From the log it looks like the adapter itself works, but it doesn't detect the WW grip via the 6pin
From the log it looks like the adapter itself works, but it doesn't detect the WW grip via the 6pin connector. Is the WW cable fully seated?
�Yes, I've got it down in there as far as it will go. Could the issue be with the adapter even though it shows up? I'm sending one of my WW Grips to a friend that also has a Rhino and WW Adapter to test.
WIt's possible. I've found the socket pins on the 6pin connector sometimes could be in too deep (I've made a video on how to fix it: https://photos.app.goo.gl/um8ZC7NgLJRGkY5U7). The newest adapters (after 2023 July) don't have this problem. If you have a multimeter I could guide you how to test it. If all else fails, I could mail you a new core PCB with connectors.
�I do have a multimeter so please DM the guide. Thx.
WWill do tomorrow, cheers
MOkay I set the setting to loopback and when I go to the trim buttons I can’t figure out how to map them. I click the buttons but nothing happens.
MIs there something else I need to do? I have just set grip type to loopback and then tried ti set the buttons.
MNever mind I figured it out! It was in the manual haha.
SSo, I'm finally back in front of the pc
Here are my current settings
General feeling : way too light
Here are my current settings
General feeling : way too light
SThis feels better actually
SI guess it's gonna need some fine tuning 
AThose settings seem way off 
how long is your extension?
how long is your extension?S20 cm
SWay off for what ?
SI'm just trying to get a "good" feeling, I must admit I have no clue what I'm doing 
A20cm is a bit on the longer side, but that’s a lot of effects I feel like
W@simon2012 I guess you're after center stiffness? Currently the whole force is distributed linearly through the whole throw range, so with an extension it might feel sloppy. Try "Axis scaling" at 50% and see how that goes.
SYes, what I'm definitely missing with the out-of-the-box settings is center stiffness
I'll give a try with axis scaling
I'll give a try with axis scaling
SBy the way, I love the fact you can modify the settings on the spot, super convenient for testing !!! 
TTried DCS with the Rhino for the first time today, the P-51D.
Is there a way to turn down/off engine & gunfire FFB?
Is there a way to turn down/off engine & gunfire FFB?
TIts rattling like h3ck for just barely making a slight bank left or right, whereas in IL-2 it starts rattling when getting close to the limit/edge, at that same point in DCS it nearly knocks a hole in my floor, obviously that's not a tenable situation 
WIn the configurator what's the periodic effects slider at ?
WThat slider controls the rumble effects, it's 50% default
TOh so thats what periodic is for!
I had that maxed out
I had that maxed out
PHey m8, first have you checked ffb in dcs settings?
Pnext have you got the config software installed? & the telem app?
Palso what module?
SPhey m8 sorry I was actually getting my flight gear finally set up in new room. Did you get the Telem app sorted out? there should be a link somewhere to the .exe install version instead of the python version. Telem app works with dcs to add ffb effects to all the dcs modules without interrupting the native ffb effects, these added effects are things like ground texture, landing gear moving into place, flap & AoA flutter etc, gun shake, weapon release effect & others.
NThe documentation may help you get set up.. https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.27yzpife8719
Make sure to grab the latest package from the link in the pinned messages in the TelemFFB channel that smitty linked above. There is also a link to the same downloads folder on the vpforce website in the doc.
Make sure to grab the latest package from the link in the pinned messages in the TelemFFB channel that smitty linked above. There is also a link to the same downloads folder on the vpforce website in the doc.
Google Docs
VPforce RHINO FFB User Manual Version 0.2 (WIP) 2023-10-02 Table of Contents 1. Welcome 1 2. Getting Started 3 2.1. Technical Specifications 4 2.2. Physical Setup 5 2.2.1. The VKB Adapter 6 2.2.2. The WinWing Adapter 6 2.2.3 The RHINO Throw Limiter Adapters 7 2.3. Initial Connection and Up...
DHello, I have a poblem with telem ffb and the Spitfire, when I pass in a waje turbulence the ffb start to pull a random side of all it's power continuously until i turn off telem ffb (if I restant it everything IS fine and it does not happen every Time I pass a waje turbulence)
DI don't find wich effect is on cause, using last release of telem ffb
FRegarding adding ground texture, I dont know if dcs already does this but if it doesnt, could telemffb be used to add ground texture effects to a bass shaker?
NNo. TelemFFB does not interface with any other haptic devices. Other software (such as SimShaker) are specifically built to do that.
Bass shaker software works by playing pre-canned audio files to excite the shaker in various ways depending on the desired effect.
Bass shaker software works by playing pre-canned audio files to excite the shaker in various ways depending on the desired effect.
Ndo you have the wind effect enabled? That particualr one doesnt play very well with wake turbulence. I keep it disabled myself.
DThanks i'm gonna try
DWas that... but that's sad I really liked it
NNYeah, its only on/off currently. I've just added intensity settings for the wind effect, will be part of my next commit
DIt's a really strange effect, in wich the stick get forced in a direction until i restart telem
DMy telem ffb config is almost untouch
PHey @walmis sorry to @ you m8, I'm trying to get my WW f-18 grip to work with the Rhino but it's not showing any button inputs, I have the latest firmware & config tool
PI don't have a ww base either so I can't plu that in to check
WIs it the first time you're trying it? Check the debug tab with debug grip activated, if it's all FFs then the adapter is not detected, otherwise the grip is not detected. There were issues with male pins not reaching and mating with the adapter socket on the grip side.
Pcheers m8 I'll check this now
Pthat's what comes up with grip debug
WOkay, so the adapter itself works, just doesn't communicate with the grip. Did the adapter work before or are you trying it the first time?
Pthis is the first time for the adapter & the grip, I haven't had my flight stuff set up for a while.
WYou can try pushing the grip connector in harder
Pok so I have removed the grip extension & have just the wire from the grip going into the adapter, adapter plugged into the Rhino, when I press a button on the grip the base shaft shakes violently
Wprobably the settings are a bit wrong and there's no weight on the base, you can turn off the motors for testing
