the pedals will have their own control board, so this is completely separate from your stick and it'
the pedals will have their own control board, so this is completely separate from your stick and it's pot control
Sif you set your settings like this, you can do it all in one window. And then click on the logo JOYSTICK to switch
Ait would be helpful if I knew what those connector types were so could try to source some
Aor even more helpful if you could get an adapter with the kit
TYeah, I get that if you just use the pedals' control board, the brake signals would do what they had always done. I was asking about using the two analog inputs on the VPForce USB board for brakes.
MAs long as whatever sensor you're using is analogue, sure. Those sensor input points are just looking for a measurable shift in electrical signal (like a pot). If you want to do something more complex, you'd need to setup a shift register or breakout board, and code it to emulate a joystick that the Rhino board can run
T:). I get that too. My specific question was asking whether one could use the pot input on another VPForce board to globally apply FFB effects strength across two or more VPForce boards. So if I used the two analog inputs on my FFB pedals for brake signals, could I use the pot on my stick VPForce board to adjust force strength on the pedals.
MLike via a hardware link? You could wire the pot to both boards via mutual connections as long as the pot has the throughput to send signal to both. That would be a super annoying wiring setup though. In software, that should be pretty easy though
TIn software.
DJust a quick, general question. I have a TM F-18 grip in the Rhino…. It feels like something is loose in the grip itself, near the base the grip has a tiny, clicking movement. It is not noticeable when going side to sides only fore and aft, right near where the twist collar is. Anyone know how I should tighten it up?
MRemove the grip, and repeat the motions with it disconnected, see if anything moves that shouldn't. There's not a lot going on in the base area. Maybe the grounding screw came loose? You can crack the shell and see if anything is loose in it. The TM hornet is much more forgiving than the viper as far as springs and stuff flying out at you
DThat is what I thought, there is not a lot going on in that area of the grip. Thanks, I will try that.
PAmazing addition. Slaw RX Viper V3 next please!
II went from 36th to 6th today after I paid my invoice. This is just after I went from like 80 something to 40 something. Is that just all the people who passed up their reservation?
MHeck yea. I also jumped after paying my invoice. 4 to go!
SSo, I added my name into the hat for the rudder FFB conversion kits, how do I view the list for that?
MIt's pretty common on Warthog/Cougar for the tailstock to get a little loose. One of the screws is accessible from outside but the other is inside so it needs to be opened up to tighten it and I can see they carried this design over to the F18 grip.
DThanks!! I shall take a look.
B
Cpretty crazy that Walmis has already cranked out 70 Rhinos since I got mine. He's really ramped up the production big time!
Byea i originally figured september at the rate it was going earlier
Bi was originally assigned #618
B6 month wait for me
II was initially assigned 638, now I’m 475
II’m right behind Bozo
SNext 4 gang assemble (am behind ice) 
SOh damn crosswind preorder? Alllllmost tempted
BThis makes me want to ask, have any of you changed the trim button on the TM F18 grip for an Otto Controls one? If so, how hard was it and is it worth the hassle?
V:package: 
RHINO #0470 Has Shipped!
RHINO #0470 Has Shipped!SLets go boooozoooo
V:package: 
RHINO #0471 Has Shipped!
RHINO #0471 Has Shipped!SLets go iiiiice
SThoughts on mounting the Rhino to the chair vs the desk? In the context of no fixed cockpit setup, both options would be removable for home office work.
SI fear it will be too heavy for center-chair-mount, more so for swapping out rather than durability.
MThere's an old forum post floating around of someone who did. The center depress won't work unless you sacrifice another button somewhere, and you have to widen the mounting hole and jury rig it a lot
Opedals
BDo you mean the castle swith depress? The trim is a 4 way switch, no depress.
MThe trim is a 4 way on the hornet, it's a 5 way on the Eagle, and the switch itself is from Otto is a 5 way
MED Forums
Thrustmaster mods --------------------------------------------- F/A-18C (Hornet) grip upgrades OTTO P1 push buttons | OTTO T4 trim switch | OTTO T5 sensor control switch F-16C (Cougar) grip upgrades OTTO P1 push buttons A-10C (Warthog) grip OTTO P1 push buttons | OTTO T4 trim switch | OTTO T4/T5 ...
M2 more hype!
BIs it? I didn't know that. Thanks for the link! I'm toying with the idea of it but not decided yet
MGood luck, finding a used one is not easy, and they are like $400USD new lol
B
II wish, but mine is still 4 away. I should have clarified a bit
IOnly a few more days though!
SJust got my Rhino and thinking of ways to mount it to the next level racing Boeing seat. Looked through search but didn't find any answers..anything have a good solution?
Cthose of you using TM grips with your Rhino, what extension are you using? Preferably one that's in stock somewhere?
SSearch QR4RIGS. Loads of different mounting solutions that suit lots of different rigs.
S@Skood interesting, never heard of that but will give it a look.
Still looking for anyone who have a good solution for a NLR seat.
Still looking for anyone who have a good solution for a NLR seat.
RThingiverse
It's free, but feel free to donate/tip if you like what you see, thank you!
https://www.paypal.me/defnot4beer
Check this also https://www.thingiverse.com/thing:3580027
Ps2 connector https://www.aliexpress.com/item/32827138560.html
Added 180-250mm versions for makis2811
Added 390-400mm versions for Gregkar
https://www.paypal.me/defnot4beer
Check this also https://www.thingiverse.com/thing:3580027
Ps2 connector https://www.aliexpress.com/item/32827138560.html
Added 180-250mm versions for makis2811
Added 390-400mm versions for Gregkar
Thingiverse
50 / 75 / 100 mm extensions for Warthog and Virpil joysticks.
They should be printed with supports over 65 deg to avoid supports in the threads.
14/05/19
Added versions with 15deg grip twist to the left.
They should be printed with supports over 65 deg to avoid supports in the threads.
14/05/19
Added versions with 15deg grip twist to the left.
AHas anybody modified their rhino base to give freedom of movement along all four corners? I have noticed that my rhino has pretty restricted movement in each corner, making simultaneous full elevator and aileron deflection impossible