I have a sim racing rig, just need one to mount the rhino on to use in VR for helos, A-10 and generi
I have a sim racing rig, just need one to mount the rhino on to use in VR for helos, A-10 and generic flight.
Xyou can get good TrakRacer rig for same money
Xit's the chair that makes a difference... you as virtual pilot/racer have only 3 contact points on rig:
- the butt aka the chair
- hands aka the Rhino
- foot aka the pedals
- the butt aka the chair
- hands aka the Rhino
- foot aka the pedals
Xthose 3 components have to be top noch, rest is subjective
DI have the chair, just need a frame to mount Rhino, throttle, pedals and UFC/keyboard.
Xthen get some TR160 baseline, it's a rig for life, for any upgrades
XTR120 is weavy, might cause issues, but 120mm profiles are more then enough, unfortunately TR switched to this wide body design that is kinda meh
Xand never get simlab angular standoffs also )
Xany 120/160 profile straight rig with proper 90 uprights will work
DTaking a look now.
XMTM has better features built in, if you can afford MTM, get atleast their baseline
Xthey have special cutoff and mount system for center joystick, worth extra. Simracing rig will require some mods to get work, mainly due to seating position, the angle between pedals and seat is much lower on simracing compared to MTM
Xon MTM you sit more upright, much more suitable for Flight, and also have some extra space under the seat. With simracing rig you need to order extra profiles to make it same height. In the end it will end up same cost as MTM
Xjust don't get extras, barebone works, you can add later whatever you need
DDamn! Yeah, MTM is quite a bit more than I wanted to spend since this is a generic setup.
Xany way for local custom ?
Xi know companies offer rigs locally for 50% price of branded ones
DProbably... being in Dallas can probably find anything.
Xthey can just copy MTM and it will be way much cheaper than original one, and also compatible with their accessories
TWhy don’t you use your sim racing rig also for flight sim?
That way you can use your tactile setup and motion for flight sim.
That way you can use your tactile setup and motion for flight sim.
DI thought about that, and I possibly would, but getting this big direct drive wheel off and replacing our pedals every time is a constant pain in the ass. I did that for a bit, but it turned out to be discouraging after awhile....
D
Tah ok.
I have my MFG Crosswinds permanently mounted on the bottom of my 4080 rig and I just have to mount the throttle/ collective and remove the wheel (Simucube QR). It is tight however.
A second rig for flight sim would be great but quite a lot of cost considering the quite expensive tactile setup and motion system. And a second PC. Too much for me.
I have my MFG Crosswinds permanently mounted on the bottom of my 4080 rig and I just have to mount the throttle/ collective and remove the wheel (Simucube QR). It is tight however.
A second rig for flight sim would be great but quite a lot of cost considering the quite expensive tactile setup and motion system. And a second PC. Too much for me.
DI have an extra tactile setup and this one will not be motion. I have the extra HOTAS as well and will use the VR for both my flight rigs (I have a primary motion rig that is setup for F-16 use). I have an extra powered USB hub as well. Only thing I need is actual rig and pedals, a second set of Winwing pedals would work great.
SDNice!
Sthe changeover is quick but i still leave it in flight mode most of the time 
DI found I did the same when I had just one rig. My main fault is being inherently lazy... I want convenience more than anything.
TWhich motion system/ tactile setup do you use?
DI have a DOFReality P6 with a buttkicker mounted on the bottom of the rig using SimHaptic.
BI used to have two pits, two computers, etc. It never failed that i wanted to use X on pit 1 but i preferred accessory Y on pit 2. So i ended up still swapping stuff half the time. Now i have solution similar to what Smitty has.
BNow im working on a stable quick change solution for my Rhino so i can easilly swap it from center to side mount for when i have the urge to fly the 'bus or star citizen
TThis is what I use on my 4080 rig for the Rhino, the collective etc…
TThe bottom permanently mounted on the rig. And the top part attached to the mount plate of the Rhino for example.
TAFAIK this also a company which sells such QR for sim/flight rigs. Maybe someone can chime in….
BThanks for the idea, but ill likely be fabricating my own solution.
Bbut the QR sim guys stuff is intreaging
TQR4rigs, Quick Release Mounts for Sim Rigs : - Quick Release System Dust Covers & Support Plates Universal QR4rigs Systems Quick Release Base Mounts QR by Controller Type Designed for DOF Reality rigs QR by Controller Make Controller Accessories Custom Designs quick release, quick release mounts, sim rig, rig, mounts, controller mounts, joystic...
TI might end up getting a mount from these guys but which one did you get and how did you mount it?
Seems a bit pricey for the full kit.. like $150?
So I’m not really sure I need a $150 mount but hey… those are the brakes sometimes.
Thanks
Seems a bit pricey for the full kit.. like $150?
So I’m not really sure I need a $150 mount but hey… those are the brakes sometimes.
Thanks
II have a lot of their stuff for my rig. My Rhino, side sticks, and throttles are on his release plates.
PGot any photos handy?
V:package: 
RHINO #0714 Has Shipped!
RHINO #0714 Has Shipped!V:package: 
RHINO #0715 Has Shipped!
RHINO #0715 Has Shipped!
CI'm quite excited about this one!
V:package: RHINO #0716 Has Shipped!
RHINO #0716 Has Shipped!TNo I went for the QRs from amazon that I posted above (red color). Attached to my 4080 rig from the bottom and the top detachable part attached to the Rhino mount plate or the collective.
TAmazon? Got a link or what should I search? Thanks!
DSame here, I have a lot of the QR stuff on my current rig.
DMy main rig has become solely F-16, so I will need one for everything else.
TCar Steering Wheel Quick Release Hub Adapter, Universal Snap Off Boss Kit, 6 Hole Models
THere on my rig for the Rhino and for the Virpil collective.
