I was just about to say that I use a VKB Gunfighter grip in metal, no extension and stock Rhino
I was just about to say that I use a VKB Gunfighter grip in metal, no extension and stock Rhino
C
Wwhy does my rhino return to center after being pushed forward (without power)
it only does that after being pushed forward, if i pull it back or tilt it sideways it stays like that, but if i push it forward, it moves back to middle-ish position. It also happens with power on and no effects applied
happens with and without the grip installed, so it's not caused by it's weight.
DIY Built
it only does that after being pushed forward, if i pull it back or tilt it sideways it stays like that, but if i push it forward, it moves back to middle-ish position. It also happens with power on and no effects applied
happens with and without the grip installed, so it's not caused by it's weight.
DIY Built
CI might not even need the Balance spring at all at this point. But this is very very good for now
OI'm looking for a little help with the Mig-19 in DCS. The stick just flops around - I.e. there's no return force or any sort of "spring" effect on the stick at all
Any idea what I'm doing wrong?
Any idea what I'm doing wrong?
TI just did a quick test on the MiG-19 and I get "correct" spring and effects. In TelemFFB I see that it loaded my configurator file for the Jet class, and that it shows the plane matches "MiG-19.*".
I haven't updated to the most recent TelemFFB yet. New to Rhino so nothing else to suggest.
I haven't updated to the most recent TelemFFB yet. New to Rhino so nothing else to suggest.
NShould just work AFAIK (I don't own the 19)... other aircraft are working fine?
SI have 4 VPforce motors and two usb drivers which I now use for stick and rudder pedals (3 motors), can I purchase just one more usb driver to run the spare motor for a collective?
OYes - other aircraft are working fine. I can see that "Mig-19" is being matched in the Jet Class so I'm at a bit of a loss as to why
L@Cynemi
Hi .
Please ,I look your Setting-effect And I would like to test them too.
Could you show me your #Setting please
Thank you so much in advance/Laurent
Hi .
Please ,I look your Setting-effect And I would like to test them too.
Could you show me your #Setting please
Thank you so much in advance/Laurent
CAbsolutely,
everything here is just the default
everything here is just the default
DSo i've got cracking noises on my roll axis at high spring forces when i move the stick past a certain point to the left and the right. Found this message and removed the stick mount so i get access to the bolt like in this picture.
But how do i tighten it now? If i try to it just rotates the nut together with the screw (which makes sense i guess because there's no holding force on the screw).
Do i have to disassemble the whole thing or how do i do it? Or are there other possible causes of that cracking noise that i could check out first?
But how do i tighten it now? If i try to it just rotates the nut together with the screw (which makes sense i guess because there's no holding force on the screw).
Do i have to disassemble the whole thing or how do i do it? Or are there other possible causes of that cracking noise that i could check out first?
TIs it possible you just don’t have the Rhino axes mapped to pitch and roll for the MiG19?
OI think you may have meant this for me maybe?
I managed to figure out a solution. Flying without TelemFFB the stick was fine - felt normal.
As soon as I enabled TelemFFB and it matched the Mig-19.* profile the stick would be limp with no return force
I created a new TelemFFB profile for the Mig-19 by cloning (and tweaking) the F-5E profile and it's ok now
Something wierd in the original profile was causing this behaviour I guess
I managed to figure out a solution. Flying without TelemFFB the stick was fine - felt normal.
As soon as I enabled TelemFFB and it matched the Mig-19.* profile the stick would be limp with no return force
I created a new TelemFFB profile for the Mig-19 by cloning (and tweaking) the F-5E profile and it's ok now
Something wierd in the original profile was causing this behaviour I guess
HHi, has anyone a fix for my problem. Build a collective and an Rudder with the big 86BLF04 . First I had no FFB Effekts but the spring effect was perfect over the whole travel. No I changed the normal settings above, now I get FFB in Flight, but I have a big deadzone without resistance . Even Steps are not counted in that area. The dead zone is not in the middle, but at the position the collective or rudder is at the moment and you start the movement.
HWhen you have no position readings of the motors - have you checked the hardware? Maybe the pulley came loose on the motor axis.
HFor all I can say, wether the application FFB works properly or not. The raw readings in VP config should show the slightest movement.
NAt the risk of asking stupid questions…did you calibrate the axes in configurator?
HI did and steps are also at 2048 in mid position
HPiñon is perfect mounted at the motor. When power is of, cogging is in the full travel. Strange is that both devices has exactly the same behavior
HHmm, maybe check the gain map for issues.... other than that no ideas at the moment
IHey everyone, for the last few days I've had problems with my rhino in DCS, when either the roll axis or both are not generating any force. When I exit DCS it goes back to spring mode and becomes alive. Everything looks ok in the configurator, so it doesn't seem like a hardware/firmware issue, it's just in game. It used to just work, not sure what happened. I think the only thing I changed was the telemffb update.
Has anyone had similar issues?
Has anyone had similar issues?
NTo rule out any of the override features you may have inadvertently enabled, does the same happen without TelemFFB running? Remember that the spring effect is part of the native sim implementation, not TelemFFB.
NThe blue dot does not smoothly follow the axis as you move it through the range of motion? A short clip showing the configurator window as your moving the axis might shed some light.
Iyes, the same happens once I start DCS, with or without TelemFFB. What override features are you referring to?
NThere’s the general spring override, there are configurator gain overrides, etc.
Are you by chance using SimHaptic?
Are you by chance using SimHaptic?
INot using simhaptic.
The thing is I haven't changed anything in the settings recently, so I can't imagine it's related. I can only thing of either the telemffb update and dcs update
The thing is I haven't changed anything in the settings recently, so I can't imagine it's related. I can only thing of either the telemffb update and dcs update
NLike I said, TelemFFB doesn’t do anything with the spring and obviously if it’s not running, it’s not doing anything at all.
Did you double check FFB didn’t disable itself in DCS?
What specifically are you flying?
Did you double check FFB didn’t disable itself in DCS?
What specifically are you flying?
HTeleFFB is off and I have that problem. Blue dot is not moving when starting the movement until the Force starts. Pinion is perfectly mounted for sure. We are speaking of only the standby behaviour at the moment. In Xplane the deadzone is the same... I upload a video now. Feels like there is an encoder plate loose and giving no signal.... But on two motors and controllers at the same way. Independent Controller, independent Power Supply.
HHHNWhen you run the auto calibrate, does the dot move the full range of the axis?
HNo
HReseted Config… same Problem
HSorry
HPinions on Rudder and Collective were loose the same time 
HWhen Power was of, the cogging was on the complete travel, so I thought the pinions are ok...
NIt happens
Hsee 
that was an educated guess from experience!
that was an educated guess from experience!H20 Years of being a field service engineer teached me to be sceptical when an error is the same on two units.... But it learned me also never trust new spare parts.... even after changing two times , both spare parts can be broken :-9
Ithere's a "force feedback" checkbox in dcs, if that's what you mean. I tried both f-18 and f-16. The strange thing is that sometimes the pitch axis does work, without any changes to anything.
HThe Rhino is first a machine designed to shake itself apart and second a fun input device. 
The loose pinion gear wasn’t the last thing I had to retighten and fixate with loctide.
The loose pinion gear wasn’t the last thing I had to retighten and fixate with loctide.HOk, Now I understand the name "joystick"
BI mounted a couple of transducers to a recliner once for movie watching.
It was potent but cheap kit, it could make the 80lbs chair rattle across the floor like an old nokia phone would across a glass table.
With my 200lbs butt sitting in it.
And the chair was just shaken beyond function in a matter of months.
It was potent but cheap kit, it could make the 80lbs chair rattle across the floor like an old nokia phone would across a glass table.
With my 200lbs butt sitting in it.
And the chair was just shaken beyond function in a matter of months.
CHey all, I'm new to this joystick and having issues with the AH64. When I force trim it snaps the stick almost all the way to the right. I have the special settings to INSTANT TRIM and the pedals to WITHOUT SPRINGS AND FFB
CAh I figured it out. The "swap axis" box was checked, which inhibited it form working.
NAs a rule, to ensure a proper experience:
- Make sure the axes directions are set correctly in configurator such that the position dot follow the stick inputs correctly. This ensures that “FFB direction” and “axis direction” are in sync.
- don’t use curves in DCS axis settings
- don’t use saturation in DCS axis settings
HG'day @walmis , unfortunately my WinWing adapter snapped at the threaded collar.
Could you let me know how to get another or if there's an stl I can try to print a replacement.
#VPF-0702
Cheers.
Could you let me know how to get another or if there's an stl I can try to print a replacement.
#VPF-0702
Cheers.
H
P@walmis sorry to ping you, but just about to use my rhino in a dcs op first time since the recalibration you did. Is it ok for me to import & apply old config profiles or will that break the new calibration you did on the x motor?
