Is it please possible to get a pinout for the winwing grips to interface correctly with the rhino bo
Is it please possible to get a pinout for the winwing grips to interface correctly with the rhino board?
WIt's not directly compatible, only via the WinWing adapter
C@walmis when you say winwing adaptor, you mean your adaptor or their adaptor? I have your adaptor but am building my own stick.
WAh, right.
WDMd
CBeautiful thankyou!
TI just got my Rhino and I love it! I am having an issue with the vkb black box where its flashing red and the blue light is also flashing. Is there any idea what could be wrong?
TNevermind I fixed it
LYeah the black box is just trying to say it no longer sees the X and Y axis. Mine's set like this:
JMay I post about a DCS server event we are hosting tomorrow in #
general ?
TYIA!
general ? TYIA!
WYeah, if it's not too late 
JThank you! not too late 
SCan someone please confirm this is correct for TM/virpil?
Been searching high and low and cannot find a definitive pinout.
Thanks!
Been searching high and low and cannot find a definitive pinout.
Thanks!
AHi, I noticed the emergency switch jumped out. How should I put it back?
Nah, upon looking, there's a metal ring inside the case that probably should connect.
Nah, upon looking, there's a metal ring inside the case that probably should connect.
RIs the end stops effects or throw limiter better for setting a end stop. Right now I’ve got the end stops effect clocked with axes reset and it seems to work fine.
RAlso the balance effects for keeping the grip centered. It works but only in one position. For example you tweak for holding center then use the force trim and move stick to high left. Now the new center sags because the balance effects was used for holding the center position. Not sure how it would but a dynamic balance effect to keep the stick truly centered would be nice.
RI also turned my master gain down to 90% and kept my knob at 75%. Does these effect each other.
RReally impressed so far and love it. Can’t fly till Monday how ever. Boo.
WNo, but that would be cool. Hydraulic failures!!
BHi =RS= ddrake1984, Is this your image of the Helicopter Pilot Seat and the RINO. This is how I have to install my RiINO when it arrives.
BFantastic. When installing the RINO this way did you have to make changes to its programming?
DOnly invert of Y axis
RAre you flying the 60 much, I just go tmy rhino installed. I'm hoping to use it tomorrow with DCS and want to get the 60 setup.
NDid you change the mapping in VPForce Configurator? It defaults to spring force, but you can change (or disable) it.
NI'd double check it.. If you somehow, intentionally or not, disabled the setting.. the knob will not beep when rotating it...
NPot 1 defines the function for the knob you are turning. By default it should be set to Spring Gain.
NPot 2 is not wired on the Rhino
Ndo you see the screenshot I just posted?
Nforgot to apply/store ? 
CAnyone know if IL2 provides Damper / Inertia / Friction effects in game, or just spring/periodic? I like some damping but trying to figure out if I'd be over-riding in game settings if I set those to Sticky.
PI don't have my dampening/inertia/friction set to sticky & when I fly something like the A-20 compared to a smaller bird it def feels like there's more inertia/dampening etc.
DFrom my play, IL-2 does not do damper / friction, but havnt tested inertia
WYou can check the Debug tab when in game - it lists all loaded effects from the game
Pwhat's the code to update the telem app again?
T
CI definitely notice heavier spring forces in some planes. For example P-38 has less roll force required, I assume/hope because of the hydraulic ailerons
WYeah it's an easy fix. Apply adhesive/superglue on 3 sides of the connector and pop on the plastic part.
LFWIW I had this happen to mine too and glue has held so far.
Rhow do i get this to work exactly???
RDo i need to use the override trim feature or is it specified in the config.ini for teleffb?
NUse the force trim settings in configurator to set it up how you want it (but not the “sticky” option). If a module doesn’t have force trim FFB, you can use those bindings to use the force trim. If a module supports it, it will override what you have set in configurator (unless you have “sticky” enabled)
VI might have missed a beat, but is the firmware still updated via the https://vpforcecontrols.com/usb/rhino/ ? I'm not seeing a Connect button
AAre you using a browser that supports web usb?
Vah, see it now, thanks
FI completly got rid of stick oscilations when gains are >40% witht the current filter setting on the Friction:
F.
ADoes that not have any other weird side effects tho?
AI feel like low filter like that might create a weird sort of lag effect, but not tested a value this low
WYeah, it's too low. It better to increase the bandwitdth and tune the PID parameters
AIs it one of those things that’s possible to fix if you invest the time? Or is it generally just a problem with friction as an effect?
