I've only tried in the Hornet. Small dead zone of one or two and add some curve. Fingertip pressure.
I've only tried in the Hornet. Small dead zone of one or two and add some curve. Fingertip pressure.
RThe 64 at least is very easy setup. With Telem program open and DCS too (sitting in the cockpit) you have sliders and options available to tweak what kind of feedback and how much you're getting. I recommend turning the ETL shake down, it's too violent by default.
For trimming the 64, use the DCS ingame trim button and not the VPForce one.
For trimming the 64, use the DCS ingame trim button and not the VPForce one.
RFor all modules make sure you calibrate the VP in the configuration program. Something like hitting the calibration button on the bottom, going through the sticks full range of motion, then clicking the button again
RVirpil and apparently thrustmaster grips run directly with the Rhino no issue. VKB iirc need an adapter
CDo you have this set in the VPForce software or in DCS?
![SR-F_Winger_[73]_David](https://cdn.discordapp.com/avatars/98037306870472704/f924b51d2e4486c1eb873c2f4fb7f6a3.webp?size=16)
MSent a DM!
CJust plug in do the initial setup and fly. tweaking you read about is optional.
![SR-F_Winger_[73]_David](https://cdn.discordapp.com/avatars/98037306870472704/f924b51d2e4486c1eb873c2f4fb7f6a3.webp?size=40)
Sanswered
![FuturPaladin [FR/2A]☨](https://cdn.discordapp.com/avatars/408735665916870657/1d7f7fb0842510dda4e1f46eeb26285e.webp?size=40)
FRead the q&a
CIs the calibration a global calibration, or do I have to recalibrate for each different plane config I’m using?
RThe calibration is global
Vhttps://www.youtube.com/watch?v=9HJYkbHFWwk
someone already saw this and maybe tried to put it on a vprhino?
someone already saw this and maybe tried to put it on a vprhino?
YouTubeCommand T
FFBeast: https://ffbeast.github.io/docs/en/joystick.html
Just Fly It YT channel: https://www.youtube.com/@justflyit7569/videos
Watch my full review of FFBeast Joystick Base:
https://www.youtube.com/watch?v=xtge1SGVlzA
Support me on Patreon & gain access to my mission .miz files:
https://www.patreon.com/command_t
---------------------...
FFBeast: https://ffbeast.github.io/docs/en/joystick.htmlJust Fly It YT channel: https://www.youtube.com/@justflyit7569/videos
Watch my full review of FFBeast Joystick Base:https://www.youtube.com/watch?v=xtge1SGVlzA
Support me on Patreon & gain access to my mission .miz files:https://www.patreon.com/command_t
---------------------...
ODCS - I'm still on waitlist for rhino
Mhow many days before estimated shipping do I get the offer to actually pay for my rhino?
Mim at less than 30 now and i'd like not to miss it (in case the email goes to spam or something)
BIt won't ship until you pay.
Wait to long, and it'll just go to next guy on the list who does.
Make sure you can receive pms for the bot, that was the first way i got notified.
Email came shortly after, that's more likely due to how slow email works.
Wait to long, and it'll just go to next guy on the list who does.
Make sure you can receive pms for the bot, that was the first way i got notified.
Email came shortly after, that's more likely due to how slow email works.
FThat was written in my notification mail to actually confirm the order when it was my turn: "Please note that if we do not receive your completed order form or a reply within 10 days,
this preorder will be considered void." After filling out the order form it took four days then I got a notification for payment. So you have about 10 days when receiving the first notification to place the order or get in contact with Walmis.
this preorder will be considered void." After filling out the order form it took four days then I got a notification for payment. So you have about 10 days when receiving the first notification to place the order or get in contact with Walmis.
LFor aerial refuelling a precise throttle is perhaps more important than the stick. I couldn't do it with any confidence until I changed to a better throttle.
ATo a degree, yep.
Going from TM 16k to VKB Gladiator was a day and night difference as well.
However, that was mostly due to the center spring being a pita in the center, where you do most of the movements for AAR.
Going from TM 16k to VKB Gladiator was a day and night difference as well.
However, that was mostly due to the center spring being a pita in the center, where you do most of the movements for AAR.
Gis there a step by step guide to connecting/configuring a VKB F-14 (IV) grip with the Rhino? I've got it setup (I think) in Configurator and Loopback correctly (though there was no instruction on how to setup the Pot 1/2 Source in Loopback that I found - I assume those are set to the Rhino - are both to be turned on? Slider to the right?)
In the VKB Device Config, it's showing as a Space Gunfighter XT2 - there are no other options.
The joystick itself is working great in DCS, but the buttons on the grip aren't recognized (DCS sees it as a Space Gunfighter as well - don't know if that's an issue).
I have the WinWing F-18 grip, and it's working perfectly when connected, but I can't figure out the VKB.
In the VKB Device Config, it's showing as a Space Gunfighter XT2 - there are no other options.
The joystick itself is working great in DCS, but the buttons on the grip aren't recognized (DCS sees it as a Space Gunfighter as well - don't know if that's an issue).
I have the WinWing F-18 grip, and it's working perfectly when connected, but I can't figure out the VKB.
SIf it shows as "Space Gunfighter XT2", then you need to flash the blackbox using VKB bootloader with the firmware compatible with the F-14 grip.
SSpace Gunfighter is the "Kosmosima" one
RAnybody using the "VPC Constellation ALPHA Prime"? I wonder how it is after using a Warthog for 10y now. I'd appreciate more buttons and axis, aswell as the movable handrest.
CYeah this was a surprise tip for me from my friends too! Once I set a slight deadzone on my Rhino and adjusted my throttle detent and throttle friction I finally got it.
Whello everyone, I have a question, I just realized that I have my old ender3 3d printer and I plan to recover the meanwell which is on it to power my VPforce is what I can do to power my VPforce only rn waiting for me to finish my diy rudder MFG?
KHow big is your Deadzone? I'm struggeling myself with finding the right size to master AAR with the Rhino.
DVery good quality, lots of buttons. Works perfectly with the Rhino
DI have mine since 2023 end no issue at all
CI did 2-3% with an extension
GThat was it, thanks!
DShould I contact vp@vpforce.eu if there is a problem with my order? I sent an email 4 days ago but no response so far
HThans for all the info and help to my previous questions, I have now picked up the Rhino of my friend, he has told me it has a F18 limiter in place and that I may need to get a limiter 3D printed that suits the Apache.
Where would I find the info on getting a limiter plate printed, I have a friend who could print one for me, 2nd question would be is there a std limiter that can cover most planes in DCS from warbirds, jets and helicopters, if so what that would be.
Where would I find the info on getting a limiter plate printed, I have a friend who could print one for me, 2nd question would be is there a std limiter that can cover most planes in DCS from warbirds, jets and helicopters, if so what that would be.
Hhey, quick question: Im getting within 30 days of my order being fulfilled and I dont remember what email I had on file for my reservation..would I get a message from the VPForce Bot when its ready?
![Prometheus [Prom]](https://cdn.discordapp.com/avatars/777496628579401739/90d1e9e0a05c7bafd59a74ba942bd870.webp?size=40)
Pyou should get a pm first here, might be worth checking with Walmis if you’ve change emails etc.
GStill having some VKB F-14 issues. It's mostly working. The weapons selector switch, however isn't. The toggle between Phoenix/Sparrow works, but none of the movement of the switch (up or down) registers.
Also, very weirdly, the trim hat works fine in the DCS controls setup, but doesn't operate the trim when I'm flying.
I've checked through my setup and I did order the correct Rhino VKB adapter (for MK IV grip), so I don't think that's it. I'm confused
All of the other buttons (and the DLC axis) are working fine - just the weapons selector and the trim hat.
Also, very weirdly, the trim hat works fine in the DCS controls setup, but doesn't operate the trim when I'm flying.
I've checked through my setup and I did order the correct Rhino VKB adapter (for MK IV grip), so I don't think that's it. I'm confused
All of the other buttons (and the DLC axis) are working fine - just the weapons selector and the trim hat.
OAny pc builders have advice WRT USB on motherboards? Building a new one for 5090 and considering how to support my sim rig better.
SIf you're using it for the DCS, do you need the loopback functionality ? I don't use it, so can't really help you there, but the weapons selector on the VKB grip is mechanically not a switch, but a magnetic encoder, if the loopback software gets raw data from the grip, then it won't work, as it needs to be reconverted by the VKB BlackBox.
CDon't bother using the loop back for DCS.
XHey, maybe stoopid question, but can you assign force trim push/release on different joystick?
for example f-trim for rudders on collective button
for example f-trim for rudders on collective button
FI would call that FFB
Jgenuine question - why are you replying to comments made a long time ago?
JThat was from back in August
Mguys, what are your solutions for powering the rhino? I understand that the power adapter is not included?
TIt is included
TUnless that has changed since I got mine
Ggot mine a few weeks ago - the power supply is included!
DHi Guys !! I'm going to receive my Virpil FLNKR Grip tomorrow! I'm ready to test it with our VPFORCE apps !
FStill haven't received any status update for my FLNKR order. 
DMe too but I had the surprise of getting DHL mail this afternoon 