Here, you can try doing an independent test using fedit. Create a spring effect and try to change th

Here, you can try doing an independent test using fedit. Create a spring effect and try to change the CP offset as in the example vid

fedit.exe164.77KB

R7-Cedar•10/31/24, 2:11 PM

Thanks! testing it now!

R7-Cedar•10/31/24, 2:23 PM

I hit banner and opened properties, pressed 'Play' button, "ID:5 Spring (100%)" shows up on Loaded effects: pane, however, dragging the slider doesn't move the pointer on the grid.

R7-Cedar•10/31/24, 2:23 PM

Tried on both Spring Axis 0 and Spring Axis 1.

R7-Cedar•10/31/24, 2:25 PM

The "ID:5 Spring(100%)" grays out shortly after I stopped moving the slider.

R7-Cedar•10/31/24, 2:28 PM

Oh, I see some errors,

walmisOP•10/31/24, 2:28 PM

Oh interesting, what is your usb setup ?

R7-Cedar•10/31/24, 2:29 PM

usb setup? like other devices connected?

walmisOP•10/31/24, 2:30 PM

Like the topology - HUB, direct connection, USB PCIe card or MoBo direct etc

R7-Cedar•10/31/24, 2:34 PM

I have at least one HUB(By Sabrent) in between the Joystick and computer. I'm checking the cable nest behind the monitor now...

walmisOP•10/31/24, 2:37 PM

You can try a direct connection to the computer, see if it helps

R7-Cedar•10/31/24, 2:41 PM

I'm kinda in fear of it solves the issue since you saved me in same exact way last time...it would be embarrassing I haven't try it before I ask...working on it now...

R7-Cedar•10/31/24, 2:45 PM

Oh it's following my dragging the slider now, I'm so glad and feel dumb same time. Launching the dcs now to see...

Wwalmis Here, you can try doing an independent test using fedit. Create a spring effect ...

kaltokri•10/31/24, 2:56 PM

What is fedit.exe good for?

R7-Cedar•10/31/24, 2:57 PM

The FFB is back on the dcs now, I plugged the pedal back on. Now both the VP-FFB boards are directly plugged into the computer, not via USB HUB. Thank you again Walmis, I'll forcus on USB moving forward. I really appreciate!!!

Kkaltokri What is fedit.exe good for?

walmisOP•10/31/24, 3:17 PM

Testing, mostly

Nozzledude•10/31/24, 5:12 PM

Uh... I get this from the que bot this morning:

Nozzledude•10/31/24, 5:14 PM

is that a minus or a ~?

Pyepye•10/31/24, 5:22 PM

it's approx 36 days

rockerverb08•10/31/24, 5:59 PM

Hello, the axis on my unit do not appear to be reading. VP force sees that the USB in connected but no axis. Same goes with the webpage that pops up when you plug in the base. Does read any axis movement.
For background, I’m plugged directly into a known working USB on my computer.

Additionally, the female barrel power port on my unit has come untethered to the base. Not a very great design.
Any help appreciated.

f14billy•10/31/24, 6:13 PM

I think both issues are related. Can you take a picture of the configurator screen and of the female barrel power port? My guess is that there's no power to the motors due to the power port issue.

Caput_58•10/31/24, 6:15 PM

Putting this here for others with same issue. Had a problem with my beloved Rhino yesterday. It stopped reading the axes or moving. The potentiometer would still work. After a little bit of troubleshooting, I realized that the emergency stop knob seemed loose in its housing. After searching in vain for a YT video of someone taking apart one of these beasts, I gave up and started removing screws. I started on the top, which was.. wrong. Eventually I moved to the back side. After pulling away the side I discovered the knob had loosened enough to twist a little every time I turned it back on. The two wires twisted around each other until eventually one pulled free of its terminal connector. Repair would have been simple if I'd had the same terminal connector. Instead, after trying forever to uncrimp it, I just gave up, removed the wire, soldered it to the connector and reinstalled. I did my best to tighten the emergency stop knob back up, but it's hard to get a good grip on it, and I could see having to do this again in the future.

Caput_58•10/31/24, 6:15 PM

Visual aid:

Caput_58•10/31/24, 6:17 PM

I was tempted to try and fab away to keep the nut from rotating, but I couldn't bear the thought of drilling into my precious. Oh, and if anyone knows the part number or size of those terminal connectors, pass it along, so next time I don't need to solder.

Rrockerverb08 Hello, the axis on my unit do not appear to be reading. VP force sees that the U...

walmisOP•10/31/24, 6:30 PM

Yeah so that's the symptom of no power to the unit. While USB powers the controller, there's no data from the motors. Make sure the DC plug is all the way in and e-stop switch is de-pressed.
Putting some superglue on the DC connector shell from 3 sides and inserting it back into the plastic shell will do the trick (apologies due to QC mistake) .

CCaput_58 I was tempted to try and fab away to keep the nut from rotating, but I couldn't ...

walmisOP•10/31/24, 6:34 PM

The terminal is 2.8mm / 0.5mm

Wwalmis Yeah so that's the symptom of no power to the unit. While USB powers the control...

rockerverb08•10/31/24, 8:48 PM

Thank you for the reply. Apologies if it sounded harsh. At this point I think I’ll need a new base-side plug. Would you be willing to provide a part number for the power plug?

Matchstick•10/31/24, 10:03 PM

is it normal to hear and feel a loud clicking when pushing against the spring in the Rhino ?

mark turner•11/1/24, 9:43 AM

Hi, I have a problem after updating the firmware as prompted. Seemed to go fine but when I started DCS up, there was an error message about the firmware . In FFB config, it says I am at N/A version. When I try and update again, I can pair and connect, but pressing the "update firmware" button does nothing. And I have and error saying wrong firmware configuration version 182, expected 181........can someone help?

mark turner•11/1/24, 9:44 AM

on the update tool it says device firmware is v1.0.17b3

mark turner•11/1/24, 9:44 AM

But I only see v1.0.17b2 available on the list

Mmark turner Hi, I have a problem after updating the firmware as prompted. Seemed to go fine ...

walmisOP•11/1/24, 10:07 AM

Latest firmware is b3
Latest app is b2

Get the latest app and it should be good. You're probably opening the old v16 app with the new firmware installed.

I/JG7_Moto•11/1/24, 12:28 PM

Question about the limiter adapter, have a 20cm extension with the Rhino base, many times the fans start and the FFB resistance goes away after a prolonged dogfight with WWII planes in DCS, by adding a limiter adapter, will that reduce motor stress somehow and allows for longer dogfights before the fans kick in and the force goes away?

II/JG7_Moto Question about the limiter adapter, have a 20cm extension with the Rhino base, m...

Hiob•11/1/24, 12:32 PM

It all boils down to how much amps are applied at maximum deflection/spring. You can check that with the telemetry provided by the VP config. If you want to extend the time of unlimited force, you either need to increase cooling (pretty hard because the hardware doesn’t exactly excel at heat dissipation) or limit the power. (e.g. reducing the spring force gain)

Hiob•11/1/24, 12:33 PM

To directly answer your question - no, limiting the throw on its own doesn’t help.

Hiob•11/1/24, 12:35 PM

With the new fan control option, I would recommend to have always a small airflow around the motors. In other words, start earlier with the cooling.

Hiob•11/1/24, 12:36 PM

Reducing Master Gain would also slow down heat buildup.

I/JG7_Moto•11/1/24, 12:37 PM

How do I get the new fan control option?

II/JG7_Moto How do I get the new fan control option?

Hiob•11/1/24, 12:38 PM

Latest firmware updates and software updates.

I/JG7_Moto•11/1/24, 12:38 PM

Thanks will check them out

I/JG7_Moto•11/1/24, 12:47 PM

walmisOP•11/1/24, 12:48 PM

Ugh, that pesky bug

I/JG7_Moto•11/1/24, 12:48 PM

Seems to be I already have the latest firmware since when I go with the mouse over Update Firmware does not do anything

walmisOP•11/1/24, 12:48 PM

🧰support

walmisOP•11/1/24, 12:49 PM

Try this fix, Device Firmware: -Device Firmware: - should show the actual version afterwards

I/JG7_Moto•11/1/24, 12:52 PM

PS C:\WINDOWS\system32> "HKLM:\SYSTEM\CurrentControlSet\Enum\USB\VID_FFFF&PID_2055&MI_03*\Device Parameters" -Name "DeviceInterfaceGUID" -Value "{DA10CDEF-26A6-47D9-970E-B3D561A277FA}"
At line:1 char:87

... t\Enum\USB\VID_FFFF&PID_2055&MI_03*\Device Parameters" -Name "Device ...
~
Unexpected token '-Name' in expression or statement.
At line:1 char:93
... D_2055&MI_03*\Device Parameters" -Name "DeviceInterfaceGUID" -Value ...
~~~~~
Unexpected token '"DeviceInterfaceGUID"' in expression or statement.
At line:1 char:115
... MI_03*\Device Parameters" -Name "DeviceInterfaceGUID" -Value "{DA10C ...
~~
Unexpected token '-Value' in expression or statement.
At line:1 char:122
... "DeviceInterfaceGUID" -Value "{DA10CDEF-26A6-47D9-970E-B3D561A277FA}"
~~~~~~~~
Unexpected token '"{DA10CDEF-26A6-47D9-970E-B3D561A277FA}"' in expression or statement.
- CategoryInfo : ParserError: (:) [], ParentContainsErrorRecordException
- FullyQualifiedErrorId : UnexpectedToken

I/JG7_Moto•11/1/24, 12:52 PM

Get an error

I/JG7_Moto•11/1/24, 12:54 PM

Fix does not work for me

walmisOP•11/1/24, 12:57 PM

Copy the full line, I see you pasted a truncated string

I/JG7_Moto•11/1/24, 1:00 PM

PS C:\WINDOWS\system32> Set-ItemProperty -Path "HKLM:\SYSTEM\CurrentControlSet\Enum\USB\VID_FFFF&PID_2055&MI_03*\Device Parameters" -Name "DeviceInterfaceGUID" -Value "{DA10CDEF-26A6-47D9-970E-B3D561A277FA}"
PS C:\WINDOWS\system32>

I/JG7_Moto•11/1/24, 1:00 PM

This is good?

Here, you can try doing an independent test using fedit. Create a spring effect and try to change th

Similar Threads