0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should recover automatically an

0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should recover automatically and probably would be a good idea to put the

send_event

send_event

send_event

send_event into a try .. except .. block

Wwalmis 0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should reco...

Number481•10/30/23, 2:39 PM

easy enough!

Snooper•10/30/23, 2:58 PM

glad to help

Snooper•10/30/23, 4:37 PM

ok, I believe its the engine rumble effect that causing the disconnect of X axis

SSnooper ok, I believe its the engine rumble effect that causing the disconnect of X axis

walmisOP•10/30/23, 4:41 PM

Can you check the fault code when the axis disconnects? It's in the bottom right in the status bar of the VPConf application

Snooper•10/30/23, 4:42 PM

sdby i'll do it again, I'm in Vr and i doesnt help to this kinds of tests

Snooper•10/30/23, 4:44 PM

Snooper•10/30/23, 4:45 PM

here better than copy the text

Snooper•10/30/23, 4:45 PM

hope not too much serious.. to my end......

Snooper•10/30/23, 4:47 PM

thats why I could recover from it by pressing the red button and then restart it

walmisOP•10/30/23, 4:50 PM

The safety algorithm is a bit too sensitive, I'll send you a firmware update later

Snooper•10/30/23, 4:55 PM

thanks

Snooper•10/30/23, 4:55 PM

can I reduce the engine tumble too in telemFFB? Look too much

Snooper•10/30/23, 4:56 PM

meanwhile I turn it off

walmisOP•10/30/23, 5:10 PM

Yeah, there are parameters for reducing the engine rumble

SSnooper can I reduce the engine tumble too in telemFFB? Look too much

Number481•10/30/23, 5:20 PM

you can add these to the msfs propeller aircraft config, or to a specific aircraft section:

engine_rumble = yes                     # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled)
engine_rumble_lowrpm = 650              # low RPM threshold for low rpm intensity setting 
engine_rumble_lowrpm_intensity = 0.06   # peak intenstiy of engine rumble at low RPM threshold
engine_rumble_highrpm = 2800            # high RPM threshold for high rpm intensity setting
engine_rumble_highrpm_intensity = 0.03    # peak intensity of engine rumble at high RPM threshold

engine_rumble = yes                     # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled)
engine_rumble_lowrpm = 650              # low RPM threshold for low rpm intensity setting 
engine_rumble_lowrpm_intensity = 0.06   # peak intenstiy of engine rumble at low RPM threshold
engine_rumble_highrpm = 2800            # high RPM threshold for high rpm intensity setting
engine_rumble_highrpm_intensity = 0.03    # peak intensity of engine rumble at high RPM threshold

Number481•10/30/23, 5:21 PM

intensity decreases as RPMs increase (defined by the high/low RPM and intensity settngs)

Number481•10/30/23, 5:22 PM

I should (and will) add the defaults to the MSFS section

walmisOP•10/30/23, 5:24 PM

There's also jet engine and afterburner rumble parameters

Number481•10/30/23, 5:25 PM

was just assuming they were still flying the comanche based on previous discussions

Snooper•10/30/23, 5:48 PM

yes yes always the comanche!!! i'm true love this month!!! I personally like more the Dash 8 Q200 but i'm on vacation

amadeus•10/30/23, 7:07 PM

@walmis do you know if there's any way to get rid of those chrome/edge webusb notifications? is this just a by product of the type of APIs used by the firmware?

amadeus•10/30/23, 7:07 PM

i.e. whenever a rhino is plugged in, they pop up

Aamadeus @walmis do you know if there's any way to get rid of those chrome/edge webusb no...

Number481•10/30/23, 7:28 PM

uninstall all traces of Edge from your machine and then call a witch doctor to make sure it is pure... then install Brave

Number481•10/30/23, 7:29 PM

I can't get Edge to stop it either... then the notifications get 'stuck' and the only way to get them to go away is to kill all the edge processes

amadeus•10/30/23, 7:31 PM

chrome does it too lol, so i get double

amadeus•10/30/23, 7:31 PM

but none of my other controllers have this problem, i assuming it's something related to a webusb api?

NNumber481 I can't get Edge to stop it either... then the notifications get 'stuck' and the...

amadeus•10/30/23, 7:32 PM

yeah, if i forget to close it, it seems to get stuck heh, and with an ultrawide, it's something that can sometimes be missed lol

Number481•10/30/23, 7:33 PM

Only have Edge and Brave (my default).. Brave will popup if you plug/replug.. but it goes away by itself or you can close it.. edge is a PITA and I think their WebUSB is messed up

amadeus•10/30/23, 7:34 PM

uninstalling the browsers isn't something i can really do given my line of work/job

Number481•10/30/23, 7:38 PM

I did find some documentation on hard-disabling WebUSB in Edge via GPO but never went very far down that path

walmisOP•10/30/23, 7:38 PM

There's a chrome flag that might help:

Wwalmis There's a chrome flag that might help:

Number481•10/30/23, 7:38 PM

edge seems to ignore that (I have it disabled)

Wwalmis There's a chrome flag that might help:

amadeus•10/30/23, 8:12 PM

oh sick, will def shut this off in chrome

amadeus•10/30/23, 8:19 PM

i'll try both of these! much appreciated!

amadeus•10/31/23, 5:35 AM

doing this in chrome and edge appears to have fixed the problem! thanks!

NNumber481 you can add these to the msfs propeller aircraft config, or to a specific aircra...

Snooper•11/1/23, 2:08 PM

hi, with the new version and after testing, the engine rumble makes the rhino rumble a lot making it disconnect the X axis as before. but I noticed that if I cut the engine the effect goes away in the TelemFFB but the rhino keeps rumble. any idea? I'll turn it down at low RPM and check. if not I have to turn it off for now

SSnooper hi, with the new version and after testing, the engine rumble makes the rhino ru...

Number481•11/1/23, 2:23 PM

it is unlikely that any of the rumble effects are causing your axes to go into protection mode and disconnect. If your screenshot above 🧰support is still accurate, you have the "Periodic Effects LPF" set to 0Hz.. I can't give you a technical explanation, but I can tell you that that will not play nicely with the effects in TelemFFB. The default is 20Hz I believe

walmisOP•11/1/23, 2:30 PM

Oh yea, didn't notice that! 0Hz on periodic will definitely cause problems, set it to 20Hz @snooperoldschool

Snooper•11/1/23, 2:32 PM

ok, if I changed it it was by mistake because I dont recall messing with that!!!

Snooper•11/1/23, 2:33 PM

I'm positive sure that I didn't change that!

Snooper•11/1/23, 2:33 PM

thanks!

walmisOP•11/1/23, 2:34 PM

No prob, maybe a firmware update caused it, who knows

Snooper•11/1/23, 2:38 PM

thats was the culprit, problem solved, now i runs like a kitten, so much I need to put more intensity in the low rpm rumble lol

Snooper•11/1/23, 2:50 PM

but I have something here

Snooper•11/1/23, 2:51 PM

if I cut the engine I get all rumbling again until it disconnects.

Snooper•11/1/23, 2:54 PM

If I set engine_rumble_lowrpm_intensity = 0.2 after cut the engine have the same behavior .

SSnooper If I set engine_rumble_lowrpm_intensity = 0.2 after cut the engine have the same...

Number481•11/1/23, 2:56 PM

cut the engine on the ground or cut the engine in the air?

Snooper•11/1/23, 2:57 PM

all in the ground

Snooper•11/1/23, 2:57 PM

and the only thing that solves it is disconnect and connect again

Snooper•11/1/23, 2:58 PM

the behavior dont shows at 0.1

engine_rumble = yes # Enable rumble effect (default = 0 (disabled)) - 1=enabled, 0=disabled) engine_rumble_lowrpm = 650 # low RPM threshold for low rpm intensity setting engine_rumble_lowrpm_intensity = 0.06 # peak intenstiy of engine rumble at low RPM threshold engine_rumble_highrpm = 2800 # high RPM threshold for high rpm intensity setting engine_rumble_highrpm_intensity = 0.03 # peak intensity of engine rumble at high RPM threshold

0xC00000B0 is a Windows kernel "disconnected pipe" error. Simconnect should recover automatically an

Similar Threads