Can't say for sure. I've not seen that myself nor had any other reports of similar errors... It lo

Can't say for sure. I've not seen that myself nor had any other reports of similar errors...

It looks like an issue with the simconnect code sending the axis position to MSFS.

How is the stability of your USB connection to the Rhino? Does it ever momentarily disconnect/reconnect by itself?

NNumber481 Can't say for sure. I've not seen that myself nor had any other reports of simi...

Snooper•10/30/23, 2:04 PM

no, just happens in the sim

NNumber481 Can't say for sure. I've not seen that myself nor had any other reports of simi...

walmis•10/30/23, 2:27 PM

0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should recover automatically and probably would be a good idea to put the send_eventsend_event into a try .. except .. block

Wwalmis 0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should reco...

Number481OP•10/30/23, 2:39 PM

easy enough!

Snooper•10/30/23, 2:58 PM

glad to help

Snooper•10/30/23, 4:37 PM

ok, I believe its the engine rumble effect that causing the disconnect of X axis

SSnooper ok, I believe its the engine rumble effect that causing the disconnect of X axis

walmis•10/30/23, 4:41 PM

Can you check the fault code when the axis disconnects? It's in the bottom right in the status bar of the VPConf application

Snooper•10/30/23, 4:42 PM

sdby i'll do it again, I'm in Vr and i doesnt help to this kinds of tests

Snooper•10/30/23, 4:44 PM

Snooper•10/30/23, 4:45 PM

here better than copy the text

Snooper•10/30/23, 4:45 PM

hope not too much serious.. to my end......

Snooper•10/30/23, 4:47 PM

thats why I could recover from it by pressing the red button and then restart it

walmis•10/30/23, 4:50 PM

The safety algorithm is a bit too sensitive, I'll send you a firmware update later

Snooper•10/30/23, 4:55 PM

thanks

Snooper•10/30/23, 4:55 PM

can I reduce the engine tumble too in telemFFB? Look too much

Snooper•10/30/23, 4:56 PM

meanwhile I turn it off

walmis•10/30/23, 5:10 PM

Yeah, there are parameters for reducing the engine rumble

SSnooper can I reduce the engine tumble too in telemFFB? Look too much

Number481OP•10/30/23, 5:20 PM

you can add these to the msfs propeller aircraft config, or to a specific aircraft section:

engine_rumble = yes                     # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled)
engine_rumble_lowrpm = 650              # low RPM threshold for low rpm intensity setting 
engine_rumble_lowrpm_intensity = 0.06   # peak intenstiy of engine rumble at low RPM threshold
engine_rumble_highrpm = 2800            # high RPM threshold for high rpm intensity setting
engine_rumble_highrpm_intensity = 0.03    # peak intensity of engine rumble at high RPM threshold

engine_rumble = yes                     # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled)
engine_rumble_lowrpm = 650              # low RPM threshold for low rpm intensity setting 
engine_rumble_lowrpm_intensity = 0.06   # peak intenstiy of engine rumble at low RPM threshold
engine_rumble_highrpm = 2800            # high RPM threshold for high rpm intensity setting
engine_rumble_highrpm_intensity = 0.03    # peak intensity of engine rumble at high RPM threshold

Number481OP•10/30/23, 5:21 PM

intensity decreases as RPMs increase (defined by the high/low RPM and intensity settngs)

Number481OP•10/30/23, 5:22 PM

I should (and will) add the defaults to the MSFS section

walmis•10/30/23, 5:24 PM

There's also jet engine and afterburner rumble parameters

Number481OP•10/30/23, 5:25 PM

was just assuming they were still flying the comanche based on previous discussions

Snooper•10/30/23, 5:48 PM

yes yes always the comanche!!! i'm true love this month!!! I personally like more the Dash 8 Q200 but i'm on vacation

amadeus•10/30/23, 7:07 PM

@walmis do you know if there's any way to get rid of those chrome/edge webusb notifications? is this just a by product of the type of APIs used by the firmware?

amadeus•10/30/23, 7:07 PM

i.e. whenever a rhino is plugged in, they pop up

Aamadeus @walmis do you know if there's any way to get rid of those chrome/edge webusb no...

Number481OP•10/30/23, 7:28 PM

uninstall all traces of Edge from your machine and then call a witch doctor to make sure it is pure... then install Brave

Number481OP•10/30/23, 7:29 PM

I can't get Edge to stop it either... then the notifications get 'stuck' and the only way to get them to go away is to kill all the edge processes

amadeus•10/30/23, 7:31 PM

chrome does it too lol, so i get double

amadeus•10/30/23, 7:31 PM

but none of my other controllers have this problem, i assuming it's something related to a webusb api?

NNumber481 I can't get Edge to stop it either... then the notifications get 'stuck' and the...

amadeus•10/30/23, 7:32 PM

yeah, if i forget to close it, it seems to get stuck heh, and with an ultrawide, it's something that can sometimes be missed lol

Number481OP•10/30/23, 7:33 PM

Only have Edge and Brave (my default).. Brave will popup if you plug/replug.. but it goes away by itself or you can close it.. edge is a PITA and I think their WebUSB is messed up

amadeus•10/30/23, 7:34 PM

uninstalling the browsers isn't something i can really do given my line of work/job

Number481OP•10/30/23, 7:38 PM

I did find some documentation on hard-disabling WebUSB in Edge via GPO but never went very far down that path

walmis•10/30/23, 7:38 PM

There's a chrome flag that might help:

Wwalmis There's a chrome flag that might help:

Number481OP•10/30/23, 7:38 PM

edge seems to ignore that (I have it disabled)

Wwalmis There's a chrome flag that might help:

amadeus•10/30/23, 8:12 PM

oh sick, will def shut this off in chrome

amadeus•10/30/23, 8:19 PM

i'll try both of these! much appreciated!

amadeus•10/31/23, 5:35 AM

doing this in chrome and edge appears to have fixed the problem! thanks!

NNumber481 you can add these to the msfs propeller aircraft config, or to a specific aircra...

Snooper•11/1/23, 2:08 PM

hi, with the new version and after testing, the engine rumble makes the rhino rumble a lot making it disconnect the X axis as before. but I noticed that if I cut the engine the effect goes away in the TelemFFB but the rhino keeps rumble. any idea? I'll turn it down at low RPM and check. if not I have to turn it off for now

SSnooper hi, with the new version and after testing, the engine rumble makes the rhino ru...

Number481OP•11/1/23, 2:23 PM

it is unlikely that any of the rumble effects are causing your axes to go into protection mode and disconnect. If your screenshot above 🧰support is still accurate, you have the "Periodic Effects LPF" set to 0Hz.. I can't give you a technical explanation, but I can tell you that that will not play nicely with the effects in TelemFFB. The default is 20Hz I believe

walmis•11/1/23, 2:30 PM

Oh yea, didn't notice that! 0Hz on periodic will definitely cause problems, set it to 20Hz @snooperoldschool

Snooper•11/1/23, 2:32 PM

ok, if I changed it it was by mistake because I dont recall messing with that!!!

Snooper•11/1/23, 2:33 PM

I'm positive sure that I didn't change that!

Snooper•11/1/23, 2:33 PM

thanks!

walmis•11/1/23, 2:34 PM

No prob, maybe a firmware update caused it, who knows

Snooper•11/1/23, 2:38 PM

thats was the culprit, problem solved, now i runs like a kitten, so much I need to put more intensity in the low rpm rumble lol

Snooper•11/1/23, 2:50 PM

but I have something here

Snooper•11/1/23, 2:51 PM

if I cut the engine I get all rumbling again until it disconnects.

Snooper•11/1/23, 2:54 PM

If I set engine_rumble_lowrpm_intensity = 0.2 after cut the engine have the same behavior .

SSnooper If I set engine_rumble_lowrpm_intensity = 0.2 after cut the engine have the same...

Number481OP•11/1/23, 2:56 PM

cut the engine on the ground or cut the engine in the air?

Snooper•11/1/23, 2:57 PM

all in the ground

engine_rumble = yes # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled) engine_rumble_lowrpm = 650 # low RPM threshold for low rpm intensity setting engine_rumble_lowrpm_intensity = 0.06 # peak intenstiy of engine rumble at low RPM threshold engine_rumble_highrpm = 2800 # high RPM threshold for high rpm intensity setting engine_rumble_highrpm_intensity = 0.03 # peak intensity of engine rumble at high RPM threshold

Can't say for sure. I've not seen that myself nor had any other reports of similar errors... It lo

Similar Threads