback at all. i have updated telemffb, i have tried multiple planes, restarted msfs twice and started in the correct order. And reset effects
Swhen you open configurator, does it present you a selection like this? then, enter your numbers in telemffb
GYeah that was the problem, for some reason it was no longer recognising my .vpconf files in their original location. Moved them elsewhere and TelemFFB is now loading them ok..... thanks for everybodies input 
CNo, only in telemffb but can't open it anymore
Smight be a usb issue if none of the apps see it
CI entered the wrong PID. Is there a way to delete and start over
Syou can edit the numbers in regedit
CThanks will try it
Sto really start over, you can delete that whole TelemFFB registry folder (its only for the system settings, your planes and profiles are stored elsewhere)
CIt worked. Thanks so much
VDoes anyone ever have problems with the buttons not all working on your stick?
KNo. Which Stick do you have? I use a Thrustmaster Warthog Stick and all is working.
VWinwing stick with attachment
Vto make it work. most buttons work but not all. guess i’ll have to get a TM. Seems something is always up with the winwing and the vp force unless i’m doing something wrong in the configurator
WWhich buttons do not work? WW F-16EX?
VYea F16EX. I will have to check the WW simapppro and find the exact button numbers but the gray (trim) hat switch in all 4 directions plus pressing down doesn’t work. As well as the black 4 way hat switch below it and to the left of it. But again i will have to get back on here in a bit and see which exact buttons don’t work.
THave you tried using the option for hats as buttons? Either checked/unchecked.
VI will try that here shortly and report back. Thanks!
WAlso make sure to select WW adapter grip profile
VI just saw that in the manual as well! Thank you! I will check the manual better next time before reaching out.
Absolutely love my Rhino!
Absolutely love my Rhino!
VThis was it! Thanks again!
MI had a look around and I could not find an answer, only somebody asking a similar question before: I can not get the configurator to recognize the brake lever as well as some of the buttons on my first generation T-50CM, when using the T-50CM2 grip type. Is there any workaround, or solution?
T@Touch_Of_Legend may be able to help if not Walmis himself