Hi pilots! I've finally finished configuring my Monstertech setup and my Rhino sits proudly in the

Hi pilots!

I've finally finished configuring my Monstertech setup and my Rhino sits proudly in the center! Thanks @walmis for this extraordinary work and thanks to all those who work on the software! You guys are amazing!

I really encourage you (hum hum) to read the manual carefully as it contains a multitude of little details that will solve your questions! I made the mistake of not doing it right away, and it took me quite a while! After reading it (re hum hum) I was able to configure everything optimally! What an incredible slap in the face! It's really amazing!

Many thanks to you!

VPforceBot•6/17/24, 8:54 AM

:package:

RHINO #0583 Has Shipped!

DDracks Hi pilots! I've finally finished configuring my Monstertech setup and my Rhino...

PlaguedRoo•6/17/24, 10:46 AM

Cool! Can we see how your rhino is mounted? More pics! Also, how are the honeycomb products mounted?

PPlaguedRoo Cool! Can we see how your rhino is mounted? More pics! Also, how are the honeyco...

DracksOP•6/17/24, 11:29 AM

Thanks for the comments, I'll send some photos later!

I can already tell:

Rhino with the Monstertech plate (the photo will show it well but you have to be very very low! The 20cm extension is a bit long for me...the 10cm a bit short...so I took the Z (10+5cm = ok but it didn't look great with 2 extensions...)
Honeycomb Bravo => I took the monstertech side support, and the plate for the TM Airbus throttle (I put it at 90° so that it holds well).

The photos are coming!

joleobee•6/17/24, 11:44 AM

Any chance there’s a group buy coming up for the Rhino motor kits?

Jjoleobee Any chance there’s a group buy coming up for the Rhino motor kits?

Touch_Of_Legend•6/17/24, 12:09 PM

Kits are sold on an individual basis.

Just sign up and grab it!

DDracks Thanks for the comments, I'll send some photos later! I can already tell: - Rh...

Touch_Of_Legend•6/17/24, 12:10 PM

I love this set up as well and I love the Virpil covers! Might need something like that myself it’s sweet

TTouch_Of_Legend I love this set up as well and I love the Virpil covers! Might need something li...

DracksOP•6/17/24, 3:01 PM

Thanks ! Here's some photos ! Yes yes I still move something

DracksOP•6/17/24, 3:01 PM

DDracks Click to see attachment

SamNFTY•6/17/24, 3:10 PM

I see you still have your Virpal installed. What do you use it for?

DracksOP•6/17/24, 3:18 PM

Mainly for the Fenix A320 on MSFS. But I'm not convinced... all the joysticks seem bland since the arrival of the Rhino! But I love my Honeycomb Bravo so I'm trying things out !!!

DDracks Click to see attachment

Touch_Of_Legend•6/17/24, 3:36 PM

Yeah man are those panel covers lazer cut? They are awesome I love how you’ve got everything set up

TTouch_Of_Legend Yeah man are those panel covers lazer cut? They are awesome I love how you’ve go...

DracksOP•6/17/24, 3:42 PM

It's from https://www.deathdonkyprints.com/

DeathDonky Prints

Custom. Made affordable. Your 3D printing and Laser etching professional. #1 place for Virpil Control Mods.

DracksOP•6/17/24, 3:43 PM

The boss is amazing, kind, full of patience !! The price is OK

DracksOP•6/17/24, 3:44 PM

I forgot but the led are awesome !! I post some night pictures later

Reed•6/17/24, 4:10 PM

What side angled mounts are you using for the button boxes and the keyboard.

RReed What side angled mounts are you using for the button boxes and the keyboard.

DracksOP•6/17/24, 4:29 PM

It's all from Monstertech. a) MTS Keyboard side and B) the Monstertech VPC control panel Mount (side) =>https://www.monster.tech/en/product-category/mts-en/

MTSIM – MONSTERTECH

MTS Flight / Racing Cockpits – MTSIM – MONSTERTECH

FarFutureFox•6/17/24, 8:24 PM

Turbulence (in MSFS): how do you increase its effect? I don't see any turbulence setting in either the config app or VPforce. I already have turbulence set to realistic in MSFS. In my Brunner FFB software I have a setting for it, so I hope I just can't find it...?

nubbins•6/18/24, 7:38 AM

anyone else using the vkb adapter with the metal connector upgrade finding it's tearing up the threads?

nubbins•6/18/24, 7:39 AM

vkb adapter threads just fine onto a nylon connector as well as a PLA z-extension, but hates the metal connector, haven't been using it because I'm scared to

Nnubbins vkb adapter threads just fine onto a nylon connector as well as a PLA z-extensio...

walmis•6/18/24, 7:52 AM

That's strange, but you can find the ring stl here, if needed, to print here: https://discord.com/channels/965234441511383080/1198547200058347670/1252245760293208115

Wwalmis That's strange, but you can find the ring stl here, if needed, to print here: ht...

nubbins•6/18/24, 7:54 AM

usually printed in PLA?

walmis•6/18/24, 7:56 AM

I print those with PLA+ currently, but you can try PETG

VPforceBot•6/18/24, 9:19 AM

:package:

RHINO #0584 Has Shipped!

VPforceBot•6/18/24, 9:29 AM

:package:

RHINO #0586 Has Shipped!

VPforceBot•6/18/24, 9:29 AM

:package:

RHINO #0585 Has Shipped!

DirtySanchez228•6/18/24, 4:05 PM

Hello folks, is there a good setup for DCS and the rhino? i had some strange behavior when using the ffb function in dcs. when flying the f14 everything was working as intended. jumping into the f18 there was no real center at the stick and the plane was rolling and pitching the whole time. now with the f4 i disabled ffb in dcs and in the rhino software and use it as a "normal" base. maybe someone can send me some settings for the rhino software and dcs?

MashedPotato•6/18/24, 4:22 PM

If you had no centering with the hornet, that's a dcs bug, happens sometimes with ffb, with any module. Restarting the client usually fixes it. The hornet's ffb implementation is decent. The F-4s is pretty bad unless you tune the fuck out of it

DirtySanchez228•6/18/24, 4:25 PM

ok, thx for the feedback.

Swan•6/18/24, 8:56 PM

Hey guys - I'm approaching single digits in line. Is there any accessories I'll need to buy that will go along with the Rhino. I think there's a thing that limits the range of motion. Thanks

AndyHill•6/18/24, 11:14 PM

there are throw limiters, yes, I'd recommend getting some (or building some yourself once you've had the chance to try the rhino out and figure out what kind of limiters you need)

AndyHill•6/18/24, 11:14 PM

Also what grip are you planning to use? Some require adapters, some don't

AndyHill•6/18/24, 11:15 PM

also I believe there's a metal connector piece or something like that for the grip attachment, I'd look into that especially if you intend to switch grips from time to time

SSwan Hey guys - I'm approaching single digits in line. Is there any accessories I'll...

theProduceBroker•6/19/24, 12:05 AM

I'm with you. Just got my email and I wasn't expecting it for months if not years, lol

theProduceBroker•6/19/24, 12:06 AM

I've got a WinWing F-16 stick, so I added the adapter. I have a 3d Printer, do I NEED to order limiters or anything that I can't print?

theProduceBroker•6/19/24, 12:07 AM

How I will mount It I have no idea yet, so i'll poke through here for ideas. Full 6dof, actuator based rig w/ a RigMetal Ultimate.

AndyHill•6/19/24, 12:08 AM

limiters are very simple things and I think the files should be available

TtheProduceBroker I've got a WinWing F-16 stick, so I added the adapter. I have a 3d Printer, do ...

Number481•6/19/24, 12:20 AM

If you have a printer, parametrically adjustable throw limiter link is here: https://discord.com/channels/965234441511383080/1092338475795238962

NNumber481 If you have a printer, parametrically adjustable throw limiter link is here: htt...

theProduceBroker•6/19/24, 12:27 AM

Cool, thanks!

TtheProduceBroker How I will mount It I have no idea yet, so i'll poke through here for ideas. Fu...

Touch_Of_Legend•6/19/24, 9:15 AM

Mounting the Rhino is a project in its own haha

TtheProduceBroker How I will mount It I have no idea yet, so i'll poke through here for ideas. Fu...

nubbins•6/19/24, 9:46 AM

rigmetal is 4080-based yeah? monstertech has a plate, and walmis also has a similar plate available in the order form

Nnubbins rigmetal is 4080-based yeah? monstertech has a plate, and walmis also has a simi...

theProduceBroker•6/19/24, 10:09 AM

Yup - so this plate will work for floor mounting (feet area) on the RigMetal (it's 4080 based, standard extrusion)

-C1hhefO6WowUYc86k4h8GhuajHM97fErUoYc3JScO03stuox0RAM3NArrdN05SDNJjRGsKt6WY0FVs0-b9VMkAr22qsoOZ3Rgd9gSHotxulkhY6pDOMkwtdD1KyKxA4jQw260.png

theProduceBroker•6/19/24, 10:09 AM

What about the machined aluminum grip mount. Needed or worth it?

Ml5GT8fIbsRWWCV_c5gXC4LqvbyjM9xd7rkgt0epaAnTAhKrIqxqoZpFrqPsMxCLvcKOMDi30trRcH-xTcfaKc4Xt8k-WK76O1WFxO2xoA_FP8AV3Aax3HLBHX43V0OWlAw260.png

theProduceBroker•6/19/24, 10:10 AM

About to finish my order for the invoice

theProduceBroker•6/19/24, 10:10 AM

What does it do better, lol

walmis•6/19/24, 10:12 AM

Some people prefer metal, for durability, when changing grips often. I personally haven't had issues with the stock ones. Just don't cross thread the stock one and it will last forever

theProduceBroker•6/19/24, 10:15 AM

Ahh.. i'm a one grip kinda guy

theProduceBroker•6/19/24, 10:16 AM

theProduceBroker•6/19/24, 10:18 AM

Order placed

Wwalmis Some people prefer metal, for durability, when changing grips often. I personall...

theProduceBroker•6/19/24, 10:21 AM

I'm excited! Boy those 500 units in front of me sure went fast...

theProduceBroker•6/19/24, 10:22 AM

47 Rhinos to go!

Hi pilots! I've finally finished configuring my Monstertech setup and my Rhino sits proudly in the

Similar Threads

Similar Threads

Similar Threads