What would the motor kit include? I have most of a printed propeler style gimbal but have it in piec

What would the motor kit include? I have most of a printed propeler style gimbal but have it in pieces as I've refocused on other stuff? I guess I'd need to print a fresh gimbal?

RRight Rudder - Left Stick What would the motor kit include? I have most of a printed propeler style gimbal...

walmis•5/20/22, 7:38 PM

You can use that gimbal! The motor kit provides two motors, wires to hook everything up and an FFB USB controller. It's a plug and play system, you only need to do basic calibration to get it running.

VVulkan More over about the base its self why do you think its the best on the market? W...

walmis•5/20/22, 7:39 PM

I'll get back to you tomorrow :)

Right Rudder - Left StickOP•5/20/22, 10:26 PM

do the motor kits include the hall effect sensors too?

Kapti•5/20/22, 10:48 PM

No need. The position is direct from the motors.

Wwalmis You can preorder a unit at the moment, I'm currently building a batch of 6 Rhino...

sko•5/21/22, 1:54 AM

Id like to preorder a fully built unit. let me know what i need to do.

KKapti Ill chime in real quick. A friend just ordered motors for a base we are working ...

Flashgod_VR•5/21/22, 5:05 AM

I also can chime in here. Walmis accomplished something on such a high quality standard on his own, where usually much bigger teams with higher count of individual professionals are needed. I was already extremely curious by the information he shared about the details, everything made sense "on paper" instantly. And after finally getting my hands on the Rhino, i was simply blown away.

FFlashgod_VR I also can chime in here. Walmis accomplished something on such a high quality s...

Otto•5/21/22, 5:14 AM

Both @.kapti. and I experienced the same. This truly is a giant leap forward into the simulation experience for the community. Hoping to make it affordable for many to enjoy.

Flashgod_VR•5/21/22, 8:28 AM

@everyone just wrote my first thoughts about the Rhino in the DCS FFB thread. some of you may find certain answers for your questions there: https://forum.dcs.world/topic/246873-honey-i-developed-ffb-joystick-diy/?do=findComment&comment=4973130

ED Forums

Honey, I developed FFB joystick (DIY)

Ssko Id like to preorder a fully built unit. let me know what i need to do.

walmis•5/21/22, 3:22 PM

You can DM me - Currently I take orders by creating an invoice through PayPal. For the Rhino I'll take a small deposit to confirm the order, and once it's ready before shipping we'll finish the transaction.

Fer•5/21/22, 6:46 PM

Hel @walmis what’s the cost, does it use winwing and virpil sticks ??

walmis•5/21/22, 7:01 PM

Hi @fer4705 , the price for the complete base is 800EUR, Virpil is supported (T50CM2 - fully tested, others will follow), WinWing adapter will be developed later.

walmis•5/21/22, 7:02 PM

You can also read the great review by @flashgod_vr here: https://forum.dcs.world/topic/246873-honey-i-developed-ffb-joystick-diy/page/17/#comment-4973130

ED Forums

Honey, I developed FFB joystick (DIY)

Fer•5/21/22, 8:27 PM

Thanks @walmis

f4l0•5/22/22, 5:35 AM

Hey @walmis ,

I'm the developer of SimShaker for Aviators, @flashgod_vr ask me to get in touch with you to discuss the possibilities to enhance the FFB experience with SSA data, or to help you, to get data from DCS...

I-WVoss•5/22/22, 5:39 AM

@walmis , Good morning!! Could I have the data to pre-order the full base? I already have Virpil T50CM2 with extension. Thank you!

II-WVoss @walmis , Good morning!! Could I have the data to pre-order the full base? I alr...

walmis•5/22/22, 6:37 AM

Good morning! DM me, I'll get back to you. Currently out of town for a bit.

Ff4l0 Hey @walmis , I'm the developer of SimShaker for Aviators, @flashgod_vr ask me ...

walmis•5/22/22, 6:43 AM

Hi there! Welcome! I'll DM you in a bit :)

The_Fragger•5/22/22, 2:23 PM

Hey guys

walmis•5/22/22, 2:23 PM

Welcome!

Flashgod_VR•5/22/22, 2:36 PM

@the_fragger

walmis•5/24/22, 6:09 PM

walmis•5/24/22, 6:09 PM

Received the shift register boards, gonna test them tomorrow

Otto•5/24/22, 6:16 PM

I'm going to need 2, soon

maxonly•5/25/22, 12:46 PM

Will the rhino be available as a kit or just fully assembled?

walmis•5/25/22, 12:46 PM

Hi, the Rhino will be fully assembled.

Wwalmis Hi, the Rhino will be fully assembled.

maxonly•5/25/22, 12:49 PM

Thnx, very excited about this project

walmis•5/25/22, 12:50 PM

My mission is to bring back FFB from the dead

AndyHill•5/25/22, 1:14 PM

that's a pretty worthy mission as far as I'm concerned

paulnd•5/25/22, 5:08 PM

I'm interested in using the motor kit for a 737 control column in P3D/MSFS, the most important part for me is to be able to simulate trim adjustments accurately and the 'heavyness' of controls - is this currently supported by the software or is further development needed?

walmis•5/25/22, 5:19 PM

I think it should be possible to simulate the "heaviness" using the inertia/damper/friction combination. Trim is also not a problem if the sim supports native FFB. I do not know how well P3D supports FFB, for MSFS, XPForce plugin should allow for pretty good FFB. The mechanics for the yoke should be interesting :) To summarize - out of the box experience should be pretty good and some improvements will be definitely possible to implement via firmware updates with your feedback.

AndyHill•5/25/22, 5:27 PM

did I understand correctly that the total cost of an operational unit would be closer to 1k€?

walmis•5/25/22, 5:29 PM

The motor kits are from 299€ to 439€, with mechanics it can come close to 1k definitely. The complete Rhino base is 799€ :)

AndyHill•5/25/22, 5:29 PM

and that doesn't include stick and power source?

walmis•5/25/22, 5:30 PM

+ 180W power source
- grip

AndyHill•5/25/22, 5:30 PM

I'm working on an article about controllers in the ~600€ range, but I'm going to also talk about the next step up and I'm very interested in FFB

paulnd•5/25/22, 5:30 PM

Are you aware if anyone has tested the motor kit with Prosim? controls communicate with Prosim and not directly with the sim, an interface may be needed to drive the motor kit. I assume that the software is for configuration only and doesn't need to be running?

AndyHill•5/25/22, 5:31 PM

I might want to pick your brains at some point to make sure I get my facts straight

AAndyHill I might want to pick your brains at some point to make sure I get my facts strai...

walmis•5/25/22, 5:31 PM

Sure thing

Ppaulnd Are you aware if anyone has tested the motor kit with Prosim? controls communica...

walmis•5/25/22, 5:35 PM

Not yet, this endeavor is in quite an early stage. I'm planning to implement an API to directly send requested torques to the device. That will open up many capabilities to interface external software with the device.
Yeah, the GUI software is a configuration front end, all the processing is done in device firmware.

Havebug•5/28/22, 8:34 AM

Hi @walmis , first of all great job! Flight simmers community really needed a FFB device! Since I'm quite proficient in mechanics and electronic stuff, I'm very interested in buying the Kit. Can you please recap of what is included in the kit and how I can buy it?

Flashgod_VR•5/28/22, 8:37 AM

i think those photos in the showcase tab show it all (scroll up). you'll get 2x modified motors (with implemented sensors) and the main controller

Havebug•5/28/22, 8:39 AM

yes, I noticed there are two motors and a controller, but in another picture I see a different motor size... So was wondering if is there an option to order different types of motors...

walmis•5/28/22, 8:39 AM

Hi @eaf51_havebug ! Yes the motor pictures are featured in the showcase. The whole thing is plug and play, you only need to attach motors to your mechanics and calibrate axis range.

walmis•5/28/22, 8:39 AM

walmis•5/28/22, 8:40 AM

Here are different specs for the motors according to manufacturer.

walmis•5/28/22, 8:41 AM

and the prices:
57BLF kit: 299€
86BLF03 kit: 399€
86BLF04 kit: 439€

walmis•5/28/22, 8:45 AM

The kit includes: 2 motors, USB FFB controller, hook-up wires for quick start (you may need to lengthen them, etc to accommodate your design)

Havebug•5/28/22, 8:46 AM

and i gues on the controller theres a connector for the Virpil Grip? (removed from the original base?)

walmis•5/28/22, 8:48 AM

There's a 5 pin JST XH connector on the board for TM, Virpil, WinWing grips

Havebug•5/28/22, 8:51 AM

Perfect, thank you. One more question: Are the axis sensors on motors contactless ? (no potentiometer?)

What would the motor kit include? I have most of a printed propeler style gimbal but have it in piec

Similar Threads