WThat's the TLDR version, basically almost all games only control only the spring effect (center point and stiffness). Other effects can could be created from telemFFB - such as low hydraulic pressure effect for example.
Jnice work. are you planning to share the STL file?
Mif you want it, sure, its just a simple plate with a few holes
Mhole setup probably going to differ between your desired mounting solution and mine anyway
Mthe small holes are for the qr4rigs qruhd quick release base
Mthe large countersunk holes are to mount the plate to the rig profile below
M
Mgonna be something like this
Myellow is the qruhd base.
YCould you please explain this text and table in page 69-70 of the manual: Load aircraft with vpconf set at %80 and spring gain override congured at %40
○ TelemFFB pushes new vpconf
■ new gains are read and stored for later use
○ TelemFFB pushes gains from the override cong
○ The net result is that the gains on the device will be whatever is in the
override cong since it happens lastTelemFFB Congurator Spring Gain Override 80%
TelemFFB Aircraft spring gain x 40%
Final Force 75%
○ TelemFFB pushes new vpconf
■ new gains are read and stored for later use
○ TelemFFB pushes gains from the override cong
○ The net result is that the gains on the device will be whatever is in the
override cong since it happens lastTelemFFB Congurator Spring Gain Override 80%
TelemFFB Aircraft spring gain x 40%
Final Force 75%
YWhat is the net results here? 40%?
NThey are called "configurator gain overrides" in TelemFFB because you are literally overriding whatever gain slider setting you have in configurator. Setting these for an aircraft in TelemFFB is the equivalent of opening configurator and moving the slider to a %value and applying.
YIf I understand correctly, then what would make sense is to apply in the Setting slider always the same maximum value for all DCS modules, and let DCS set it up based on its own parameter. Am I understanding correctly? Is there anyway to know which is the value set by DCS? Is it always one value or can be a curve as well?
P@walmis I would like to ask about the Winwing adapter you offer. I want to use it to connect my WW grip to a Moza base. I know they are not compatible, so I want to run a bypass cable and plug the grip into the old WW base. I am only interested in a mechanical female to female adapter. I would use it to connect a male to female extension, drill out a hole in it, and run the bypass cable. Therefore, I need the adapter to not convert the WW cable to anything, but just contain a simple din6 extension. Or just to be hollow. I don't want the din6 to din5 conversion that the Winwing adapter contains. Would this be possible to order from you?
BIs it me or is the DCS F-4 a total pain to trim out nicely? It feels like the instrument trainer I used to fly in flight school 25 years ago, one moment you're flying at the right heading , alt and speed. Look away for a split second and it's in a 3000 ft/min dive. What the hell?! Am I missing a setting or something?
TFrom what I’ve heard that is working as intended. I don’t feel like I can ever get a level trim on that thing either. When it’s almost there even one tap of the button always overtrims
BExactly, it's really irritating. I've never flown a real airplane that was that hard to trim to fly level. The instrument trainer we had did behave like that and that was to make us better instrument pilots.
FYeah, same. Always fighting for trimming.
Maybe @Grover can give some insights how to set it up best?
Maybe @Grover can give some insights how to set it up best?
TI find it’s easiest to trim slightly nose down and then use some muscle memory to hold back pressure on the stick. Also, I like to use the altitude hold when possible, just be sure to bind master caution reset.
Sis the Rhino base physically compatible with SimFab DCS edition?
Slooking through past messages in this server I see reference to a custom mounting bracket, what issue does that solve (i.e. is the standard mounting bracket too tall or are the holes in the wrong locations, etc...)
RI do this too
RBut with helicopters
JAnyone's joystick just go limp in DCS? I'm getting no resistance whatsoever but I still get telemffb working
AI find it easier to trim when the adaptive recentering is off.
V:package: 
RHINO #0902 Has Shipped!
RHINO #0902 Has Shipped!V:package: RHINO #0903 Has Shipped!
RHINO #0903 Has Shipped!
TReally gives you another level of respect for the Blue Angels pilots who flew the F4 before the transition to F18’s.
Now of course they’ve transitioned again and they fly the Super’s.
But yeah formation flying in the Phantom….
Was seriously a next level skill.
Flying formation in a hornet is balls easy as compared.
Now of course they’ve transitioned again and they fly the Super’s.
But yeah formation flying in the Phantom….
Was seriously a next level skill.
Flying formation in a hornet is balls easy as compared.
EHi all, I just got my Rhino up and running, and everything works fine, but telemffb not working in DCS. Force feedback also enabled in DCS, and also tried the auto DCS setup in system setup. Anyone have suggestions? Also the Button/hat Source in Loopback not saving. Screenshot attached Thank you
EAllso tried the pot 1/2 in Loopback source to be Rhino but no luck.
BJust checking: But stick will be practically dead until you are in a loaded and started aircraft.
And any changes to configurator needs to be applied and stored to stick.
And any changes to configurator needs to be applied and stored to stick.
EStick works in DCS but no telemffb. Nothing shows in settings/master instance when i am in aircraft. I use "store settings" everytime i change anything in Configurator.
FMaybe the telemffb.lua is no bueno?
E
V:package: 
RHINO #0905 Has Shipped!
RHINO #0905 Has Shipped!V:package: RHINO #0904 Has Shipped!
RHINO #0904 Has Shipped!W@Eagle1 attach your dcs.log file and export.lua so we can take a look
EIs that file missing somewere?
EOk, just a moment
WI don't see references to telemFFB in DCS log. Probably the module isn't loaded. Can you attach the export.lua from Saved Games directory.
Also let's move this to #
telemffb-user to not clobber up #
general
Also let's move this to #
telemffb-user to not clobber up #generalEOK..Thank you
WHello everyone, I would like to know, I have just tested my rhino on DCS, what should I set to feel, for example, the vibration of the aircraft when taxiing, the stall etc...
Fyou need to run TelemFFB for those effects
Wah ok, I'll install it now.
YAnyone observing a different behavior since the last version? I noticed that the first time I get into a DCS module, it does not seem to always take the correct profile specified in TelemFFB. I have to open VB_Configurator and import and apply manually the profile, then it works ok, and then it seems to be able to switch profile correctly from one module to another, and work as well correctly for the rest of the day, each time I get into DCS. Does it have to do with how things are kept into the memory of the Rhino? Just wandering if it is my set-up or something that other people have been noticing since last update?
YAlso, for me the RhinoLoopBack does not seem to memorize yet correctly previous joystick assigned, although I thought it was supposed to be fixed in last version
ODoes the Rhino mount adapter connect to this Virpil thing
OAll my stuff is put away at the moment so I can't check
YI am keeping on having issue since the last update. In the middle of a DCS game, the Rhino stopped and told me that boot loader was detected. I started boot loader and it tells me to upgrade the firmware although the firmware was already up to date, I upgraded anyway. After, the update whatever profiles that I load in VPForce, the Spring force is null, although all this other parameters seems correct.
JI wouldn’t recommend just a clamp to the desk, but maybe someone who runs that can verify