Thanks I have a look, do you know if 57BLF03 motors are off the shelf or custom?
Thanks I have a look, do you know if 57BLF03 motors are off the shelf or custom?
TJust got this thing set up with configurator and TelemFFB for the first time. Dumb question: does the stick not behave like a conventional spring base and want to go fully back to center if you stop pushing? I feel like I'm holding it in place in a large dead zone until there are g-forces to push me away.
KI apologize if this isn't the right place for this sort of question, but is the Rhino's base heavy enough that I wouldn't need to bolt it in place with a 200mm stick extension? or must I plan to have some way to fasten it to the floor?
FYou'd at least need to weigh it down a lot more else it would tipple especially with the leverage of the extension
RYup I don’t remember seeing that last night I’ll take another look.
FWoo just put my DIY kit request in 
JAnyone know if it's possible to downgrade firmware?
RI found it. the led. nice
TThe motors have a special anti cogging code so you have to use the motors from VPforce with the kit.
WCan someone tell me this is correct for the VPforce configuration part, because I'm having a little trouble, and it's to use the Vpforce rhino for dcs?
W
FWhat is your issue with using it for DCS?
WI have two indications in red at the bottom right, is this serious?
FCan you screenshot it?
Wok I'll capture it right away
W
W
TYou might have to slip your belts off so the centre value is more correct. Read the note about centre value.
TThe red number is your centre value.
Wso I remove the belts and I continue the adjustments, is that it?
WCould someone tell me the procedure to follow to re-center my motors with respect to the belts, to have a better centering value?
N- remove belt
- manually set min/max to 0/4096, Apply
- enable spring, motor will center
- put belt back on with stick centered on axis
- Run auto calibration, apply, store
Center doesn't need to be exactly 2048... just need to be sure that the range of motion is within 0->4096
- manually set min/max to 0/4096, Apply
- enable spring, motor will center
- put belt back on with stick centered on axis
- Run auto calibration, apply, store
Center doesn't need to be exactly 2048... just need to be sure that the range of motion is within 0->4096
RWould it be good to design or 3-D print a jig that keeps the stick dead center for this process is probably not needed but could be helpful almost like 2/2 squares like a coupling that slides into the plate or someone has a degree limiter installed.
RIt would almost be like printing, a 0° limiter so the stick doesn’t move at all if those are in place why you’re doing thiscenter reset
TSome of the DIY files have one included.
ROh really. Did not know this.
M
Mdesigned a plate to fit me rhino's QR base on my rig
Mfirst time ever touching cad, this was fun
Wit's good I managed to correct the centering values, tell me if this is good now for the first configuration step
W
JCareful. It gets addicting.
JLooks like my USB plug connector housing broke. Does anyone have the stl to replace the VPF base and not the clone?
JThank you, VERY much.
VAfter talking to FedEx on Saturday, which I still hate, now I am informed the base is arriving today.
VJust arrived. May i ask what this is?
V
FThrow limiter. A half of it
VThanks
VHow do i install it?
VAfter auto-calibration, the stick still stays like this. Any help? I have updated both the firmware and the Configurator
WThe calibration only calibrates the extents of the movement range, check the "Balancing the grip" section in the manual, depending of your stick/extension/weight, turning on adaptive recenter might be enough.
https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit?tab=t.0#heading=h.9yc6t8idkb39
https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit?tab=t.0#heading=h.9yc6t8idkb39
Google Docs
VPforce RHINO FFB User Manual Version 0.81 (WIP) Table of Contents 1. Welcome 1 2. Getting Started 3 2.1. Technical Specifications 4 2.2. Physical Setup 5 2.2.1. The VKB Adapter 6 2.2.2. The WinWing Adapter 6 2.2.3. The RHINO Throw Limiter Adapters 7 2.3. Initial Connection and Updating ...
WThere's also a section on how to install the limiter. TLDR: it goes under the dust cover frame, unscrew the 4 screws holding it and slip the limiter underneath then screw them back on.
VThank you sir
RJesus Christ FedEx is bad. That is all.
VWell, at least this time, they listened to my suggestion to delivery one day earlier than scheduled
VAdaptive Recentering does th ejob. Thanks
RLiterally all the way around the world in 5 days. And then.. just.. "sorry we missed you"
WLet's appreciate that it exists at least, other options are friggin' expensive or slooow 
V:package: 
RHINO #0896 Has Shipped!
RHINO #0896 Has Shipped!