Have you tried pushing down the connector hard to make sure it’s seated? A lot of times it seems the
Have you tried pushing down the connector hard to make sure it’s seated? A lot of times it seems the pins just need a little extra to make contact.
VHi. What does it: new privat slash command -mean?
Spretty sure it's these
BJust another way to talk to the bot.
BWith the info command followed by your email you get a bit response with how it's going, only you will actually see those messages so don't worry.
AHi, couldn´t use my rhino for a long time. Now there is a new firmware.(I´m still on 1.0.15) but I cannot download it. (not in chrome nor in MS edge).
DIn a nutshell:
You need to configure your Rhino (1st software) then DCS (important because it natively manages ffb). Then run telemffb, which gives you the effects for each plane/helicopter. Most of them are directly recognized.
After that, you're left with the little details (which will take some time).
- You have the configuration software
- you have the effects software (telemffb)
- you've got DCS
You need to configure your Rhino (1st software) then DCS (important because it natively manages ffb). Then run telemffb, which gives you the effects for each plane/helicopter. Most of them are directly recognized.
After that, you're left with the little details (which will take some time).
DAnd after you go to the canal telemffb_user and learn a lot !
DSome users had posted chopper profile
1so i somewhat had it working, downloaded telemffb, downloaded a file from the #
knowledge-base and my stuff went crazy, tried to start all over agin with the first "center" calibration and now my figures arent near 2000, any ideas?
knowledge-base and my stuff went crazy, tried to start all over agin with the first "center" calibration and now my figures arent near 2000, any ideas?1
1Is there a setting to give more holding power at the central trimmed position? Looking for a more constant spring load as opposed to progressive.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=40)
[Adaptive Recentering is your friend.
![[OR] SerGeant](https://cdn.discordapp.com/avatars/290181622832168961/338cff3e564800fa5a1068e9c25e28f5.webp?size=16)
1Ummmm. It does help but that’s not what I’m looking for, unless I was doing it wrong…. Think of it as I’m wanting a preloaded spring feel, or a linear spring. Almost center detent like without the bump… does that make sense
[I get it. You don’t want a linear increase in spring load.
So you have to work with custom spring curves. Maybe someone can explain it better. I didn’t use that feature before.
So you have to work with custom spring curves. Maybe someone can explain it better. I didn’t use that feature before.
Mhello there, @walmis when you last requested i send in a video in the debug mode showing the twist grip values, were you able to view the video i sent, and is there anything more that is needed while you work on the latest update to the register size for the twist grip
HPut an additional point on the spring curve (symmetrical) and steepen the first part of the curve. That will greatly enhance the initial spring force right from the center (and increase the centering power).
Tmy rhino is no longer showing up in windows, but it is showing up in ffb configurator
Tany ideas?
T(and as a result not showing up in dcs)
T
Tahhhhh
Tok, if i disconnect my throttle, it shows up
Tobviously an issue with my pc - disregard!
T(or if anyone has any ideas on how to solve this)? all my devices are plugged into the one powered USB hub
TFixed it. If my logitech 502 mouse was plugged into the hub, it killed the rhino. Bizarre
1I finally discovered this! Only issue is the sick starts oscillating and vibrates if it’s too step, if I could get that sorted that’s what I was looking for!
AThank you, it worked
RYeah, I tried everything I could think of
RI've had to buy a virpil grip since that'll work out of the box
HDon‘t make the incline too steep or too big. And you may need add some dampening/friction to keep it from oscillating on itself.
[Hey, I got an issue with the y-axis motor. Inflight i just felt an uneven spring force for pull/push (pull weaker than push) It has 2-3 Amps difference for full pull and push. So it’s no imaginary feeling. My understanding of the software is, to manage the power output related to the springforce at a specific deflection?!
Also the X-axis feels more powerful at all at the same gain overall.
Defective motors?
Also the X-axis feels more powerful at all at the same gain overall.
Defective motors?
1How do the end stops work exactly? Is 100% the full range of the calibrated range or the 21/22 deg the rhino is capable of? Reason I ask is I was going to remove my 12deg limiter and use end stops to test different throw degrees….
MIm having trouble sourcing my own motor as the ones I've found either seem to have the no integrated drivers and they have different specifications than the ones on the vpforce website. Can anyone help me out?
Pif you plan on using any VPforce software you have to use the VPforce motors Walmis provides
Mwell i plan on using the same kind of motors, wouldnt that work?
Pno the vpforce motors have special drivers etc.
Moh damn
Pfor anti cogging & other stuff
Tmy Rhino stopped working suddenly this morning. Yesterday, it still worked. I dont hear this beeping sounds anymore when i turn on my computer. I checked if its the powersupply, but i get 24V on that board and also the motors have a green light. Anything else i can debug here?
Twhat exactly is triggering the beep sound? is it the power supply connected or the usb connected?
Tok problem seems to be the usb cable.. weird that it can just "fail" if though i dont move my joystick
TYep yep I’ve seen that issue before so great job troubleshooting
Whello everyone, someone could tell me which power supply should I buy to power the rhino vpforce, knowing that my connection is an XT60
XI'm on same boat, there are few "drone" charger ones with out of the box XT60, but they are 20V
The best Gold Standard from my understanding in Meanwell 350/24
The best Gold Standard from my understanding in Meanwell 350/24
XMeanwell is good power but big looks ugly and too much power for single unit, but it's best source you can get
XMeanwell LRS 350/24
to be exact
to be exact
TDROK 24V Power Supply, AC 110V/220V to DC 0-24V 20A 480W Buck Converter, Variable Adjustable Adapter Regulated 5V 12V 24V Volt Switching Voltage LED Transformer 20A Amp Charger for Computer Lab
Ti used this one