Lastly, whats a good setup for the Apache? I saw your posts before something bout trim issues in dcs
Lastly, whats a good setup for the Apache? I saw your posts before something bout trim issues in dcs and i think Telem ffb helped solved it.
Nyeah, if you run DCS by itself, you will find that your pedals react to the x axis FFB for the cyclic. TelemFFB overrides that and just sets no springs with a configurable dampening setting
TIm planning on adding ffb to my collective soon, still figuring out how to connect the direct drive to the virpil collective.
Tsweet, was testing it earlier. was trying to look for faults and didnt find any. I did have telemffb running so thats why
T@walmis @Number481 Thank you for your time helping me out guys, much appreciated.
DThx, it seems to be the problem. I tried to unplug those wire and probably damaged the connector. I think îll have to buy a new one.
Awhat types of screws & stuff is Rhino made with, I need to upgrade my set and I want to make sure I get suitable stuffs for screwing rhinos
EIf you mean the force trim release that's only applicable for cyclics. So there is no button that you press that allows you to move the pedals more "lightly".
So no need to push the button and then move the pedals. You can just move them without hitting the button.
So no need to push the button and then move the pedals. You can just move them without hitting the button.
TJust to confirm, will this be able to power a stock rhino, a 1x 86BLF03 and 1x 86BLF04 together? Was afraid it might burn out the stock Rhino motors. Planning on consolidating the power supply to clear out my wire mess.
TThis LRS-350-24 AC to DC power supply safely converts alternating currents into direct currents that your electronic devices can make use of. It has a voltage of 24 V and maximum output power of 350.4 W. This part's single output can handle a current up to 14.6 A. This part has a temperature rang...
FI believe I am using that exact one to power my 2 blf04 motors so yes you should be good
Tcan the stock rhino take 24v?
FYes, the board has a power regulator smth so as long as you stay within its spec nothing should happen to the motors
TAlright, tyvm
MThats a sale right here.....any idea of timescale Walmis?
BHard to say no to that
AI'd estimate you'll get yours some time after I get mine
AI have a Virpil Blackhawk Grip attached to my DIY Collective and connected to the Rhino USB Board. All buttons are recognized, but when i press any of the Hat buttons (up/down,left/right), the corresponding center press button also lights up. I currently have it set to Generic grip, but tried all the other options and there is no change in behaviour. I’ve also tried both the options Hat switch as button, and 4-way Hat.
Any ideas to get this working correctly?
Any ideas to get this working correctly?
WVirpil hats need additional decoding, do any of the existing Virpil grip profiles work for the blackhawk grip?
Can you DM me the "Generic grip (debug)" output in the Debug tab and I'll also need the mapping for the hats, table like this would be very useful. I'll add a new profile to the firmware
Can you DM me the "Generic grip (debug)" output in the Debug tab and I'll also need the mapping for the hats, table like this would be very useful. I'll add a new profile to the firmware
W
AHow do i get the Generic Grip debug output?
Wselect
Generic grip (debug)
Cit says MSFS isnt enabled even thouigh i have the game open? anyone know how to fix?
AHere is the CSV file. Is that the correct Debug file?
ABtw: the #2 Button also acts as the Hat buttons. When pressing Up. both Up (13) and Press (12) are lighted.
WAlso please include the Grip debug data as shown 
N1.) You'll want to grab the latest 'WiP" version (see pinned messages here: https://discord.com/channels/965234441511383080/1093558100713279508)
2.) Check out the manual (Section 4.2) https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.ghj8phqmqr7y
While the WIP version is linked in the doc and the github readme, its not always obvious that you probably want that version
2.) Check out the manual (Section 4.2) https://docs.google.com/document/d/1YL5DLkiTxlaNx_zKHEYSs25PjmGtQ6_WZDk58_SGt8Y/edit#heading=h.ghj8phqmqr7y
While the WIP version is linked in the doc and the github readme, its not always obvious that you probably want that version
AYou mean a printscreen of the debug window? Isn't that the same as the samples.csv? Sorry for being a noob..
A
T@walmis Hello. I think the F03 motor I purchased is DOA.
CGot it thank youi
TI turned off my system and swapped with the F04 and it gave all the expected readings on the left panel. Also twisted the axis and showed movement.
TWhen I switched back to this F03 motor, this is what I get
T
T
WCan you check the motor IDs?
Thold on
T
WSo yeah, this one is with Pitch id
WYou need to disable X and enable Y in the configurator
TWorking now! Tyvm!
T
TBTW, is there any information concerning the date when we will be able to preorder/order the FFB kit for the MFGs pedals?
MLast news was late Feb due to a parts shortage on the bigger motors, so hopefully any day now
CLooking to get an extension cord for my vkb adapter. Not sure what type of cable it is. Any help?
WIt's a GX12 cable
MHi, a few weeks back, I set up VP Force config with some differing profiles for various modules. I had this working nicely, so when I flew the F14,. it loaded my F14 profile, the F5 , the F5 profile etc. However, it now appears to have stopped working.....Telem FFB does not register the correct module on the GUI anymore for example, I just flew in the Hornet and Telem FFB b was saying it was an F14.....it appears stuck on F14....any ideas what might be going on and how I might be able to unfuck it? Thanks! I have checked and in the system/edit sim section, each jet has the correct vpconf file selected at the bottom.....
Ncan you create a support bundle (help menu) and post that here, or post your userconfig xml file? Sounds like maybe you have an overzealous match string set up
Also a screenshot of TelemFFB when you are in a aircraft like the F18, but TelemFFB is loading the config for the F14
Also a screenshot of TelemFFB when you are in a aircraft like the F18, but TelemFFB is loading the config for the F14
CHey @walmis I just received a 2nd rhino order near completion message, I must have been signed up twice somehow. I wanted to know that this 2nd order could be cancelled and pushed out to the next lucky customer.
MSure, just had a look but could not find the xml file....can you point me?
S