HThe gimbal arm sides with the nuts in them must be on the faces with the motors and the cable outlet should face towards where the PCB is mounted.
Pgot it.
P
Pit is so hard, is it correct side?
Pok I will fix them all again
Pbecause it is actually 180 turn
TYep I have some pics that show but you must be careful with the orientation of the slot in the gimbal
You’ll get it the best part of DIY is that it doesn’t matter if it goes wrong you just take it apart and fix it.
DIY is forever basically because when you build it… you can rebuild it!
You’ll get it the best part of DIY is that it doesn’t matter if it goes wrong you just take it apart and fix it.
DIY is forever basically because when you build it… you can rebuild it!
T
TYep this is correct you can see in the pic above the correct orientation and yep this is correct how you said it.
OAny idea how to sort this. I’ve deleted all of my button settings. I’ve just downloaded some profile for it, but it’s not got anything other than the stick being central.
Sthe way the stick 'jumps' onscreen points to some other axis binding in msfs conflicting. what other peripherals are plugged in? also what aircraft is this? dont recognize it.
OIt’s the flight design , I’ve got my FFB rudder pedals , keyboard, V3 motion rig, warthog throttle and the PICO.
It doesn’t do it if I remove the stick and plug the stick base in.
It doesn’t do it if I remove the stick and plug the stick base in.
Syou mean the grip itself?
OYep.
It worked fine before I had the Rhino.
I’m so shit at these things
It worked fine before I had the Rhino.
I’m so shit at these things
Scan i see your msfs controls settings in a few screenshots. also in telemffb, go to help menu, create support bundle, and paste that file here
OI’m out now, to be honest I don’t even know what telemffb is, I was hoping that it was just plug and play for the money.
Thanks for trying to help but I’m going to have to pay someone to do it for me.
Thanks for trying to help but I’m going to have to pay someone to do it for me.
Stelemffb is required for it to do anything in msfs. download this and install. https://vpforcecontrols.com/downloads/TelemFFB/VPforce-TelemFFB-20240705.zip
run it when running msfs. remove ANY axis (pitch roll rudder) binding in msfs.
run it when running msfs. remove ANY axis (pitch roll rudder) binding in msfs.
OI shall try it tomorrow.
Thanks for your help.
Thanks for your help.
TThe VP Force configurator is a “set up, calibrate, and Keybinds” software.
It does control the main effects but they are generalized.
Telemffb is the software you set the various effects “per game” and “per module”.
So you tell Telemffb you’re playing DCS and it pulls info from DCS while it’s running and using that data it produces “effects” that you can set the strength and intensity of.
Telem saves the profile and now everytime you fire up DCS and jump in the Jug (p-47) the screen on Telem says “DCS” and says what module your flying “p47” and it will play the effects, at the intensity, you previously set OR that are just streaming in from DCS.
I assume it’s somewhat similar for MSFS but I haven’t tried the Rhino with MSFS.
Others for sure have so it works I’m just trying to explain what and why you want to use both the configurator AND Telem and keep them both open while you play.
(Minimize them or whatever)
It does control the main effects but they are generalized.
Telemffb is the software you set the various effects “per game” and “per module”.
So you tell Telemffb you’re playing DCS and it pulls info from DCS while it’s running and using that data it produces “effects” that you can set the strength and intensity of.
Telem saves the profile and now everytime you fire up DCS and jump in the Jug (p-47) the screen on Telem says “DCS” and says what module your flying “p47” and it will play the effects, at the intensity, you previously set OR that are just streaming in from DCS.
I assume it’s somewhat similar for MSFS but I haven’t tried the Rhino with MSFS.
Others for sure have so it works I’m just trying to explain what and why you want to use both the configurator AND Telem and keep them both open while you play.
(Minimize them or whatever)
Sno need to keep configurator open.
A+1 to what smitty said (and also -- the configurator is only the calibration/firmware settings app, it does NOT provide any effects, only allows you to set limits/calibrations/gain maps/firmware level button configurations. It does not need to be running as its settings gets stored into the device, assuming you press Store Settings, a 2nd step after using Apply Settings). Also MSFS is very different than DCS because MSFS does NOT have native FFB support. It only works through TelemFFB, but also has some setup/requirements steps (definitely refer to the TelemFFB manual for setting this up, if you're not very savvy with computers and hardware, MSFS is the hard mode relative to DCS and IL2 for force feedback)
TNope it doesn’t provide the effects but it controls them.
If you turn them off in the config they don’t exist for Telem
Same as the pots will override whatever other settings you use.
For me I always run it all but I’m also ALWAYS messing with something… like I’m never ever set up I feel like lol
If you turn them off in the config they don’t exist for Telem
Same as the pots will override whatever other settings you use.
For me I always run it all but I’m also ALWAYS messing with something… like I’m never ever set up I feel like lol
TIf MSFS is hard mode for FFB I don’t know if I could even handle it hahaha
DCS and all the various gear and programs is already A LOT to handle for this old guy
DCS and all the various gear and programs is already A LOT to handle for this old guy
Seh, i dont know if its "hard mode", but telemffb is certainly doing a lot more work behind the scenes with msfs
Pweb usb firmware update button is not clicking l, it is connected
Panybody help me please
Pcurrent version is v1.0.16
Pis it latest?
WIf it's disabled, there's nothing to update
PThanks
PPPtesting now
Pso nice 
PThanks a lot, I have done it.
Fwhy do you have a mat with rocks on it in your room? 
HMy preorder is just about ready. Quick question. I'm running Brunner Anti Torque pedals. Is there any issue running the Brunner FFB & the VPForce Software simultaneously?
Pbecause of motion simualtor,
PWithout it, the machine will press down on the floor and leave marks.
Pah sorry, I misunderstood. the rocks haha. for feet massage
LIs there 3 screws or just the 2 which are visible without removing the belt? See, the problem not only returned but it spread to X-axis 
Too much F-4E lately 
I guess?
2 mm is the smallest hex I found, but it's not an L-shape (I think it came with Stecs) and I can't get it inserted properly with the belt on.
Too much F-4E lately I guess?2 mm is the smallest hex I found, but it's not an L-shape (I think it came with Stecs) and I can't get it inserted properly with the belt on.
HTake the belt off then…
There are multiple holes, but usually you only need one screw, because there is only one flat face on the shaft.
There are multiple holes, but usually you only need one screw, because there is only one flat face on the shaft.
BWhat add ons do I need for vkb stick?
H…just to be safe - the screw goes against the flat face of course!
XNOTE: do not order those fancy black pulleys from ali, the quality is pretty bad compared to Zn
SCan I purchase the stoppers separately? I already have the base but now in hindsight I realize I should’ve purchased the stoppers with the base
MHi, I have a query regarding my newest Rhino ( I have 2) - its only 1 few months old and gets lightly used as a Helo cyclic base only. I have noticed a few times now, it suddenly turns the fans on full blast, when I have not been been using it....like just now, which prompted me. The PC has been sat idle, downloading the Afghanistan map and the update for 3 hours or so and yet suddenly, the fans come on for about 2 minutes full blast...and I have not even used it today! Is this right?
HI would pull up the VP configurator and have a look at the temperatures. The fan should only start if the temp goes above 50 C.
When you have your Rhino powered and for some reason it‘s vibrating (can happen when the gains and low pass filters are mismatched) I could imagine that it will slowly warm up….. but thats very theoretical and probably unlikely
When you have your Rhino powered and for some reason it‘s vibrating (can happen when the gains and low pass filters are mismatched) I could imagine that it will slowly warm up….. but thats very theoretical and probably unlikely
WYeah, I'd check the telemetry output, what are the motor currents at idle? Maybe it's configured to balance a heavy stick/extension, it will def heat up over time.
WYeah, ofcourse - the usual way via order.vpforce.eu