That would eat away some of its capacity. Regarding the heat, when the Moza produces the same amount

That would eat away some of its capacity. Regarding the heat, when the Moza produces the same amount of torque (which it does by the specs) it will produce roughly the same amount of waste heat, no way around that. Given that it not even has ventilation slots…..

AndyHill•10/12/24, 6:54 PM

I share your assesment, but until someone tests it, it's just guesstimation

AndyHill•10/12/24, 6:54 PM

maybe they use superconducting materials or perhaps it runs on fairy dust and produces no heat

AndyHill•10/12/24, 6:54 PM

or does fairy dust produce heat

AndyHill•10/12/24, 6:55 PM

and yes compensating for the motor's inertia takes some power, but again the question is how much and of how much

HHiob That would eat away some of its capacity. Regarding the heat, when the Moza prod...

Daniel V•10/12/24, 7:36 PM

In theory couldn't I just turn the force down to half?

DDaniel V In theory couldn't I just turn the force down to half?

HiobOP•10/12/24, 7:41 PM

Yeah, less power less heat, but that would contradict its purpose wouldn’t it?

The problem with the Moza is that (so far) all „tests“ seem to be sponsored. At least I haven’t seen an independent (and competent) test yet.

AndyHill•10/12/24, 7:42 PM

sponsor me a moza base and I'll do a sponsored test

AAndyHill sponsor me a moza base and I'll do a sponsored test

HiobOP•10/12/24, 7:46 PM

Yeah, me too!

superbird1011•10/12/24, 9:39 PM

I have an issue with the VPForce in MSFS. It feels like the FFB is inverted? You need alot of power to overcome the centre but not alot of force as you put more input in so I end up having hyper unstable planes that only like full ffb inputs.

Warwolf09•10/13/24, 12:13 AM

Hello guys! Just wondering is it possible to use the rhino base as a collective for helis?

Bob Bushman•10/13/24, 12:50 AM

You can diy an actual collective with a single motor kit.

Warwolf09•10/13/24, 1:10 AM

@Bob Bushman i already have the base so i was thiunking on using that. just wondering what settings i need to setup for the autopilot be able to move the collective axis

Bob Bushman•10/13/24, 1:12 AM

That would require the sim to have built in ffb for collective and none do.

WWarwolf09 @Bob Bushman i already have the base so i was thiunking on using that. just wond...

Col. Sanders•10/13/24, 1:57 AM

Why would you use the rhino as a collective and not the cyclic?

Bob Bushman•10/13/24, 2:23 AM

Only good reason i can think of is he has two

Warwolf09•10/13/24, 2:45 AM

I do hahaha

Warwolf09•10/13/24, 3:04 AM

@Bob Bushman looks like its possible with TelemFFB and the. H145(which is what i fly)

Number481•10/13/24, 3:14 AM

Give it a different PID. Add it to TelemFFB as a collective. It will do collective things on the y axis.

NNumber481 Give it a different PID. Add it to TelemFFB as a collective. It will do collect...

Warwolf09•10/13/24, 3:17 AM

How do i add it to TelemFFB as a collective?

Number481•10/13/24, 3:23 AM

https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/mobilebasic#h.vq9olbg3m4ll

Google Docs

VPforce Rhino Manual

VPforce RHINO FFB User Manual Version 0.81 (WIP) Table of Contents 1. Welcome 1 2. Getting Started 3 2.1. Technical Specifications 4 2.2. Physical Setup 5 2.2.1. The VKB Adapter 6 2.2.2. The WinWing Adapter 6 2.2.3. The RHINO Throw Limiter Adapters 7 2.3. Initial Connection and Updating ...

NNumber481 Give it a different PID. Add it to TelemFFB as a collective. It will do collect...

Mike T•10/13/24, 4:49 AM

I too am interested in FFB collective…….using a VPF motor on a custom built collective to use with the X-Trident’s A109SP …..why?…..because in a 4-axis AFCS the collective with trim feel engaged will actually respond power changes. If you press the trim feel trigger underneath the collective it will disengage the trim feel and allow manual control…….i feel that the VPF motor would be perfect to make such a realistic collective. But not sure if it can…..??

BOO•10/13/24, 8:34 AM

Quick question- im down below 150 on the wait list. How are we contacted when its time to place an order? I dont want to miss it if an email ends up in my junk folder. Thanks

BBOO Quick question- im down below 150 on the wait list. How are we contacted when it...

hectik•10/13/24, 9:53 AM

You'll get an email and a message from VPforceBot.

Hhectik You'll get an email and a message from VPforceBot.

BOO•10/13/24, 9:53 AM

Thanks

Youtch•10/13/24, 11:43 AM

What is exactly the additional length of built-in extenstion compared to vkb or virpil base? From the dimensions it looks like it is 160mm from the axis of rotation, and in my vkb it looks like i am only 40mm from the axis rotation (my guess, it might be more), hence I was assuming that you have defacto a 120mm extension built in. Has someone measure this more accuretely?

YYoutch What is exactly the additional length of built-in extenstion compared to vkb or ...

HiobOP•10/13/24, 12:18 PM

From the point of rotation to the top of thread it‘s ~140mm measured from the CAD files.

MMike T I too am interested in FFB collective…….using a VPF motor on a custom built coll...

Number481•10/13/24, 12:32 PM

Not without collaboration from ~~(and likely significant work by)~~ the developer. Edit Well, after looking at some info about the heli, it seems there is at least some provisions built in to allow for springless joysticks and/or FFB implementations. But its unknown how or if this extends to the collective axis. Also I don't own the aircraft nor have access to the manual to even try to get a sense of what it would take

HHiob From the point of rotation to the top of thread it‘s ~140mm measured from the CA...

Youtch•10/13/24, 1:49 PM

Thank you! Any idea on how does it compare with vkb or virpil?

HiobOP•10/13/24, 1:51 PM

My VKB has no more than 45-50mm to the connector. I would guess Virpil is about the same.

HiobOP•10/13/24, 1:54 PM

In my personal opinion the Rhino works best as a center/floor mount stick with extension. As a side stick e.g. it is not well suited.

Oneill•10/13/24, 6:49 PM

Well guys, I’ve not flown in the ikarus for over 9 months, I added the force feedback stick to my simulator to help with my training.
Today I took off unassisted, first landing was a bit crap, but the next 7 touch and goes were as my instructor said, bloody perfect.
So if anyone says Spending all that money on it is a waste, tell them they don’t know what they are talking about.
Looking to be going solo in the middle of December weather permitting.

Bob Bushman•10/13/24, 7:15 PM

If its fun its not a waste

, I think it's getting better but I still wouldn't rely on my home pit, even with rhino and vr, but I do think it can help more to keep the mindset running than say chair flying or just staring at flight instrument posters if you are weeks maybe even months between actual flights.

Warwolf09•10/13/24, 8:43 PM

Just in case anyone wants to do something similar. I was able to modify one of my hotas mounts in my Next Level Racing Military Edition Chair. Pretty easy just need to make a couple of new holes and you can use the rhino as a collective! Works great with the H145. Autopilot moves the collective. Let me know if you want more info on how to modify the mount

Fr4Ged•10/13/24, 9:00 PM

that is a wild setup

Warwolf09•10/13/24, 9:20 PM

@walmis i wish we had native support for the Virpil Hawk-60 collective grip! It would be awesome

SR-F_Winger_[73]_David•10/14/24, 6:15 AM

Hello everyone. Small reminder. I git one Kit ready to Ship to build a Monster Rhino that IS able to Take the biggest VPForce Motors 86BLF04.
Two opinions on the Base you can find Here:
https://forum.dcs.world/topic/357705-monster-ffb-rhino-diy-kit-supplyservice-supplementary-to-kaltokriwinger-kits/#comment-5533855
Usually i only make These Kit per Order cause the parts are quite expensive but i Made this extra one on Stock. To get my Investment Back now available at a reduced price (PM for Details).
Shipping Worldwide possible.

ED Forums

Monster FFB Rhino DIY kit supplyservice (Supplementary to Kaltokri/...

Hi Folks, Based on the awesome Work of @TheAmazingGreat (thanks for your permission to use your Work AS a Base) I made some slight changes and am offering a VPForce MONSTER Rhino Kit sourcing service. The "Thing" kit has the following Specs: - Gimbal printed from laser sintered PA12. - Grip-Conne...

HiobOP•10/14/24, 7:57 AM

Oh, the urge.....

but I already spent a fortune on Rhino related stuff......

BBob Bushman If its fun its not a waste 😉, I think it's getting better but I still wouldn't ...

Oneill•10/14/24, 10:51 AM

Looking to do my solo in December sometime, then it’s just exams to get out of the way.
Next stop training for my flight instructor course the year after

Hhectik You'll get an email and a message from VPforceBot.

WhiteHawk77•10/14/24, 11:41 AM

What’s the average wait time between that message with the order form to the follow up message to pay?

WWhiteHawk77 What’s the average wait time between that message with the order form to the fol...

hectik•10/14/24, 11:59 AM

Not sure what the average is, but I received the invoice seven days after completing the order form.

VPforceBot•10/14/24, 3:01 PM

:package:

RHINO #0732 Has Shipped!

VPforceBot•10/14/24, 3:01 PM

:package:

RHINO #0735 Has Shipped!

VPforceBot•10/14/24, 3:01 PM

:package:

RHINO #0734 Has Shipped!

VPforceBot•10/14/24, 3:01 PM

:package:

RHINO #0733 Has Shipped!

f14billy•10/14/24, 4:12 PM

Monster Rhino as a center stick and original Rhino as a side stick. Thank you @SR-FWinger[73]_David and @walmis for making this possible! The 86 motors are amazing. They never overheat no matter how hard or how long I pull.

Ff14billy Monster Rhino as a center stick and original Rhino as a side stick. Thank you @S...

Col. Sanders•10/14/24, 4:36 PM

I am assuming the mounting footprint is different? Is that true?

f14billy•10/14/24, 4:38 PM

Width is the same. Length is longer.

f14billy•10/14/24, 4:38 PM

Col. Sanders•10/14/24, 4:40 PM

Wonder if the holes could be adjusted so it could still fit a monstertech mounting plate.

Fierce_Fire•10/14/24, 4:44 PM

Assuming yes, but dunno if you want that

That would eat away some of its capacity. Regarding the heat, when the Moza produces the same amount

Similar Threads

Similar Threads

Similar Threads