Has anyone tried the new force feedback for DCS Chinook yet. Just wondering if it’s working ok now.

Has anyone tried the new force feedback for DCS Chinook yet. Just wondering if it’s working ok now.

Currently have it setup as force feedback via the software.

CCowboy10uk Has anyone tried the new force feedback for DCS Chinook yet. Just wondering if ...

Number481•10/2/24, 6:45 PM

seems like it works at a basic level.. but as far as I can tell, no sort of AFCS is implemented yet

NNumber481 seems like it works at a basic level.. but as far as I can tell, no sort of AFCS...

Cowboy10ukOP•10/2/24, 6:46 PM

Thanks, hopefully the AFCS will be implemented soon

HrEple•10/2/24, 6:58 PM

Regarding fastening screws on the gooseneck from virpil. Is it the external two screw on the gooseneck, or the two screws on top “inside” near the connector. I need to fasten “something”.

edit they were all loose - tightened all of them.

And context - my virpil grip is loose even when screwed on tight to the gooseneck.

buzzbomb•10/2/24, 7:39 PM

need more context

buzzbomb•10/2/24, 7:40 PM

the two screws at the top and bottom secure the respective aluminum threaded inserts to the extension. the two screws inside the top threaded connector secure electrical connector to the threaded insert. IF you are running a TM stick grip its reccomended to remove the two screws on the electrical connector so you can put an offset (twist) in the grip

buzzbomb•10/2/24, 7:41 PM

it also reduces the chances of bending the pins on a TM grip as there is no centering/alignment feature on the extension

HrEple•10/2/24, 7:44 PM

Running a CM2 grip from virpil. I should perhaps losen the electrical connection screws if I want to run it offset? Or is that a feature in the grip perhaps - that the connector is already able to twist.

muddy.props_airbrushhero_•10/2/24, 8:15 PM

Hey guys, is there a list of which grips are working in which way (eg. all buttons or just a few) with the rhino? Im thinking about switching out my vkb Gunfighter and looking for a replacement, including an extension. I‘m especially interested if the new virpil flnkr would work with it.

HrEple•10/2/24, 8:34 PM

Pretty sure the flnkr grip will be supported. Asked the same question at some point and learned that walmis is getting one himself. Fingers crossed

DDuchess ✈I thought about that, and I possibly would, but getting this big direct drive wh...

Alkman•10/2/24, 8:59 PM

I build a Flight/Drive Rig like this. Everything stays in place when flying or driving except the Rhino. It is mounted with a Quick release system.

Alkman•10/2/24, 9:00 PM

Alkman•10/2/24, 9:00 PM

Alkman•10/2/24, 9:00 PM

Alkman•10/2/24, 9:01 PM

I just slide my seat forward for driving, after unplugging the Rhino.

Jon (Bounty_V)•10/2/24, 11:19 PM

That's a solid idea

FlyingDutchie320•10/3/24, 5:14 AM

Any idea how long between putting a order request in and receiving a invoice for a diy kit? Thanks

FFlyingDutchie320 Any idea how long between putting a order request in and receiving a invoice for...

DARRYL•10/3/24, 5:24 AM

Next business day or so, IIRC.

Fierce_Fire•10/3/24, 5:45 AM

Yeah, quick

SR-F_Winger_[73]_David•10/3/24, 11:09 AM

Hey Folks. Just a quick Note:
Guys i Made one Monster Rhino Kit (based on @TheAmazinGreat s Project) for a Guy. To save some shipping Cost i ordered parts for a second Kit wich is now ready to Ship.
For Info See Here https://forum.dcs.world/topic/357705-monster-ffb-rhino-diy-kit-supplyservice-supplementary-to-kaltokriwinger-kits/

If you're interested PM me for Fürther Details.

ED Forums

Monster FFB Rhino DIY kit supplyservice (Supplementary to Kaltokri/...

Hi Folks, Based on the awesome Work of @TheAmazingGreat (thanks for your permission to use your Work AS a Base) I made some slight changes and am offering a VPForce MONSTER Rhino Kit sourcing service. The "Thing" kit has the following Specs: - Gimbal printed from laser sintered PA12. - Grip-Conne...

Nemisis Wolf•10/3/24, 11:11 AM

So VP Rhino Ser No:708 got delivered an hour ago! SOOO excited! Now just to find out what to do next and mount it!

VPforceBot•10/3/24, 12:20 PM

:package:

RHINO #0718 Has Shipped!

VPforceBot•10/3/24, 12:20 PM

:package:

RHINO #0717 Has Shipped!

VPforceBot•10/3/24, 12:20 PM

:package:

RHINO #0719 Has Shipped!

ReapDaddy•10/3/24, 6:38 PM

So excited! Just got my email to order. Can’t wait

tanr•10/3/24, 8:45 PM

I'm liking the new G-Force effect! Much easier to keep pulling consistent Gs for tactical turns.

hectik•10/3/24, 10:27 PM

One of the options on the Order Request form for the base is the 'Machined Aluminum Grip Mount Upgrade'. Is the grip mount that comes with the base not aluminum? What's the difference? Just cosmetic?

HHrEple Regarding fastening screws on the gooseneck from virpil. Is it the external two ...

Hiob•10/3/24, 10:45 PM

If your goal was to build a machine that is MEANT to un-tighten screws, a Rhino would come very close to that. Well, it‘s main function is to vibrate like crazy.
Loctide! Loctide! Loctide!

Hhectik One of the options on the Order Request form for the base is the 'Machined Alumi...

buzzbomb•10/3/24, 11:51 PM

the normal grip mount that is included is 3d printed. the upgraded one is machined aluminum. If you are like me and swap grips/extentions alot, or just want piece of mind, spring for the aluminum one

buzzbomb•10/3/24, 11:52 PM

for me it was a no brainer

Bbuzzbomb the normal grip mount that is included is 3d printed. the upgraded one is machi...

tanr•10/4/24, 1:55 AM

I didn’t notice that option when I got mine - know if it’s swappable after the fact? Of course my VKB adapter is 3d printed so maybe a moot point…

Ttanr I didn’t notice that option when I got mine - know if it’s swappable after the f...

buzzbomb•10/4/24, 1:56 AM

it should be swappable

Hhectik One of the options on the Order Request form for the base is the 'Machined Alumi...

amadeus•10/4/24, 7:49 AM

honestly, i'd recommend getting the aluminum grip mount regardless. A lot of stress will go into that part of the rhino over time, and it's one less thing to worry about in the long run

Bbuzzbomb it should be swappable

LeLv30_Superbus•10/4/24, 12:42 PM

How would you take the stock grip mount off? I tried once but I couldn't pull it out. I think I need some kind of tool.

VPforceBot•10/4/24, 1:14 PM

:package:

RHINO #0720 Has Shipped!

VPforceBot•10/4/24, 1:14 PM

:package:

RHINO #0721 Has Shipped!

Duchess ✈•10/4/24, 2:07 PM

I have gone through two 3D printed grip mounts. Get the aluminum one. The 3D one is crap.

DDuchess ✈I have gone through two 3D printed grip mounts. Get the aluminum one. The 3D ...

SR-F_Winger_[73]_David•10/4/24, 5:37 PM

if you have it printed from PA12 its pretty sturdy and should hold up for a standard rhino

SR-F_Winger_[73]_David•10/4/24, 5:38 PM

if standard FDM print i would have it printed lyiong down and then cut the thread on top with a thread cutter

SR-F_Winger_[73]_David•10/4/24, 5:39 PM

this way the layers are not predestined break points every .2mm;)

DDuchess ✈I have gone through two 3D printed grip mounts. Get the aluminum one. The 3D ...

Hiob•10/4/24, 6:25 PM

Self printed? Material, Settings, Orientation?
Because, so far, even with 20cm extensions my printed connector holds strong. I don’t think it will fail anytime soon (knock on wood)

superbird1011•10/4/24, 6:29 PM

Is there any way to use the vpforce kit to create a yoke? Or any plans for an ffb yoke?

ReapDaddy•10/4/24, 6:36 PM

Can I add the aluminum mount to the order I just confirmed? It is in processing stage and I am receiving RHINO #0840 when it is completed.

RReapDaddy Can I add the aluminum mount to the order I just confirmed? It is in processing...

FlatSpin•10/4/24, 6:40 PM

can you DM @walmis

Duchess ✈•10/4/24, 6:41 PM

Not self printed. The first one that came with the Rhino broke, kind of freakish, it snapped forward with force and hit my "cockpit dash". It broke. Second one I had printed, it broke from stress. I understand this is not normal, but I would advise getting an aluminum one... preferably with an offset.

FFlatSpin can you DM @walmis

ReapDaddy•10/4/24, 6:43 PM

done, thanks

tanr•10/4/24, 9:54 PM

Have ordered the aluminum grip mount, but in the meantime (or even once the aluminum version is mounted) any suggestions for keeping the 3D printed VKB adapter solidly attached to the base grip adapter? Loctite blue? Something else?

DARRYL•10/4/24, 10:10 PM

IDK, but I thought Loctite makes at least some plastics brittle. Haven't tried it on 3D printed stuff yet though.

tanr•10/4/24, 10:19 PM

Yeah, that’s my concern. Plus if it melts into the plastic/resin could be non-reversible.

Duchess ✈•10/4/24, 11:27 PM

I also advise against loctite.

DARRYL•10/5/24, 12:39 AM

Could maybe make the joint tight as desired, then drill it for a metal side-screw. Similar to how the metal pulleys have a set screw, but drilled right into the inner piece too. Or kinda like a castle nut / cotter pin joint. Never tried this personally in printed parts, so it might be better to use sacrificial test parts first. Just an idea.

Has anyone tried the new force feedback for DCS Chinook yet. Just wondering if it’s working ok now.

Similar Threads

Similar Threads

Similar Threads