Well this is new. What issue does the telemFFB have?
Well this is new. What issue does the telemFFB have?
BThank you. This worked.
CThe telemffb just does not start. running the exe does nothing, I get the loading spin thing on my cursor for a few fractions of a second, then its just a no start.
WFeels like some runtime libraries are messed up
FHi @walmis I sent you a DM regarding one of the limiters in my last order that was sent with the wrong angles. It was supposed to be Y22 and X16 and I received the standard 11 on both axis.
IRight click on it, then click properties and tick unlock
BHi everyone,
How can I amplify the default TelemFFB plane effects ? So basically what it is for Bf109 in Il.-2 but a notch more
Thx !
How can I amplify the default TelemFFB plane effects ? So basically what it is for Bf109 in Il.-2 but a notch more
Thx !
HIncrease the gain for periodic effects (guns, shudder) and constant force (g-force, de-accel) in the VP config…..and of course master gain if it isn’t on 100
Assuming you already maxed out the settings in TelemFFB
Assuming you already maxed out the settings in TelemFFB
HMake sure you haven’t accidentally limit any force by means of the potentiometer.
Bi have pot #1 to 50% as spring, and the actual Spring force is 100%...so basically 50% spring if i am not mistaken....btw. I have the smaller diamater wheels.
Hcorrect. But spring doesn’t affect the aforementioned effects.
Baffirmative
Bor the smaller cog is slipping ?...as i did 3d print them myself 
HYou mean the motor side pulley?
HBold to make those out of 3D prints. I wouldn’t bet on their longevity. 
Bjup
Bme neither 
HWell at least they are cheap and quick to replace….
HHow many teeth?
Bthats true....i have the alu ones, but the shaft hole is too small 
HThey come in different bore sizes. 8mm is what you need
HMaybe you can drill it up? (be careful, wear glasses and clamp them down properly)
Balready thougth bout it...and will try it out. definitely need a good clamp
HBest to use a standing push down drill. Freehand will be hard to aline.
H(or bite the apple and by new ones)
H*buy
TI'm using throw limiter that is not assymetric. I have 20 degree pitch foward but only 15 deg backward. My stick center is now foward 3-4 degree. How do I correct this?
VI have the same issue, just posted in suggestions to add a recenter option. What I do for now is mess with the Y min/max axes calibration values.
TSo your saying for now I need to change the Y values in order to get a true center.
VOr wait, maybe you have the opposite problem. You calibrated using the throw limiter, and you want your logical center to be different from the physical "middle" position?
TI'm using phycial throw limiters which are not assymetric only for the Y axis. I recalibrated and now the software thinks that the center for me is forward about 4 deg or so. So my stick recenter to the center of the circle on the software but that center is not good for me it is foward 4 deg. I need the circle for center in the software to be back more.
Tis that the same problem you have. This problem cannot be resolved by the balance or static force settings because those settings will not move the center backwards 4 degrees or so it will only move my stick and that's not what I need so I came here for help. 
VYou can probably get there by first changing the Y axis calibration values (to give you more logical throw), then use the software axis scaling to set an asymetric scale for Y. Probably quite a bit of trial and error
VIts similar but different from what I have. I use software endstops and want to use only the "bottom half" of the physical range, but I do want that to be symmetric (I printed an extension that angles the stick forward a bit). By using software endstop scaling, center position remains in the physical middle, so if I have like 1 degree throw for negative Y and 20 degree for positive, which doesnt really fly well
VBut it is what you want I think, just a little less extreme
TMaybe there is no problem for me. I know that it seems my stick is forward at its new center but maybe that's because of the fact my throw is more forward than back and true center for my setup is now foward a little which make sense.
VYeah if you calibrated using the actual physical range (with limiter) stick center will be in the middle of the range.
Tglad I didn't order my new extension with any rake lol now my stick is naturally canted a little forward but thats ok I need to test it out in the sky I'm sure it will be fine
VFWIW, if you want your stick to be upright in the middle, even if that means you have a little less throw in one direction than the other, you can do that (the way I explained) and I find that to feel more natural than I thought. Also, if you just want to offset the weight of the stick, you can do that with the static force setting
Tso change the min max for the Y?
Tchange both an even amount?
TWith stick in its current position note Raw Y value. Move stick to desired center point and note raw Y value there.
If desired-current is positive: under Y axis calibration increase the higher number until C:#### is equal to your desired center raw Y value.
If desired-current is negative:
Decrease the lower number until C:#### is equal to your desired center raw y value.
Then you need to go into axis scaling in effects tab and play with percents so at the physical end stop you get full deflection from the virtual axis.
If desired-current is positive: under Y axis calibration increase the higher number until C:#### is equal to your desired center raw Y value.
If desired-current is negative:
Decrease the lower number until C:#### is equal to your desired center raw y value.
Then you need to go into axis scaling in effects tab and play with percents so at the physical end stop you get full deflection from the virtual axis.
TI think that should work to give you true 20deg fwd, 15deg back
Tok I understand what all these numbers mean the C number and the raw numbers. This makes sense!
Tproblem changing the numbers is not changing the actual physical zero of the stick in the software its just changing the scale of the virtual limit
Tnot gonna work. I just need a way to change the physcial center to not be symmetric zero
TDid you click apply/store? your stick should jump when you change the Y limits and click apply/store.
TThe x and y values at the bottom determine where the physical center is (raw values)
TYou are only changing one of the Y limit values. You should be changing the value in the direction of your lower degree throw in order to push the center toward that direction.
TI changes the max down alot so that the C was the number I wanted when stick was where I wanted it to be centered
Tapplied settings and stick did not move but when I move stick foward it the virtual axis hits the max way before my stick physically hits the limit