Yes, last time it was full nose down trim and that trim indicator was all the way at the top
Yes, last time it was full nose down trim and that trim indicator was all the way at the top
AI'll send it to you tonight after class 
NHmm. Yeah, thereβs nothing in TelemFFB that sets the trim. Even if you were using the hardware trim in the spring override feature, that doesnβt change the trim valueβ¦only the spring center.
I donβt even think itβs possible to externally set the trim in DCS.
Send over your Telem config anyway and Iβll have a look at it.
I donβt even think itβs possible to externally set the trim in DCS.
Send over your Telem config anyway and Iβll have a look at it.
AWonder if something in my DCS install is corrupted then because I even deleted the keyboard trim bindings just to be sure there was nothing else that could input
*Guys... did anyone design a plastic cover for the front cable & power connectors...?
I already stumbled over those protruding cables and it's gonna get wrecked if I do it again...
I already stumbled over those protruding cables and it's gonna get wrecked if I do it again...
KI turned my Rhino, so the connectors are on the backside.
Also you can buy angled usb & power cable/adapters. This helps, too.
I didn't see a cover for them here.
Also you can buy angled usb & power cable/adapters. This helps, too.
I didn't see a cover for them here.
Vso after adding force comp. my stick starts to oscillate on the x axis what can i do to go around that? i only get it when i put force comp im pretty new sorry the questions
PHi Guys how do i find my position in the que ..i found the bot to use ..i think ..not to sure what to type in said didnt understand ? new to the discords any help much appreciated .thx
HWould anyone happen to know how I've screwed over my config so bad it makes the joystick disconnect when I load into modules in DCS?
I was wondering if it was because I disabled hot swap in DCS, but apparently thats not it either. I have no other USB issues as far as I can tell.
EDIT I do have a B650 motherboard - AMD / 7800 X3D cpu.
I was wondering if it was because I disabled hot swap in DCS, but apparently thats not it either. I have no other USB issues as far as I can tell.
EDIT I do have a B650 motherboard - AMD / 7800 X3D cpu.
HJust by trying to load the default Rhino profile in VPForce FFB Configurator, I get this error log in TelemFFB - seems it disconnects
2024-10-09 21:22:04.535 - joystick - INFO - Launching VPforce Configurator....
2024-10-09 21:22:41.615 - joystick - ERROR - Exception
Traceback (most recent call last):
File "telemffb\hw\ffb_rhino.py", line 659, in timerEvent
File "telemffb\hw\ffb_rhino.py", line 787, in read_reports
File "telemffb\hw\hid.py", line 163, in read
File "telemffb\hw\hid.py", line 148, in __hidcall
telemffb.hw.hid.HIDException: hid_read_timeout/GetOverlappedResult: (0x0000048F) The device is not connected.
2024-10-09 21:22:41.615 - joystick - WARNING - Reconnecting HID device in 1s
2024-10-09 21:22:42.623 - joystick - INFO - HID connected!
2024-10-09 21:22:04.535 - joystick - INFO - Launching VPforce Configurator....
2024-10-09 21:22:41.615 - joystick - ERROR - Exception
Traceback (most recent call last):
File "telemffb\hw\ffb_rhino.py", line 659, in timerEvent
File "telemffb\hw\ffb_rhino.py", line 787, in read_reports
File "telemffb\hw\hid.py", line 163, in read
File "telemffb\hw\hid.py", line 148, in __hidcall
telemffb.hw.hid.HIDException: hid_read_timeout/GetOverlappedResult: (0x0000048F) The device is not connected.
2024-10-09 21:22:41.615 - joystick - WARNING - Reconnecting HID device in 1s
2024-10-09 21:22:42.623 - joystick - INFO - HID connected!
NProbably bad advice, since your issue looks to be different... but you can try this: π§°support
Otherwise you may need to wait for @walmis to help figure out the USB/driver issues.
Otherwise you may need to wait for @walmis to help figure out the USB/driver issues.
HMuch appreciated suggestion, Number481. Iβll try the script tomorrow.
WHmm, do you use a USB hub?
HI have a powered usb hub connected to the pc, but havenβt plugged the rhino into it. Tested it out as well yesterday with the same disconnect.
WDoes this disconnect happen only when using telemFFB ?
HI suspect so, yes. Iβll have a try with only using the config later on. But I suspect itβs only with telemFFB active.
WOne thing that could cause a reconnect normally is if the config profile changes either the "device ident" or the "device ID"
HIβm assuming that would produce a different usb product ID in the vpforce ffb configurator. Vaguely certain it stays the same, but also going to look into that. Any other way to tell if the configs force a new id?
NThis shouldn't be possible.. TelemFFB reads the config file first to check that the PID matches the device its getting ready to send it to.
WYeah, but device name change will def cause a usb reconnection
Ntrue.. we don't check for that. I guess I should also check the Ident against the
dev.product_string in addition to the PID check.
SHello everyone, I have just finished the mechanical construction of my diy collective and am trying to get the electronics up and running. I am experiencing the following problem. In the FFB Configurator I do not get a display of the motor position (see screenshot). I have connected the ID:0 (y) pitch motor to MOT 2. I have checked the power supply to the motor and it is OK. What have I overlooked? Any help is welcome.
Many thanks
Martin
Many thanks
Martin
Ndisable the x axis in configurator so it knows its a single motor setup
H@walmis @Number481 I just found something interesting. Some of the profiles I load changes the USB Device Ident from "joystick" to "Rhino" (for my helo build). When the ident changes away, the stick disconnects ...
SThank you but that does not change the problem
NOK. This is what walmis was saying. The Ident and PID must be identical across all the profiles for the same device, otherwise you will see exactly what you are seeing.
I'm extending the logic in TelemFFB that would have prevented you from assigning those profiles in the first place
I'm extending the logic in TelemFFB that would have prevented you from assigning those profiles in the first place
HIdiot-proof it, you say? 
TItβs not showing any input power to the controller board. Is your power supply connected and switched on?
NDo you also have a Rhino FFB Joystick connected? If so, (and even if not), you'll want to change the USB Product ID to something other than 2055, and change the name to "Collective", or something other than Joystick.
If you also have a joystick plugged in and they are both 2055, it won't work very well.
If you also have a joystick plugged in and they are both 2055, it won't work very well.
SThank you very much for your support. I just reinstalled the configurator and started just from the beginning and now it works - I am so happy. And I will change Device Ident and product ID acording your recomendation not to run into conflicts with my cyclic base.
Thank you and best regards
Martin
Thank you and best regards
Martin
RAny recommendations for new power supplies? The one that came with the unit is no longer working.
TJust to confirm - it looks like Auto Calibrate followed by Store Settings (and then exporting my config) only saves the calibration info to that config? Importing or loading other configs seems to restore my old calibration from before I put in limiters. Instead of redoing the Auto Calibrate for each of my 4 base configs, can I just copy/paste the related lines from the .vpconf file? It looks like it's just "x_angle_max", "x_angle_min", "y_angle_max", "y_angle_min"? Or is there a simpler method I'm missing?
TJust tried the cut and paste and that seems to work fine.
WHey, can you elaborate how did you come to that conclusion?
RUnit beeps when connectinf to usb along with green internal LED. Configurator showing motor 0 and motor 1 timeout. Checked ac input with multimeter and get 120v, output barrel measures 0v.
WYou can get an replacement, something like
https://www.amazon.com/Laptop-Charger-Gaming-GS63VR-GE72VR/dp/B09LYMJN9N/ref=sr_1_3?sr=8-3
It should be 5.5x2.5mm DC jack, 180W or more
https://www.amazon.com/Laptop-Charger-Gaming-GS63VR-GE72VR/dp/B09LYMJN9N/ref=sr_1_3?sr=8-3
It should be 5.5x2.5mm DC jack, 180W or more
This charger is compatible with the following models: GS65 Stealth SeriesοΌ005 004 007 002 006 483 478 296 GS65 Stealth THIN SeriesοΌ068 053 054 050 051 037 045 259 047 GS75 Stealth SeriesοΌ091 093 202 089 203 204 205 237 413 249 412 GS63VR STEALTH PRO SeriesοΌ001 002 034 078 041 068 674 229 230 469 ...
CIs there any way to have balance spring forces configured relative to position on the axis?
Drooping behavior is not the same at the axis extreme as it is in the center. Higher Balance Spring force makes the stick bounce back at the end of the axis, but is required for the stick to hold center at the center of the axis.
Drooping behavior is not the same at the axis extreme as it is in the center. Higher Balance Spring force makes the stick bounce back at the end of the axis, but is required for the stick to hold center at the center of the axis.
Cie I want a less springy force, and rather a more linear/flat one.
CNVM all this, but for anyone else searching I added some really small amount static force and that really nailed the feel of the stick. Now it feels perfectly balanced
CStatic force feels like a much better option for balancing this, surprised it comes in at the end in the manual and so few ppl talking aobut it in the discord when I was searching
TIβIβve been trying to do something similar w Balance Spring and Static Force, but havenβt got it dialed in yet. Could you post your numbers for those along with any extension length and grip type? Would help to have a reference.
CI was just about to say that I use a VKB Gunfighter grip in metal, no extension and stock Rhino
C
Wwhy does my rhino return to center after being pushed forward (without power)
it only does that after being pushed forward, if i pull it back or tilt it sideways it stays like that, but if i push it forward, it moves back to middle-ish position. It also happens with power on and no effects applied
happens with and without the grip installed, so it's not caused by it's weight.
DIY Built
it only does that after being pushed forward, if i pull it back or tilt it sideways it stays like that, but if i push it forward, it moves back to middle-ish position. It also happens with power on and no effects applied
happens with and without the grip installed, so it's not caused by it's weight.
DIY Built
CI might not even need the Balance spring at all at this point. But this is very very good for now
OI'm looking for a little help with the Mig-19 in DCS. The stick just flops around - I.e. there's no return force or any sort of "spring" effect on the stick at all
Any idea what I'm doing wrong?
Any idea what I'm doing wrong?
TI just did a quick test on the MiG-19 and I get "correct" spring and effects. In TelemFFB I see that it loaded my configurator file for the Jet class, and that it shows the plane matches "MiG-19.*".
I haven't updated to the most recent TelemFFB yet. New to Rhino so nothing else to suggest.
I haven't updated to the most recent TelemFFB yet. New to Rhino so nothing else to suggest.
NShould just work AFAIK (I don't own the 19)... other aircraft are working fine?
SI have 4 VPforce motors and two usb drivers which I now use for stick and rudder pedals (3 motors), can I purchase just one more usb driver to run the spare motor for a collective?
OYes - other aircraft are working fine. I can see that "Mig-19" is being matched in the Jet Class so I'm at a bit of a loss as to why
L@Cynemi
Hi .
Please ,I look your Setting-effect And I would like to test them too.
Could you show me your #Setting please
Thank you so much in advance/Laurent
Hi .
Please ,I look your Setting-effect And I would like to test them too.
Could you show me your #Setting please
Thank you so much in advance/Laurent