One more dumb question now that I am back flying helos, I have the WW Skywalker pedals, what should
One more dumb question now that I am back flying helos, I have the WW Skywalker pedals, what should my pedal option be in the Special Control menu?
IThe Apache definitely needs pedal trim unless you have no springs on the pedals
II use central position mode for the pedals
FHonestly i disagree, using pedal trim makes it hard to control when you remove trim
FWhen it jumps to the new position youll sway pretty bad
INot if you use central mode. When you click the trimmer, it holds that spot until you recenter the pedals
IIf you used instant it would
IBasically you click the trimmer, the pedals are locked into that spot until you physically recenter your pedals IRL
DThe pedals can either have a spring or no centering spring.
IFor helos, no spring would be best then you don't have to worry about pedal trim
DOkay, I am definitely going to have to practice to get used to flying with no spring in the pedals, but this is making me super excited for the upcoming helos.
DHoly crap! I cannot stress how much I have been missing in the FFB experience with this one simple fix of making sure the axis were not inverted in the configurator. It is a whole new game! Amazing, simply amazing.
TMan…. I’m going to be searching all your posts when I start hitting some walls.
This stuff is like golden because some of this set up stuff honestly got ya boy scared a little bit
Won’t admit it naw but yeah for real…
This stuff is like golden because some of this set up stuff honestly got ya boy scared a little bit
Won’t admit it naw but yeah for real…
TSo DCS curves arent compatible with FFB? Im assuming there's a similar option in the telem software or whatever ?
MThanks, I'll have a look
Nnot just DCS curves, but curves + FFB in general. If you think about what would happen when the center is no longer [0,0], it no longer makes sense. It also isn't feasible to try to move the curve with the center position.
In MSFS, where we are in full control of the axis position via TelemFFB, we support axis scaling/saturation.
Unfortunately in DCS, setting the saturation results in the same divergence of axis [x,y] versus FFB (physical) [x,y] across the range of an axis.
📃general
In MSFS, where we are in full control of the axis position via TelemFFB, we support axis scaling/saturation.
Unfortunately in DCS, setting the saturation results in the same divergence of axis [x,y] versus FFB (physical) [x,y] across the range of an axis.
📃general
MNice design, do you use a maintenance free self aligning bearing?
Tgood point. saturation curves work well when a stick is centered with springs after a trim, but it doesnt make sense with a force trim staying in position
MNo they are ball bearings not spherical bushings. They have 2 rows of balls and the outer race is dished so they can deflect off-axis while carrying radial loads. These things
MI see. In theory you need to grease these once in a while. I wish these existed as sealed bearings
MWait, they do exist
. This might work for me. Thanks!
. This might work for me. Thanks!MYeah sealed ones exist just not in the size I need so will either running them dry or with periodic lubrication
H@walmis I have a question about the TPR rudder pedal set. Do you have any plan in the future to add force feedback to the TPR? I would like to know? I am telling you many people want this.
PAnd the slaw device viper 3
Rsee knowledge base
Rits already been done if you want to follow DIY plans
Hthank you and I will take a look
V:package: 
RHINO #0517 Has Shipped!
RHINO #0517 Has Shipped!V:package: 
RHINO #0518 Has Shipped!
RHINO #0518 Has Shipped!
BRHINO #500, signed!
SWelcome in your new home 0510 
F511 has arrived ^^
Fdo you guys use native ffb for the dcs f14 or telemffb?
BFor the DCS Av8B flyers here, does your Rhino wobble left to right after engine start? And it then gets progressively stronger if you let it. Really strange
Fdid you try with a different plane?
Fsounds like you need to tune your damping/spring forces
BEhm, not noticed it on other planes but let me try again and get back to you.
BRecalibration needed?
FNo, more damping/less spring force
FSpring/damping systems are finnicky to get stable
FTry default settings in the configurator first, if it persists try looking in the #
support channel, there have been more people with a similar problem
support channel, there have been more people with a similar problem
AI am doing something wrong. Trying to map the Rhino in IL2 and the game does not react to movements in the stick. any idea?
SNever had that issue with the Harrier
F0515 is here…siri play halo theme
Nits pretty easy to over-do dampen/friction/inertia and create an oscillation loop. if you post screenshots of your configurator effects and settings tab in #support we can look and see if anything looks suspicious.
support we can look and see if anything looks suspicious.BOk thank you. I'll get those done tomorrow.
SWow just wow. Tried by now Mustang, Flanker, Warthog C, Tomcat, Strike Eagle, Harrier, Fulcrum, Hornet... was expecting how trim works on all planes but still positively surprised how well it is now reflected with default stick settings. I didn't even had to calibrate that thing. I think guys already have done it before shipping it to me. Thx!
JHello , i did just try the new OH6 Mod and there is « no match « in Telemffb . Does someone has an idea ? Every other helicopters work perfectly . Thanks !
NYou’ll need to create a new profile in TelemFFB when you load it (big purple button). But you’ll need this updated export script first. https://discord.com/channels/965234441511383080/1230852705593851964/1235261252306206740
JOk ! Many thanks will try that .. 
JOk new script past but when I launch telemffb i have no more the purple « create new profile « .. and no match again .. any clue ?