That would be greatly appreciated! It would save me a lot of work!
That would be greatly appreciated! It would save me a lot of work!
MI believe this is the file I used to replace the original arrow plate. You may need to slightly scale if it's too tight.
MWWAdapterConnector-mate.stl548.91KB
CThank you!
J"the virpil alpha and alpha prime have left hand variants" Do these fit the Rhino base out of the box?
(Hiya I have an issue I updated telem fb to latest version which then told me I needed to update rhino firmware which I did but now when rhino configuration starts I get an error saying incorrect version 182 expecting 181 or something similar firmware is v1.0.17b2
AYeah should have no problem working
RAny reason why vpforve is using 5.5-7.5% of my cpu?
R
RWhen I shut the program down, the cpu utilization in cpu 0,1,4,5,8,9 goes back to idle.
Rwhat is the normal cpu utiliation, do we know this number?
TI'm trying to fly the A10C II and am noticing that while force trim is working, I'm not feeling any vibrations in the stick. Is this supposed to vibrate when I shoot the cannon?
.yes, but you have to set it up in telemffb
TWhat are the steps to complete that? Is it like that for other aircraft as well? I fly the Tomcat and felt that the FFB was pretty good.
TTelemFFB is a separate program from the configurator that adds more forces than are native to the sim using telemetry exported from the sim. Download and install from here.
https://github.com/walmis/VPforce-TelemFFB/releases
https://github.com/walmis/VPforce-TelemFFB/releases
GitHub
DCS FFB Telemetry Effects (for VPforce FFB). Contribute to walmis/VPforce-TelemFFB development by creating an account on GitHub.
TThe documentation on how to use and install it is in the Rhino manual. Assuming you are flying DCS, there may be one additional step for the installation to get it going which will be in the manual.
WHaving issues getting the brake axis and twist axis to be recognized for the constellation Alpha. Raw Values don't change when either axis is turned. Thumbstick axes work fine. Any tips on how to debug? Latest firmware installed v1.0.17b12 @walmis @Red Magic
Red, did you do anything to fix this? Found some comments from you above.
Red, did you do anything to fix this? Found some comments from you above.
TI installed Telem FFB and now my game crashes to desktop every time I try to get into a plane.
TWorks fine if I close TelemFFB
WI think it's my stick. VPC's software can't see those axes either :/
WAny suggestions on a more robust stick?
KCheck Export.lua and disable other tools in there to check if there are incompatibilities.
TI'll check. Not sure if it matters but if I start TelemFFB after I'm already in the plane it works great. My DCS is a clean load too, just reloaded my computer yesterday.
TOnly thing I'm seeing in my scripts folder is SimHaptic and TelemFFB
MWill do thanks - thought I followed the steps, but perhaps left out the apply after calibration and unlink....
VIm having some trouble with the vpforce winwing adapter. The vpforce app detects the adapter when I select it, but all buttons on the winwing grip are constantly pressed and dont work. Suggestions?
MHi, OK, tried this again, and having similar issues I use a virpil Z extension on both my Rhinos, and when I have the stick at centre or forward of centre, I can adjust the negative balance spring value (approx 11%) to make it stay in a placed position. But if go backwards past the centre, then the stick wont stay where you put it - even at 100% negative..of course at this setting, once I place the stick anywhere past centre in the forwards direction, it snaps fully forwards.
MAnother thing I notcied on calibration ( but not in normal use) is that when you rotate the stick around the circle at full deflection, there are places where I am feeling a cogging ( forwards) and other places ( around 4 oclock and 8 oclock) where I can feel a notching....any ideas whats going on there?
M
MA video may a little large to post
Mand with my normal effects applied
HThe first screen shot you show the balance spring at -94% in the forward postion 6% in the positive but your 2nd screen shot your balance spring shows -11.1% and 0%..Your left and right is also changed. On my forward position I'm using 18% (positive number) and rear 5%, 12% on my left and 10% on my right. As for cogging this usually means the calibration ones done properly to full deflection or there is a mechanical issue.
CHey,
Outside dimensions are perfect but the inside hole for the din is way too big. Would you still have the CAD for this?
Outside dimensions are perfect but the inside hole for the din is way too big. Would you still have the CAD for this?
MSadly, I could not find my original openscad project, but I re-measured the original adapeter plate, and the inside diameter was 10mm, so I used 3D builder to fill the oversized hole, then put a 10mm hole with a slight chamfer as per the original plate. this should be much closer.
WWAdapterConnector-matev2.stl923.23KB
TSome of my planes in IL2 Great Battles the center is forward or the trim is acting very weird if I trim nose down the stick moves forward alot in order to keep plane level. I need to apply constant force down when doing so. But some of my planes do not act like this I'm using the same config profile for all right now. any thoughts? I notice this on the duck the spit and the p39 so far I know it happens on other but those are the ones I've flown recently.
Tit like trim is working but why is it having the opposite effect on the direction of my stick like this?
KDo you have configured curves in IL-2? This lead to the problem on my side.
Tno curves in IL2 at all
Nnot sure I fully understand your problem description, but if the trim movement seems to be backwards, in general I would recommend to make sure the dot in the axis view in the configurator app moves in sync with your joystick. If one or both axes are backwards, use the invert setting for that axis in configurator.
If your axis is backwards and you invert it in the game, this will usually lead to inverted forces since there is typically no sync between "ffb direction" and "axis direction".
If your axis is backwards and you invert it in the game, this will usually lead to inverted forces since there is typically no sync between "ffb direction" and "axis direction".
TI have turned my stick base around but I checked the invert on my pitch axis when I turned my base around. Is there another area I need to invert for trim to work correctly.
T
Twhat you are saying makes sense my stick works good for everything but when trimming plane out the stick moves the wrong direction
TI just don't know how to fix it.
Ndoes the purple dot follow the stick correctly and in the right direction?
Tyes the purple follows
Tits kinda weird when i trim out plane stick needs to be forward to stay level?
Tonly in a few planes
NI guess I misunderstood then? Thats how the trim effect works. If you trim down, the stick will move forward, same for other directions.. the center point of the spring effect will move in the direction you are trimming.
If nose down trim is required to maintain level flight, the stick will be forward of center.
If nose down trim is required to maintain level flight, the stick will be forward of center.
Tyes maybe these planes are just weird to me and the FFB is weird to me as well never used it before but some planes act different most planes i can trim out and stick stays in middle level flight few planes stick must be well forward in level flight while trim is 100
NI can't really help with what to expect from various aircraft in IL2, but that is how FFB trimming works in general. Various aircraft my implement it differently or not at all.