Curious for anyone else to try these settings... Gain map will cause the forces to ramp up quicker

Curious for anyone else to try these settings... Gain map will cause the forces to ramp up quicker (meaning the force should be higher overall at slower speeds). Artificially increasing your calibrated Y axis range does sacrifice some throw, but acts as a saturation which decreases the overall sensitivity....

Seems to be working pretty well for me (but I'm probably not the best judge either

)

HrEple•5/28/24, 6:22 AM

Ill have a look the following days. Thanks a bunch for the suggestions! I’m still so horribly new to this so fucking around takes a while.

NNumber481 Curious for anyone else to try these settings... Gain map will cause the forces...

Kowalsky•5/28/24, 9:24 AM

I've done exactly that and Pitch axis is slightly less twitchy, thanks for the

VPforceBot•5/28/24, 9:46 AM

:package:

RHINO #0554 Has Shipped!

VPforceBot•5/28/24, 10:06 AM

:package:

RHINO #0555 Has Shipped!

NNumber481 Curious for anyone else to try these settings... Gain map will cause the forces...

Hazzer111•5/28/24, 10:18 AM

I'll try this later hopefully, sorry the image appears to be really compressed so can't make out any of the settings. I might be being daft as well but I thought those settings in vp force were overridden by the sim?

HHazzer111 I'll try this later hopefully, sorry the image appears to be really compressed s...

Number481OP•5/28/24, 11:35 AM

the gain map is persistent.

FFierce_Fire Engineering takes time, and people have been asking quite often so dont be surpr...

Daz_bike•5/28/24, 12:09 PM

With all due respect, the picture shows the design and 'engineering' are complete. The items are listed on the pre-order and appear to be fairly basic. The design is the real clever part using the excellent VPforce motor kit. Some indication of an estimated timeline to release would be appreciated. i.e Q3/Q4

NNumber481 Curious for anyone else to try these settings... Gain map will cause the forces...

Snooper•5/28/24, 12:14 PM

The thing is that in the real thing the forces are low at low speed(pitch axis).

SSnooper The thing is that in the real thing the forces are low at low speed(pitch axis).

Number481OP•5/28/24, 12:24 PM

Yes, IRL the forces are much weaker at low speeds. But with HB's implementation, this effectively ends up with a virtually dead stick at low speeds with all things default. This is simply trying to maintain some semblance of centering force at lower speeds.

Seven•5/28/24, 2:11 PM

Should the stick in the F4 move with the trim?
Only way I achieve this is with enabling hardware force trim. Don’t have to this in the Viggen or the F14.

Bozo VFA-86•5/28/24, 3:36 PM

Hmm..my rhino moves with f4 pitch trim

NNumber481 Yes, IRL the forces are much weaker at low speeds. But with HB's implementation...

Red Magic•5/28/24, 3:39 PM

Does it have difficulty centering when released?

RRed Magic Does it have difficulty centering when released?

Number481OP•5/28/24, 3:52 PM

to some extent yes, but I still maintain that their bobweight simulation is too sensitive around nominal 1G, or the aircraft G output is too twitchy, or both. Its the same issue the TelemFFB g-effect has on some aircraft that are very pitchy. Its not an easy problem to solve.

Duchess ✈•5/28/24, 4:35 PM

Thanks for all the suggestions guys. The plane is still just barely flyable with my Rhino. It has a constant and continuous pitch up that I have to counteract with full nose down trim, even then if I take my hand off the stick it pitches up. I have changed my settings to reflect some of the ones that have been suggested and the stick feels “better”, still not at all like a real plane, but as I have understood it, the F-4 has a particular artificial feel to it. Since it does not seem to be a problem with the HB software, I can only surmise that it is a problem either with my VPForce hardware or my software settings.

NNumber481 to some extent yes, but I still maintain that their bobweight simulation is too ...

Hazzer111•5/28/24, 5:21 PM

From a look on the ED forums I see there is quite a bit of discussion about the FFB and get the impression that heatblur don't want to change it. But you are right, the bonus with the way telem handles things (and the way dcs really should) is that these effects are able to be tuned and tweaked.. Although I have a feeling that won't be done anytime soon.

The gforce effect in telem is definitely smooth in it's implementation, plus is can be turned down if it feels too rough. I certainly ended up pulling too much yesterday due to the g force effect reducing slightly and then increasing again

SSeven Should the stick in the F4 move with the trim? Only way I achieve this is with e...

Seven•5/28/24, 7:45 PM

I inverted the Y axis in FFB settings in DCS and the trim works in the F4

Stryker990•5/28/24, 8:02 PM

@walmis can we get a firmware update to add those virtual buttons on the Winwing F-16 stick soon pretty pleeeease? :funnyanimalsdog:

NNumber481 Curious for anyone else to try these settings... Gain map will cause the forces...

CapnFlint•5/28/24, 8:57 PM

I get the Spring Mapping force curve to get higher force at lower speed, but why did you do the +200 / -200 on your calibrated Y axis range?

CapnFlint•5/28/24, 8:58 PM

Is there a way in the VPForce software to set a minimum output force like has been suggested that Heatblur implement?

CCapnFlint I get the Spring Mapping force curve to get higher force at lower speed, but why...

Number481OP•5/28/24, 9:01 PM

its a way of decreasing the saturation of the axis, similar to what you can do in DCS axis tuning, but without jacking up the FFB. It basically makes the physical throw of your axis only move the virtual axis %80 or so, decreasing the sensitivity overall. If you find you regularly need that last %20 of elevator throw, it may not be useful.

CapnFlint•5/28/24, 9:04 PM

Oh gotcha, that makes sense

CCapnFlint Is there a way in the VPForce software to set a minimum output force like has be...

CapnFlint•5/28/24, 9:04 PM

I guess setting the gain map like this would get me something similar to ramp up the minimum force earlier?

HHazzer111 I'll try this later hopefully, sorry the image appears to be really compressed s...

GarrafaBr•5/28/24, 9:16 PM

It shows compressed during visualization only (when clicking the image), use saving/downloading then open with another program, the image gets its real resolution and you can see all the settings

HHazzer111 From a look on the ED forums I see there is quite a bit of discussion about the ...

Red Magic•5/28/24, 10:34 PM

I understand why they wouldn't want to change it, or the forces between simulated and in the stick don't proportionally match

Red Magic•5/28/24, 10:37 PM

And then that goes into the territory of giving false interpretations of aircraft handling. Similar to ppl with normal spring gimbals cranking axis curvature up

Bozo VFA-86•5/28/24, 11:01 PM

anyone experiencing runaway left aileron trim?

RRed Magic I understand why they wouldn't want to change it, or the forces between simulate...

Hazzer111•5/29/24, 7:16 AM

True, however they do allow the alteration of the gain, which when increased results in a disproportionate increase at the high end compared to the low. Would be much better if it was a linear increase and not an exponential one in my opinion

HHazzer111 True, however they do allow the alteration of the gain, which when increased res...

walmis•5/29/24, 7:24 AM

From physics perspective the force (=dynamic pressure) increases with the square of the speed, so it's correct that it's non linear.
edit: Although the F-4 implements an artificial feel system and is not directly coupled with the control surfaces, that may not be the case (haven't read the docs about the F-4 control stuff yet)

VPforceBot•5/29/24, 8:51 AM

:package:

RHINO #0556 Has Shipped!

VPforceBot•5/29/24, 8:56 AM

:package:

RHINO #0557 Has Shipped!

Boggy•5/29/24, 9:47 AM

Has anybody here ever had the trim button being stuck? I've had it a few times now and can't quite figure out what is causing it. I'm using the TM F-18 grip and sometimes the trim seems to go to full deflection, usually just the roll trim but today I also had the same happen to the pitch trim. I checked my keybinds and there are no double bindings. Dcs control inputs isn't showing that the button is depressed so I'm not sure what's going on. Could it be a button issue? An issue with the Rhino maybe?

BBoggy Has anybody here ever had the trim button being stuck? I've had it a few times n...

walmis•5/29/24, 10:00 AM

Which aircraft?

Boggy•5/29/24, 10:01 AM

Av8b

Boggy•5/29/24, 10:01 AM

But I had some roll trim issues in the F5 as well

walmis•5/29/24, 10:03 AM

The button glitches would appear as a erratic flickering if it were the case. But as I've noticed an increase in trim related issues recently, maybe a DCS update introduced some kind of bug

walmis•5/29/24, 10:03 AM

🧰support

Wwalmis The button glitches would appear as a erratic flickering if it were the case. Bu...

Boggy•5/29/24, 10:25 AM

Interesting. What that guy described is exactly what I had. I managed to fix it by pressing the trim button in all the directions a lot and the runaway trim disappeared.

Wwalmis From physics perspective the force (=dynamic pressure) increases with the square...

Grover•5/29/24, 11:49 AM

100% correct. And actually the bellows system make it like ^2 of airspeed. So it's almost dead while stationary - just the friction forces are keeping it from falling

Grover•5/29/24, 11:51 AM

this is a plot of the pitch forces during take off for the F-4B (the system is almost the same with some changes to the viscous damper and some additional springs - both removed in tge later models)

Grover•5/29/24, 11:51 AM

this is for 2 units nose down

Grover•5/29/24, 11:52 AM

check how little force change is required between neutral and full aft < 120 knots

Grover•5/29/24, 11:53 AM

and then for high performance turns, sufrace level, 8.5 G, you can have gradients as 6-8 lbf / G -> so forces around 50 lbf

Grover•5/29/24, 11:55 AM

And when you realise, that you don't need full deflection for that 50 lbf, you'll see that the gradients change by a factor of 25-100 from stationary to dogfighting

Grover•5/29/24, 11:56 AM

And then you realise that for the aileron it's something like 14 lbf (off the top of my head) for full deflection, flat - so doesn't depend on speed.

Grover•5/29/24, 12:04 PM

And finally, the default way a DCS module can communicate with any FFB stick is by providing the neutral position and force gradient multiplier. Through my tests, I found it limiting as nice feel required high gradients, but that caused signal clipping. However, sky is the limit, and we will see what we can cook to make more data available to the Rhino and make it more accurate.

GGrover And finally, the default way a DCS module can communicate with any FFB stick is ...

Number481OP•5/29/24, 12:26 PM

Just wanted to say thanks for jumping in here. Its always nice to hear directly from module developers and good things usually come from open conversations. I don't think anyone wants HB to sacrifice realism for the sake of one specific FFB device, but in my experience so far, it seems the realistic force curves don't translate well into the force range that the average FFB device can produce. There aren't a lot of FFB devices out there, and maybe I should dust off my sidewinder to see if the behavior feels different, but I imagine the general feeling would be the same across pretty much any FFB device.

Again, thanks for chiming in!

AndyHill•5/29/24, 12:36 PM

I think it's just amazing how much effort blur put into ffb considering how niche it is

Grover•5/29/24, 12:36 PM

Absolutely they don't, and that's why I bumped the roll forces up by some factor long ago (long ago - that's why I don't remember the precise value). OTOH, the toolset that we have is a bit limited. But finally, I think it also requires a shift in expectaions and understanding of how the devices work. For example, with driving wheels, it's much easier, because most of use drive cars. I know that sport cars have different feeling and you can't compare sport cars with everyday cars directly, but at least we (racing sim users with no real life racing experience) have some sort of experience to which we can refer. With flying, we come from being conditioned by decades of using spring-centred sticks, and it's sometimes very distracting and if feels awkward when a stick is almost numb - I mean no reaction. For example, we like a nice centre detent because it makes us feel reassured that we have no deflection etc, while in real life 'no deflection' is a bit more abstract, because everything is much less precise - for example the aircraft is a bit crooked and requires some constant aileron input.

AndyHill•5/29/24, 12:38 PM

how about the other stuff in the F-4 control options, I think there's at least an option for limiting maximum force the pilot can use or something like that

Grover•5/29/24, 12:39 PM

And I'm sharing all these thoughts because on so many occasions I had to re-evaluate my previous understanding when working on the F-4E, that I'm no longer the same person

Curious for anyone else to try these settings... Gain map will cause the forces to ramp up quicker

Similar Threads

Similar Threads

Similar Threads