in a real helicopter, do force trim also work on pedals? Or only cyclic?
in a real helicopter, do force trim also work on pedals? Or only cyclic?
Hthis is strange, why with the rhino default config, the X axis is inverted?
Nhere's a clip of centering at %30 spring. I run Virpil pedals with the 8603 motor
Nand my gain map.. just gives it a little more oomph right around center
Tseems to have helped a lot so far
Hok I undrstand about the inverted axis, this is because the default config file does not change the ffb axes setup
WYeah, X axis is usually inverted to work in the right logical direction on the Rhino
HI have an issue calibrating my twist axis. If I want the axis to go from -4096 to +4096 then at neutral the value is not 0. And if I click the C to have it centered at 0 then it goes from -4096 to 3955
Hok I found a solution, I removed a few values to max and increase the min the same value so center does not move but the axis goes to max and min
TLastly, whats a good setup for the Apache? I saw your posts before something bout trim issues in dcs and i think Telem ffb helped solved it.
Nyeah, if you run DCS by itself, you will find that your pedals react to the x axis FFB for the cyclic. TelemFFB overrides that and just sets no springs with a configurable dampening setting
TIm planning on adding ffb to my collective soon, still figuring out how to connect the direct drive to the virpil collective.
Tsweet, was testing it earlier. was trying to look for faults and didnt find any. I did have telemffb running so thats why
T@walmis @Number481 Thank you for your time helping me out guys, much appreciated.
DThx, it seems to be the problem. I tried to unplug those wire and probably damaged the connector. I think îll have to buy a new one.
Awhat types of screws & stuff is Rhino made with, I need to upgrade my set and I want to make sure I get suitable stuffs for screwing rhinos
EIf you mean the force trim release that's only applicable for cyclics. So there is no button that you press that allows you to move the pedals more "lightly".
So no need to push the button and then move the pedals. You can just move them without hitting the button.
So no need to push the button and then move the pedals. You can just move them without hitting the button.
TJust to confirm, will this be able to power a stock rhino, a 1x 86BLF03 and 1x 86BLF04 together? Was afraid it might burn out the stock Rhino motors. Planning on consolidating the power supply to clear out my wire mess.
TThis LRS-350-24 AC to DC power supply safely converts alternating currents into direct currents that your electronic devices can make use of. It has a voltage of 24 V and maximum output power of 350.4 W. This part's single output can handle a current up to 14.6 A. This part has a temperature rang...
FI believe I am using that exact one to power my 2 blf04 motors so yes you should be good
Tcan the stock rhino take 24v?
FYes, the board has a power regulator smth so as long as you stay within its spec nothing should happen to the motors
TAlright, tyvm
MThats a sale right here.....any idea of timescale Walmis?
BHard to say no to that
AI'd estimate you'll get yours some time after I get mine
AI have a Virpil Blackhawk Grip attached to my DIY Collective and connected to the Rhino USB Board. All buttons are recognized, but when i press any of the Hat buttons (up/down,left/right), the corresponding center press button also lights up. I currently have it set to Generic grip, but tried all the other options and there is no change in behaviour. I’ve also tried both the options Hat switch as button, and 4-way Hat.
Any ideas to get this working correctly?
Any ideas to get this working correctly?
WVirpil hats need additional decoding, do any of the existing Virpil grip profiles work for the blackhawk grip?
Can you DM me the "Generic grip (debug)" output in the Debug tab and I'll also need the mapping for the hats, table like this would be very useful. I'll add a new profile to the firmware
Can you DM me the "Generic grip (debug)" output in the Debug tab and I'll also need the mapping for the hats, table like this would be very useful. I'll add a new profile to the firmware
W
AHow do i get the Generic Grip debug output?
Wselect
Generic grip (debug) profile
Cit says MSFS isnt enabled even thouigh i have the game open? anyone know how to fix?
AHere is the CSV file. Is that the correct Debug file?
ABtw: the #2 Button also acts as the Hat buttons. When pressing Up. both Up (13) and Press (12) are lighted.
WAlso please include the Grip debug data as shown 
N1.) You'll want to grab the latest 'WiP" version (see pinned messages here: https://discord.com/channels/965234441511383080/1093558100713279508)
2.) Check out the manual (Section 4.2) https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.ghj8phqmqr7y
While the WIP version is linked in the doc and the github readme, its not always obvious that you probably want that version
2.) Check out the manual (Section 4.2) https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.ghj8phqmqr7y
While the WIP version is linked in the doc and the github readme, its not always obvious that you probably want that version
AYou mean a printscreen of the debug window? Isn't that the same as the samples.csv? Sorry for being a noob..
A
T@walmis Hello. I think the F03 motor I purchased is DOA.
CGot it thank youi
TI turned off my system and swapped with the F04 and it gave all the expected readings on the left panel. Also twisted the axis and showed movement.
TWhen I switched back to this F03 motor, this is what I get
T
T
WCan you check the motor IDs?
Thold on
T
WSo yeah, this one is with Pitch id
WYou need to disable X and enable Y in the configurator
TWorking now! Tyvm!
T