Walmis drew the pinout diagram somewhere in the discord, but it's easy to follow it up if you take a

Walmis drew the pinout diagram somewhere in the discord, but it's easy to follow it up if you take a bit of care when removing the small PCBs where the pads and pogo pins are. Those are marked with + / - / data lines, so just connect them and you're fine

VakarianOP•1/26/25, 4:58 PM

IIRC, Red is +, Black is - and the Yellow one is the data

GettinBetter•1/26/25, 10:44 PM

I've ordered a couple of motors in the FFB kits, will there any cables in the box?

GGettinBetter I've ordered a couple of motors in the FFB kits, will there any cables in the bo...

smitty•1/26/25, 10:47 PM

you will need USB-A to USB-B cables

smitty•1/26/25, 10:48 PM

and however you want to hook up the 24v can be whatever connector you like

smitty•1/26/25, 10:48 PM

xt60 recommended

Ssmitty you will need USB-A to USB-B cables

GettinBetter•1/26/25, 10:49 PM

Are all the other connections DIY? Any idea what the PCB sockets are?

smitty•1/26/25, 10:50 PM

they are screw-down-on-the-wire type

Ssmitty they are screw-down-on-the-wire type

GettinBetter•1/26/25, 10:51 PM

Ah thank you.

GGettinBetter Ah thank you.

smitty•1/26/25, 10:52 PM

🧰support

Blackrat•1/27/25, 12:09 PM

Help, just building the MFG pedals Rhino conversion and I cannot get the motor to work, I hope its something simple, I have checked the wiring, tried a different PSU. The software shows power to the board. Any ideas ?

Blackrat•1/27/25, 12:10 PM

Blackrat•1/27/25, 12:11 PM

Its a devilsd job securing to the rig so I really don't want to have to lift it all out lol

walmis•1/27/25, 12:13 PM

Probably a would have been a good idea to test it before installing

What's the LED blinking pattern on the motor?

walmis•1/27/25, 12:14 PM

maybe disabled the wrong axis?

Blackrat•1/27/25, 12:14 PM

I will need to pull it all ou then I guess

Blackrat•1/27/25, 12:16 PM

OKay my motor is a Y axis then not an X axis

Blackrat•1/27/25, 12:16 PM

Looks like it was taht simple many thanks @walmis

Blackrat•1/27/25, 12:18 PM

Teach me to follow the instructions to the letter

walmis•1/27/25, 12:35 PM

@Blackrat you can tick the Swap axis checkbox for it work on X axis and disable Y axis (as required by telemFFB)

Blackrat•1/27/25, 12:36 PM

@walmis Thankyou will try that

Blackrat•1/27/25, 12:37 PM

Perfect, not sure if it matters but keeps in line with others

Wwalmis Probably a would have been a good idea to test it before installing 🙂 What's t...

Blackrat•1/27/25, 12:38 PM

I do like to live life on the edge

Nozzledude•1/27/25, 3:14 PM

What causes “under voltage error”?

walmis•1/27/25, 3:23 PM

When the motor detects voltage less than 8V from the main power supply

NNozzledude Click to see attachment

Rocco Thamanoidis•1/27/25, 9:27 PM

Ehm, did u just try my solution from above?

Rocco Thamanoidis•1/27/25, 9:28 PM

And the undervoltage comes from pushing the emergency button. When it happens next, first what the log before pressing the button to verify.

Rocco Thamanoidis•1/27/25, 9:29 PM

Then try my workaround and shut off MSFS Support in TelemFFB SystemSettings.

Wwalmis When the motor detects voltage less than 8V from the main power supply

Nozzledude•1/27/25, 11:38 PM

What is root cause of that? bad power supply? I just opened it from the box.

Havebug•1/28/25, 9:04 AM

I had a similar issue and found out that the power supply, when motors are under heavy load and demand more current, sometimes can't handle the current spikes and lower the output.
I fixed this by adding a charge tank (basically a capacitor with low ESR) next to each motor.

Havebug•1/28/25, 9:07 AM

I guess you can have a similar workaround by placing a capacitor in parallel at the connector right before it attaches to the Rhino

walmis•1/28/25, 9:27 AM

This shouldn't happen with the stock Rhino. I'll release a new firmware update soon with more diagnostic output and stability improvements, should help debug such issues.

jskibo•1/28/25, 4:18 PM

On latest firmware. Yesterday everything fine, today the configuation software picks up all button and hat presses, but windows and MSFS doesn't register any button presses. TM F/A-18 grip, first time i had any issues

Jjskibo On latest firmware. Yesterday everything fine, today the configuation software ...

walmis•1/28/25, 4:27 PM

If the configurator shows button presses, try loading the default Rhino configuration or checking the button mapping tab, maybe the button mapping is corrupted somehow.

Wwalmis If the configurator shows button presses, try loading the default Rhino configur...

jskibo•1/28/25, 6:18 PM

Thanks That did the trick

Hammer 1-1•1/29/25, 2:18 AM

I need to know if there are a few things I need to get my rhino to work..is there software I need to get?

Hammer 1-1•1/29/25, 2:42 AM

nvm I found the manual

VVakarian Walmis drew the pinout diagram somewhere in the discord, but it's easy to follow...

Tomsk•1/29/25, 2:34 PM

Just an update on this. I took both the Rhino VKB adapter and my VKB made stick extension apart, and directly soldered the two sets of wires together. Works perfectly now. It just means I have a combined stick extension + Rhino adapter, which works fine for me. Thanks for the suggestion

GTOfire•1/30/25, 11:51 AM

Sanity check: I'm finding it super convenient when I hop in and out of my rig to just pop that red emergency stop so the stick tilts forward and out of the way (as opposed to having to step over it while upright).
Should I avoid pressing the emergency stop if not needed, or is this a perfectly safe habit to form that won't cause longevity problems?

Anthony•1/30/25, 12:08 PM

I think it’s “emergency stop when turning it on/off for the day/that gaming session”

Anthony•1/30/25, 12:09 PM

Also I use the dial because sometimes DCS loses track of the device when the emergency button is used, and then starts losing track of what devices are plugged in when it’s turned back on

GGTOfire Sanity check: I'm finding it super convenient when I hop in and out of my rig to...

Xaero Zero•1/30/25, 12:22 PM

it's basically a switch for L1, functions exactly like flip switch, so i guess it's quite safe... until you get Neutral out

Xaero Zero•1/30/25, 12:24 PM

TL;DR; it's safe as any light switch you have a home

Xaero Zero•1/30/25, 12:26 PM

these switches (especially if you have multiple) acts as immersion factor tho, when i get into rig, i do control check as if it was real plane, then i turn on power supply and then Rhino, and do another control check as it was a real plane, kinda fun )

GTOfire•1/30/25, 12:28 PM

Good to know, thanks!
And yeah I've definitely enjoyed a few beautiful moments when I had essentially bound every last button required to do a full F18 cold start, so I could go through the whole sequence without ever clicking something with a mouse.

But that does get old when you have to wait 8mins for INS alignment and you kinda just want to fly

G. R. Cooper•1/30/25, 2:05 PM

Stored Heading is the way!

elijahautistic•1/30/25, 9:20 PM

Hey ! I was wondering if some of you have a very little play on the roll axis (or pitch, depends on how the gimball is mounted i guess)

I can’t really describe it nor show it on camera, but let’s say for example. You roll left and suddenly go right, i feel a very little play.
My guess is that this is just the design of the gimball that creates that

TheAmazinGreat•1/30/25, 10:13 PM

I would tend to agree. One direction will be direct acting and the other direction transfers through the core joint. I think the core joint is where the play comes in. If not play, it is at least extra flex. I also assume this is why you can see different values for force comp on x and y axis in the default configuration.

Rocco Thamanoidis•1/31/25, 5:05 AM

Unfort. the motor timeout/disconnect bug is back. Even with MSFS 2020/24 support disabled.

Rocco Thamanoidis•1/31/25, 5:08 AM

and here at 4:16 compared with the TelemFFB log on the left

Rocco Thamanoidis•1/31/25, 5:09 AM

and at 4:12 also side by side logs

Walmis drew the pinout diagram somewhere in the discord, but it's easy to follow it up if you take a

Similar Threads