DevHeads IoT Integration Server•14mo ago

imagine doing DSP and streaming stuffs in Zephyr transporting it to Linux for ML jargon

imagine doing DSP and streaming stuffs in Zephyr
transporting it to Linux for ML jargon

melta101OP•11/14/24, 8:38 AM

I'm all in the hype train for OpenAMP

Mmelta101 imagine doing DSP and streaming stuffs in Zephyr transporting it to Linux for ML...

ZacckOsiemo•11/14/24, 8:40 AM

why not

Marvin•11/14/24, 8:45 AM

gone will be the days of sending a jpeg every other millisecond to achieve a poor man's stream.

MMarvin gone will be the days of sending a jpeg every other millisecond to achieve a poo...

ZacckOsiemo•11/14/24, 9:06 AM

What about a perfomant man’s stream

ZZacckOsiemo What about a perfomant man’s stream

melta101OP•11/14/24, 9:51 AM

most video encoder involve a method to find the difference between 2 frames and then send it

melta101OP•11/14/24, 9:53 AM

imagine the BW needed if we send a saperate jpeg everytime

Mmelta101 most video encoder involve a method to find the difference between 2 frames and ...

ZacckOsiemo•11/14/24, 10:52 AM

this is basically a compression algorithm

ZZacckOsiemo this is basically a compression algorithm

melta101OP•11/14/24, 10:55 AM

it is

vinii2508•11/14/24, 12:34 PM

Guys, im using node-red with node-red-contrib-opcua palette, when i use the addFolder command, gives error, somebody knows something about?

Vvinii2508 Guys, im using node-red with node-red-contrib-opcua palette, when i use the addF...

ZacckOsiemo•11/14/24, 12:48 PM

Usually when you want to get help you show what error it is you are facing, as it is your question is too broad to even tackle and likely people can't help.

ZZacckOsiemo Usually when you want to get help you show what error it is you are facing, as i...

vinii2508•11/14/24, 4:14 PM

the error is error:error

Vvinii2508 the error is error:error

ZacckOsiemo•11/14/24, 4:27 PM

You need to dig further. Does your documentation mention this error?

segfaultdev.elf•11/14/24, 4:30 PM

have anyone used CAN before? I was planning to make two devices talk via CAN and taking ADC read from one and writing that into pwm for controlling a servo on the other end
when it works fine Maybe I can Replace the ADC end with pure angular value then I can simulate the car steering workings

Ssegfaultdev.elf have anyone used CAN before? I was planning to make two devices talk via CAN and...

techielew•11/14/24, 5:23 PM

@Umesh Lokhande I think you have some CAN experience, no?

Ttechielew @Umesh Lokhande I think you have some CAN experience, no?

Umesh Lokhande•11/14/24, 5:47 PM

Yes, long back I wrote code to connect the CAN module from Sparkfun with Car's OBD port to read real live data. Here's a video https://www.linkedin.com/embed/feed/update/urn:li:ugcPost:6970616461518123008?compact=1

UUmesh Lokhande Yes, long back I wrote code to connect the CAN module from Sparkfun with Car's O...

melta101OP•11/14/24, 6:33 PM

Damn,
That's amazing

UUmesh Lokhande Yes, long back I wrote code to connect the CAN module from Sparkfun with Car's O...

techielew•11/14/24, 10:52 PM

So what's your question @Undefined? Whether it's possible to simulate steering?

Ttechielew So what's your question @Undefined? Whether it's possible to simulate steering?

segfaultdev.elf•11/15/24, 4:40 AM

no I will implement it. is it relevant?

segfaultdev.elf•11/15/24, 4:42 AM

i’m at learning stage of CAN

Ssegfaultdev.elf i’m at learning stage of CAN

ZacckOsiemo•11/15/24, 6:09 AM

You still asking, this could be done .

aymen ammari•11/15/24, 7:26 AM

Hi Devs, today we visited manipulator robots factory, and the one that impressed me the most is this one welding robot with AI cameras wich detects the object that you wanna weld
What do you think about that

Aaymen ammari Hi Devs, today we visited manipulator robots factory, and the one that impressed...

ZacckOsiemo•11/15/24, 7:42 AM

can you please find out how many computers are used here, like gpos plus rtos systems

ZZacckOsiemo can you please find out how many computers are used here, like gpos plus rtos sy...

melta101OP•11/15/24, 7:48 AM

The industrial hand manipulator I have seen normally run by plc and a CPU

Mmelta101 The industrial hand manipulator I have seen normally run by plc and a CPU

ZacckOsiemo•11/15/24, 8:32 AM

ah that makes sense n

Mmelta101 The industrial hand manipulator I have seen normally run by plc and a CPU

Umesh Lokhande•11/15/24, 8:58 AM

Is it something like the vision sensor/camera will interface to CPU and then data fed to the PLC for control or monitoring?

UUmesh Lokhande Is it something like the vision sensor/camera will interface to CPU and then dat...

melta101OP•11/15/24, 9:05 AM

Actually the ones I had interacted with were non vision based
From what I understood
The CPU handled a GUI display from which you can program it visually like scratch programming, pushing the logic to the PLC, and the PLC to handle control related stuff

Mmelta101 Actually the ones I had interacted with were non vision based From what I unders...

ZacckOsiemo•11/15/24, 10:41 AM

seems like a lot of work, I havent yet really looked into ladder logic I doubt i will but I would be keen to see how a PLC is programmer

ZZacckOsiemo seems like a lot of work, I havent yet really looked into ladder logic I doubt i...

melta101OP•11/15/24, 10:48 AM

i feel the same
instead if PLC, i would rather push myself to learn more about FPGAs

segfaultdev.elf•11/15/24, 11:05 AM

Can anyone help me regarding sampling CAN Tx/Rx Data with logic analyzer I am using a logic analyzer from aliexpres
I implemented the Can Connected Everything and When I monitor Data those are not the data I sent also
I tried bot transceiver they are giving same data so
It is Sure That Transceivers are working FIne Since Data is not AlteredIt is Sure That Transceivers are working FIne Since Data is not Altered

segfaultdev.elf•11/15/24, 11:06 AM

segfaultdev.elf•11/15/24, 11:06 AM

the Data my logic analyzer shows

segfaultdev.elf•11/15/24, 11:07 AM

segfaultdev.elf•11/15/24, 11:07 AM

Data I want so send

Ssegfaultdev.elf Can anyone help me regarding sampling CAN Tx/Rx Data with logic analyzer I am us...

ZacckOsiemo•11/15/24, 11:24 AM

I remember Elicia white was working on a salea plugin for can data do you want to look at that

ZZacckOsiemo I remember Elicia white was working on a salea plugin for can data do you want t...

segfaultdev.elf•11/15/24, 11:24 AM

I am using pulseview

segfaultdev.elf•11/15/24, 11:25 AM

and a cheap logic analyzer I don't know Is it capable or not but it worked fine with I2C, UART, SPI, PWM

Ssegfaultdev.elf I am using pulseview

ZacckOsiemo•11/15/24, 11:25 AM

look at this, it may even detail your issue https://github.com/eleciawhite/canfd-plugin-for-saleae-logic-analyzer

GitHub

GitHub - eleciawhite/canfd-plugin-for-saleae-logic-analyzer: CANFD ...

CANFD Plugin for Saleae Logic Analyzer. Contribute to eleciawhite/canfd-plugin-for-saleae-logic-analyzer development by creating an account on GitHub.

ZZacckOsiemo look at this, it may even detail your issue https://github.com/eleciawhite/canfd...

segfaultdev.elf•11/15/24, 11:27 AM

gonna look into it

segfaultdev.elf•11/15/24, 11:27 AM

also I will program another stm on the other end so that I can verify everything better

Eray Yılmaz•11/15/24, 12:03 PM

Hello everyone,
I am trying to run Mongoose WS on my stm32h753zit6 board but every example they use NucleoH753ZI. They are using RMII mode but in my case I am using MII do I need to update something on library. I tested couple times with different implementations but still my ethernet does not assigning the IP. I am adding the serial log.

Can anybody did this before, can anyone help me about it?