Is it possible to change the natural centerposition? I’d like the stick just a little bit closer to

Is it possible to change the natural centerposition? I’d like the stick just a little bit closer to me, basically just trimming it back an inch but have that set as mechanical Center.

Nneok Is it possible to change the natural centerposition? I’d like the stick just a l...

Number481•7/14/23, 7:19 PM

you can adjust the center point by moving the max value lower (or min value higher, depending on the orientation of your Rhino).. but that will sacrafice range of motion in the direction you are adjusting. Alternatively, some (including myself) have made custom offset adapters to get the stick closer without having to move the base closer

Subsonic•7/14/23, 8:54 PM

grub screws on the pulleys on the motors tight?

kingjamez•7/14/23, 9:26 PM

Did your calibration change after making that video?

kingjamez•7/14/23, 10:28 PM

Interesting. If your calibration didn't change that essentially rules out all things related to the belt / gears.

kingjamez•7/14/23, 10:28 PM

If it were me, I'd try and take a look under the cover.

walmis•7/15/23, 4:05 AM

It's strange that it clicks on both axises. I can safely rule out the motors, the pulley could slip, but in this case unlikely, since it usually occurs only on one axis.
If you put back the large gears, hold each axis gear by hand and try to move the stick and try to get a feel for play/looseness.

kingjamez•7/15/23, 6:39 AM

Are the big bearings shifting and clicking between the retainer rings?

neokOP•7/15/23, 7:27 AM

I see a second Potentiometer option in the settings. Is it possible to install a second Poti on the rhino base?

Nneok I see a second Potentiometer option in the settings. Is it possible to install a...

walmis•7/15/23, 9:40 AM

Yeah, there's a JST connector on the mainboard for the second pot

Reed•7/15/23, 2:26 PM

What would you do with a second pot? How could it easily be utilized?

AndyHill•7/15/23, 2:44 PM

maybe if you want to be able to adjust both spring force and effects on the fly

RReed What would you do with a second pot? How could it easily be utilized?

kingjamez•7/15/23, 3:21 PM

There are a lot of options in the VPForce GUI, check it out. It's really helpful when dialing in an effect. You can have control of master for controlling everything and then specify the other pot just for the effect you are trying to perfect.

kingjamez•7/15/23, 3:22 PM

For the DIY crowd I personally wish for the second pot to be co-used as a limit switch so that when things like yokes need to calibrate you could do it automatically.

Original message was deleted

Number481•7/15/23, 3:48 PM

Are you sure the “clicking” is not actually a “creaking”. I get some creaking in the joint between the aluminum square tube and the printed grip/extension adapter. Hard to tell from the video but my video of my creaking sounds similar enough.

kingjamez•7/15/23, 3:51 PM

I get some creaking on mine too but it's not a real rhino...From your video it looks like the sound stopped when you took the top wood off? Is that true?

Original message was deleted

kingjamez•7/15/23, 4:06 PM

That's super important!

kingjamez•7/15/23, 4:08 PM

If you turn the gain all the way to zero, does it still click when you move it?

neokOP•7/15/23, 4:17 PM

So I just drill a hole for mounting in the top plate and connect it, that’s all?

Nneok So I just drill a hole for mounting in the top plate and connect it, that’s all?

kingjamez•7/15/23, 4:59 PM

Yep, make sure your shaft and thread is long enough to be able to tightent the nut on top. I use a 10k pot, not sure what the real Rhino's use but 10k works.

Original message was deleted

kingjamez•7/15/23, 5:02 PM

Hmm... It looks like there is some motor action happening when when gain is turned down because the stick falls when you turn power off. Are you sure that the master gain was actually at 0%?

Kkingjamez Yep, make sure your shaft and thread is long enough to be able to tightent the n...

Reed•7/15/23, 5:32 PM

How would I add a second dial to control master dampening, like the current knob controls master spring ?

RReed How would I add a second dial to control master dampening, like the current knob...

Number481•7/15/23, 5:34 PM

There’s 2 “pot” control settings in configurator. Only one of them is used on the rhino since it only has one pot. If you added a second, and plugged it into the 2nd input, you would just set whatever function you wanted it to have in the configurator.

Reed•7/15/23, 6:20 PM

Very cool. Now need to find the same knob used for the rhino or similar.

Number481•7/15/23, 6:29 PM

These are the ones I bought for my pedals. https://a.co/d/fQrhCgi

Taiss/ 2pcs Black Aluminum Rotary Electronic Control Potentiometer ...

Aluminum knobs are for sound equipments or rotary potentiometer, for protection and easy control. Pu interior is useful to avoid damage and for long time service. great decoration accessory for equipments.hese great looking knobs are high quality and precision machined from an aluminum alloy. The...

Reed•7/16/23, 12:24 AM

What controller do I need to buy?

walmis•7/16/23, 5:13 AM

Hmm, looks like the large pulley bolts are not fully in. Also take note that 2/5 bolts are longer, those go the top-most position for pitch

walmis•7/16/23, 5:14 AM

Maybe it's not seated properly

walmis•7/16/23, 5:15 AM

Did you tighten these bolts?

walmis•7/16/23, 5:15 AM

walmis•7/16/23, 5:15 AM

These need to be "just" tight, since they preload the bearings

walmis•7/16/23, 5:18 AM

yeah, that's good

walmis•7/16/23, 5:19 AM

so yeah, the gimbal should move freely when assembled, without the belt. It's hard to tell in the video above, since the belt is on

walmis•7/16/23, 5:20 AM

yeah, make sure you tighten it straight

walmis•7/16/23, 5:23 AM

There's also this bolt, that sandwitches the gimbal together, tightening it might help with cracking sound (usually on the roll axis)

walmis•7/16/23, 3:40 PM

Can you make a pic from the top? And other angles?

walmis•7/16/23, 3:44 PM

Those 5 hex bolts need to be quite tight (I set the electric driver torque to 15).
Btw did you put the fan grill screw under the gear? because it will touch the gear

walmis•7/16/23, 3:57 PM

Cheers, now you will know the internals too