Luchador Comments - Answer Overflow

Luchador

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

not fully get you , so you mean meassuring the distance from endstop to the front end of my printbed and place that as 0 ? which code is changing that ?

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

what i just additional did to change the trihorn now the beacon will be 2mm more close to the nozzle that should help me a bit too.

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

how you adjusting it in the config ?

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

thanks i searched a lot but could not find it will try to move it a bit to the front. my beacon is 32 mm behind the nozzle , max offset i can set is 30 so it looks like i was allways super close to the borders and not realised it

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

does anyone know how i could move the z tilt possitions a bit more to the front ? than i could be save that that is not happening anymore

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

i can upload the zip and a video of making a mash tomorrow evening , today i cant get to the printer anymore

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

front in air back nearly milling into the plate

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

yep thats my trouble , it fully makes no sense , like i wrote i also took a 1 mm sheet metql and set the nozzle to 1mm than checked all corners all the nozzle is in a +-0.1mm range to z tilt is working the plat is even to the nozzle but the beacon is measure that wirred mash ,

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 3/12/2025 in #fix-my-printer

bed flat/even but bed mash shows different

every time , and for a try i also did without it no changes

33 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 5/1/2023 in #fix-my-printer

From BL touch to probe not working ?

Morning , last night had some disccutions and some ideas , today checked every line and tried something , finally I found it , in the dont change area at the end the last line was BL Touch Offset ... I removed that line and all was working . few hours bec of 2 lines ( like usual)

4 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 5/1/2023 in #fix-my-printer

From BL touch to probe not working ?

can add tomorrow give up today and was leaving tomorrow can add

4 replies

RRCRat Rig Community [Unofficial]

•Created by Luchador on 4/6/2023 in #fix-my-printer

Stepper Driver Port broken how to chang the Slot on Octopus F446

could it be taht the board has more issues ?

26 replies

RRCRat Rig Community [Unofficial]