Sounds like a controls binding issue in your sim. Double bindings perhaps?
Sounds like a controls binding issue in your sim. Double bindings perhaps?
OShould I delete the button configuration I’ve chosen ?
Is that what you mean.
Is that what you mean.
HI can‘t help you in detail, since you are using a different sim than I do. But I would start with checking the axis bindings or anything related to pitch and roll. Delete any binding you don’t intend to use.
JI bought a motor for pedals and I've connected the usb and communications line from the motor to the controller card and plugged in power and usb. I'm connected based on the message at the bottom of the screen, but I dont see any position information coming from the motor. I must be missing something...any ideas?
J
OI’m using msfs 2020, I’ll have a look tomorrow after work.
Thanks.
Thanks.
Sdisable Y axis
S
Jlike magic:) thank you
P
Pit is not center aligned what can I do ?
HI think most people use some kind of extension, which in most cases can be rotated freely. Also with a center stick you usually want the grip in an angle towards your right hand to have an ergonomic wrist position. Of course I can’t tell how it works out for your needs, The only solution I can suggest is some kind of extension.
POkay. is it normal? or mis printed?
Pi think is too much off centered
Pif all guys have like this, I am okay.
KYes, this is correct angle for a center mount.
DOn my Rhino, it's the same as yours. But you can turn your stick to suit your needs. In any case, validated with my Virpil Alpha.
PThanks
P
Pwhich side do I need to mount motor?
Pis it right?
WThat should be the pitch motor
Pi got it thanks
Pdirection is right?
Psticker on top
P
Pmotor 1 is roll, 2 is pitch?
DTurn your gymbal 180
Pwhy?
PI already fixed all cant do that
HThe gimbal arm sides with the nuts in them must be on the faces with the motors and the cable outlet should face towards where the PCB is mounted.
Pgot it.
P
Pit is so hard, is it correct side?
Pok I will fix them all again
Pbecause it is actually 180 turn
TYep I have some pics that show but you must be careful with the orientation of the slot in the gimbal
You’ll get it the best part of DIY is that it doesn’t matter if it goes wrong you just take it apart and fix it.
DIY is forever basically because when you build it… you can rebuild it!
You’ll get it the best part of DIY is that it doesn’t matter if it goes wrong you just take it apart and fix it.
DIY is forever basically because when you build it… you can rebuild it!
T
TYep this is correct you can see in the pic above the correct orientation and yep this is correct how you said it.
OAny idea how to sort this. I’ve deleted all of my button settings. I’ve just downloaded some profile for it, but it’s not got anything other than the stick being central.
Sthe way the stick 'jumps' onscreen points to some other axis binding in msfs conflicting. what other peripherals are plugged in? also what aircraft is this? dont recognize it.
OIt’s the flight design , I’ve got my FFB rudder pedals , keyboard, V3 motion rig, warthog throttle and the PICO.
It doesn’t do it if I remove the stick and plug the stick base in.
It doesn’t do it if I remove the stick and plug the stick base in.
Syou mean the grip itself?
OYep.
It worked fine before I had the Rhino.
I’m so shit at these things
It worked fine before I had the Rhino.
I’m so shit at these things
Scan i see your msfs controls settings in a few screenshots. also in telemffb, go to help menu, create support bundle, and paste that file here
OI’m out now, to be honest I don’t even know what telemffb is, I was hoping that it was just plug and play for the money.
Thanks for trying to help but I’m going to have to pay someone to do it for me.
Thanks for trying to help but I’m going to have to pay someone to do it for me.
Stelemffb is required for it to do anything in msfs. download this and install. https://vpforcecontrols.com/downloads/TelemFFB/VPforce-TelemFFB-20240705.zip
run it when running msfs. remove ANY axis (pitch roll rudder) binding in msfs.
run it when running msfs. remove ANY axis (pitch roll rudder) binding in msfs.
OI shall try it tomorrow.
Thanks for your help.
Thanks for your help.
TThe VP Force configurator is a “set up, calibrate, and Keybinds” software.
It does control the main effects but they are generalized.
Telemffb is the software you set the various effects “per game” and “per module”.
So you tell Telemffb you’re playing DCS and it pulls info from DCS while it’s running and using that data it produces “effects” that you can set the strength and intensity of.
Telem saves the profile and now everytime you fire up DCS and jump in the Jug (p-47) the screen on Telem says “DCS” and says what module your flying “p47” and it will play the effects, at the intensity, you previously set OR that are just streaming in from DCS.
I assume it’s somewhat similar for MSFS but I haven’t tried the Rhino with MSFS.
Others for sure have so it works I’m just trying to explain what and why you want to use both the configurator AND Telem and keep them both open while you play.
(Minimize them or whatever)
It does control the main effects but they are generalized.
Telemffb is the software you set the various effects “per game” and “per module”.
So you tell Telemffb you’re playing DCS and it pulls info from DCS while it’s running and using that data it produces “effects” that you can set the strength and intensity of.
Telem saves the profile and now everytime you fire up DCS and jump in the Jug (p-47) the screen on Telem says “DCS” and says what module your flying “p47” and it will play the effects, at the intensity, you previously set OR that are just streaming in from DCS.
I assume it’s somewhat similar for MSFS but I haven’t tried the Rhino with MSFS.
Others for sure have so it works I’m just trying to explain what and why you want to use both the configurator AND Telem and keep them both open while you play.
(Minimize them or whatever)
Sno need to keep configurator open.
A+1 to what smitty said (and also -- the configurator is only the calibration/firmware settings app, it does NOT provide any effects, only allows you to set limits/calibrations/gain maps/firmware level button configurations. It does not need to be running as its settings gets stored into the device, assuming you press Store Settings, a 2nd step after using Apply Settings). Also MSFS is very different than DCS because MSFS does NOT have native FFB support. It only works through TelemFFB, but also has some setup/requirements steps (definitely refer to the TelemFFB manual for setting this up, if you're not very savvy with computers and hardware, MSFS is the hard mode relative to DCS and IL2 for force feedback)