Hmm, I cant seem to find that setting in the config
Hmm, I cant seem to find that setting in the config
N
SOh, well that must have been my problem, I was on the stable Telem and the wip has evolved to a far better place. Much better than digging through a txt file. Thanks for indirectly finding me the answer by getting me to update, lol. The problem seems to be gone in this version!
NSorry you had to experience pre-settings interface TelemFFB 
SNo kidding! Also, is the whole trim following thing that you mess with in stable just built in and working on its own in this version?
NIt works the same way, but the various physical and virtual gain settings are all slider bars. It’s all under the “axis control” setting (click the arrow when the setting is enabled to show all the sun settings)
SAh, i see. And it looks like it auto sets it to the current aircrafts settings
NYes. The settings tab will always show the current loaded aircraft. You can edit any aircraft or the sim/aircraft class defaults from the settings menu in the menu bar
SThats cool! seems fairly simple too use but with a hole lot of potential tweaking to dial things in.
WHi all,
Received my Rhino today and have installed everything (VKB MCGU, 10cm extension), however I'm having an issue where the motors are timing out constantly in DCS. The effect is that the controls lock for a second every three to five seconds - i.e. unuseable currently. I've scoured the manual and tried some trouble shooting - reset everything etc etc. I think I'm a little stuck currently...
I've attached a screen shot of the debug screen, as well as the current settings. Really not sure what's going on here but I could really use some help! :/
Received my Rhino today and have installed everything (VKB MCGU, 10cm extension), however I'm having an issue where the motors are timing out constantly in DCS. The effect is that the controls lock for a second every three to five seconds - i.e. unuseable currently. I've scoured the manual and tried some trouble shooting - reset everything etc etc. I think I'm a little stuck currently...
I've attached a screen shot of the debug screen, as well as the current settings. Really not sure what's going on here but I could really use some help! :/
WThat's strange, could be power problems, I'll DM you
YToday suddenly all grip buttons stopped working did anyone had similar issue ? Yesterday everything worked fine today I've noticed that grip buttons stopped working I've tried warthog and alpha none of them gives any input in debug shows me bunch of FF's
Rhino
Rhino
WThat's puzzling for sure. First I'd check the physical wiring. Maybe the grip side socket connector got loose?
Or maybe the solar flare that happened today got something to do with this
Or maybe the solar flare that happened today got something to do with this
YI've just checked that all looks solid and connected , I've also used reset settings to factory which changed everything to some weird settings but still have no input from grip
Chello, quick question here, getting a warning about a trojan virus in the VPforce TelemFFB WIP... i don't think it actually has it, but has anyone else experienced?
Cthanks
Cone smaller question, noticing that the Mi-8 in DCS is not holding the trimmer button, anyone experienced? Both the Mi-24 and KA-50 are working just fine. Also I have special setting FFB stick turned on.
Cmaybe this module doesnt support force feedback? would be sad for a helo
WCheck the trimmer mode in DCS module special settings, maybe that's the culprit
Cset correctly to joystick without springs and force feedback, still have the issue with that setting on.
WYou need to set to instant trimmer
WThat setting means -without- springs and -without- ffb
WI just wanted to publicly acknowledge @walmis for spending some time helping me problem solve this one. It looks like a USB port was playing up. Everything is working fine 
PDid the rubber washer solve your problem?
Fyes @Pikas62, thanks for asking.
NI updated TelemFFB to the new version. now after a restart my shortcut is gone. where is the actual installation now? the previous installed folder has only a couple of files and no exe??
Ndownloaded the latest version and getting this now...
N
TI had this yesterday. Exempt the folder your FFB is in and run the updater again.
NLooks like windows keeps deleting the eye
NExe
TYep
NHow do I exempt the folder?
TGo to Start > Settings > Update & Security > Windows Security > Virus & threat protection. Under Virus & threat protection settings, select Manage settings, and then under Exclusions, select Add or remove exclusions. Select Add an exclusion, and then select from files, folders, file types, or process.
TI have all my VPForce/FFB stuff in one folder, so I just exempt the folder and viola.
NThanks a lot that worked
NWhere are my settings now actually saved?
NIn the export lua?
NIt’s all covered in the manual (section 4.2) including info on migrating old settings file to the new framework.
https://docs.google.com/document/u/0/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/mobilebasic#h.ghj8phqmqr7y
https://docs.google.com/document/u/0/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/mobilebasic#h.ghj8phqmqr7y
Ncheers
DIm wondering what is causing windows to think this is a virus and threat?
J@walmis VP is my first ever use of Python on my PCs and within my network. This article suggests Python can be used against us. How are we protected and how can we protect from the issues in this article? Thanks. https://www.msn.com/en-us/money/other/windows-pcs-are-now-being-hit-by-dangerous-malware-here-s-the-steps-you-need-to-take-to-stay-safe/ar-BB1hrlVF?ocid=msedgntp&pc=U531&cvid=a0947bf222984375a66464bb7e2eaa14&ei=76
Nthis article is moslty clickbait. Do you actually have the python interpreter installed on your machine? Are you downloading random obscure python libraries from pypi? If not.. nothing to worry about.
BI can pretty much guarantee this is not the first time you use python application. It's a very common programming language.
That article, I don't know what that is doing besides trying to scare grandmother's
That article, I don't know what that is doing besides trying to scare grandmother's
SBREAKING NEWS: hackers use programming languages to write malware
BNot to mention they found almost a dozen.
almost a dozen
almost a dozen
BBet there is more malicious things in github, but we can't talk about that since, ms owns that.
J@Number481 You are taking the question as an accusation. Please don't. I don't understand how Python works completely, but do understand rather high level access is granted to the applications. Inadvertently a problem could be introduced by using pre infected code without intent. @TorTorden I can guarantee I never used it because I needed to download it to start using Telem. Again there are no accusations being made at anyone and I fully appreciate the efforts of @Number481 and all other contributors.
Syou can download the exe of TelemFFB so you dont need Python on your pc.