First time it hits you in the nuts you will be fine with it not being 60 foot lbs on the grip.
First time it hits you in the nuts you will be fine with it not being 60 foot lbs on the grip.
TUnless thats what you’re into…
Kink shaming… from you of all people.
Gosh
Kink shaming… from you of all people.
Gosh
BI do know some people.
Its not a party until someone is chained up and hanging from the ceiling.
But that's for a very different discord.
Its not a party until someone is chained up and hanging from the ceiling.
But that's for a very different discord.
Fmine sling shot forwards when I stuck the skids of the Huey into the ground a bit too much.
immediately decreased the effects after that
immediately decreased the effects after that
FDefault value of decell effect should be lowered
F
LI'm not sure that 3D printed plastic gimbal can handle great forces for a very long. So, be careful what you wish for 
BBeen readjusting the height and setup of mine so I could get a more comfortable position.
This did eventually wind up having it lower and closer so I load up the huey the other day and as I click fly it snaps back and whack me in the D.
I'm buying a left handed mouse so I can keep my right hand on the stick.
This did eventually wind up having it lower and closer so I load up the huey the other day and as I click fly it snaps back and whack me in the D.
I'm buying a left handed mouse so I can keep my right hand on the stick.
BPower supply question: What voltage should i set on my MeanWell LRS-350-24 using the adjustment? Lowest i can set it is 20.6V. Searching the discord i'm reading replies saying a 24V power supply is also fine. How does this affect the recommended Max PSU current setting of 7A? Can i turn it to 24V and get more forces before reaching max psu current?
HCan the bigger 86F04 just be exchanged from the smaller motors (from a software and logic board perspective) or do they need software adjustments?
WThey're fully exchangeable from the software perspective
HCool! They will probably rip apart the 3D printed gimbal I assume.... but I keep it in mind for future DIY projects. TY
WCan anyone speak to the longevity of the motors? Seems like the fans are kicking on after a few minutes of intense flying, is that to be expected? Looks like the y-motor fan is kicking on as it was over 45 C. Obviously the higher the gain settings, the hotter the motors. But should we be aiming to keep the fans off? Is there a temperature we should target to keep the motors from breaking down?
Afrom what I can tell there is a temp that is dangerous, but it's very high and the motors reducing max power makes it very hard to reach
Afans starting up isn't dangerous
WOkay good deal, I don’t plan on doing constant dogfights with all the effects blaring
WBut, I have noticed the fans kicking on during testing. Wasn’t sure if that was to be avoided, very good to know the power draw is reduced to keep the temps in order.
AI did a test with the instant action dogfight in DCS trying to see what happens if you really push the rhin
Ao
Ait got very boring at one point when it became clear that at the power level it was running the temps just wouldn't go up anymore
Rdoes the winwing F-16EX grip and all inputs work with the VPforce Rhino base?
H@walmis sorry, yet another question: are the motors from your kit, even though they are marked pitch and roll, interchangeable?
Fafaik, as long as you have 2 it wont be a problem to use the pitch motor for roll axis
Fhowever, you cant use 2 pitch motors or 2 roll motors
Fone of those combos might work, the other certainly wont, cant remember which
HCan you tell why that is?
FI believe the rhino needs a specific motor
Feither pitch or roll, forgot which
Fi've heard some people that had only one for ffb pedals needing to flash different firmware onto the motor cause the rhino didnt like the one it had
HI see…still not sure, if I understand why though. Maybe @walmis can add to this. Thank you meanwhile!
Aas for winwing stuff; I don't have personal experience, but I think the 16ex should work except for the vibration motor
Anote that there is an adapter you need to get for winwing
Fmy understanding is the program looks for a specific ID on the motor thats connected to it
Fif the ID it needs isnt there it wont work
Fif you have 2 motors it isnt a problem as youll always have X and Y
Fbut if you have only 1, which might be X or Y, only one of which will work
NMotors are encoded as X or Y
Ports on control board are agnostic
Motors can be axis swapped via firmware tool or Configurator software
Joystick must be 1 each X and Y axis
Pedals must be X axis
Collective must be Y axis
Each device must be discrete VPf control board
Ports on control board are agnostic
Motors can be axis swapped via firmware tool or Configurator software
Joystick must be 1 each X and Y axis
Pedals must be X axis
Collective must be Y axis
Each device must be discrete VPf control board
HGot it. Thank you both!
SHello I had a bit of trouble flying the F4 anyone have some settings and profile that works good with it and settings within dcs?
SHaving trouble with forces and trimming the f4 properly , always jumping around +-5000vvi with one click
TTry this, with roll 150 Pitch 250 in the DCS/Special/F-4 option. WIP.
DCS_Joy_F-4E.vpconf6.55KB
DCan anybody tell me what is needed to use a Virpil grip with the Rhino? I am in the process of building my Rhino base and would like to purchase a Virpil VPC Constellation Alpha or VPC Constellation ALPHA Prime to go with it. Is the Virpil just a plug and play add on? Do I need special thread adapters? Do I need special circuit boards?
PVirpil should be plug & play m8
Pno adapter needed. VKB & Winwing need adapters VKB being a pass through to the VKB black box
DIf I am not mistaken some other sticks require you to have their base off to the side. Is that not necessary with the Virpil?
DThank you!!!
E16ex works for sure. I'm using it. I have actually even wondered if the vibration motor works too. I just don't know how to separate rhino and 16ex vibration motor to test it
EBecause it feels to me like the winwing vibration motor is working too
TVirpil plugs in and works great with no external nothing.
Using a T50CM
Using a T50CM
TI’m gonna look at these thanks for sharing!
V:package: 
RHINO #0552 Has Shipped!
RHINO #0552 Has Shipped!