N
NYeah, its only on/off currently. I've just added intensity settings for the wind effect, will be part of my next commit
DIt's a really strange effect, in wich the stick get forced in a direction until i restart telem
DMy telem ffb config is almost untouch
PHey @walmis sorry to @ you m8, I'm trying to get my WW f-18 grip to work with the Rhino but it's not showing any button inputs, I have the latest firmware & config tool
PI don't have a ww base either so I can't plu that in to check
WIs it the first time you're trying it? Check the debug tab with debug grip activated, if it's all FFs then the adapter is not detected, otherwise the grip is not detected. There were issues with male pins not reaching and mating with the adapter socket on the grip side.
Pcheers m8 I'll check this now
Pthat's what comes up with grip debug
WOkay, so the adapter itself works, just doesn't communicate with the grip. Did the adapter work before or are you trying it the first time?
Pthis is the first time for the adapter & the grip, I haven't had my flight stuff set up for a while.
WYou can try pushing the grip connector in harder
Pok so I have removed the grip extension & have just the wire from the grip going into the adapter, adapter plugged into the Rhino, when I press a button on the grip the base shaft shakes violently
Wprobably the settings are a bit wrong and there's no weight on the base, you can turn off the motors for testing
Pnow the debug is all FF & 00
Pyeah I have the red stop depressed & the buttons show up
Wso it started working now?
Pwithout the extension, so I'm just holding the grip with the wire running to base, when I touch the grip male end going into adapter female end it will play up, as for the violent shaking with a button press I'm not sure what that is
WThat's not related to the buttons
WCan you show me your settings?
P
Pthese were with my vkb mcgu grip & adapter
WTry these settings:
Pit goes crazy again straight away even with those settings
WTry spring @2Hz
Pthose blue bars change when the wire to adapter is touched/moved which stops the input from showing
Pspring force lpf?
WYeah
Pnope it goes crazy again
WReduce the spring strength using the knob, when there is no weight attached it becomes unstable with a high gain
Wonce you have everything mounted you can tune it back up
Poh ok, just testing my vkb grip
Pvkb mcgu & 200mm extension everything stable, as you say no weight is making it unstable
Pwould it be ok to put hot glue on the adapter where the ww grip male end goes in? this bit is very finicky, when I just had the wire from grip the button inputs were good, now again with the extension installed it must be interfereing with the connection to the adapter
WDo you use a WW extension or a Virpil?
PWW
Pcan I just trim the wire from extension?
Pit's when it bunches up in the grip that it stops working, is it just normal wires inside?
Wyeah, actually 3 wires are only used
PI think I'll just do this tomorrow when I can get some heat shrink for it
Pcheers for your help m8
FHello after plugging a new control to my pc with DCS open my rhino loose it’s ffb capability just works as a regular joystick, and I have to restart DCS to get back the ffb, any idea what this happens or how to solve it ?
DIt could be the USB hub?
DMight drop power to the RHINO?
FDon’t know maybe has something to do with windows because in my other pc it doesn’t have that behavior
DWith the same USB hub?
FYep
PHow do I calibrate with a physical endstop? do I uncheck software endstop to start I guess? then what about calibration without the stick ending up off set to the front?
PI'm also getting instability when using the default profile & endstops, moving side to aide x axis
P@walmis sorry to @ you again, but can you help with telling me how to calibrate with the physical endstop? cheers m8