YoshiroFR
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
Hey finally i had 4 faulty steppers
I made my own cfg
Atm i'm waiting for 4 new ones 10days delivery
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
Could someone send me his cfg for tmc5160 please?
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
It stay imo all my stepper are no operating
I dunno why...
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
What do you think about my cfg?
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
#[include]ratos.cfg
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
If i'm not wrong the configurator will overwrite this on next boot ?!
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
Should i should # include ratos.cfg is it correct?
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 3/11/2025 in #ratos-support
Mellow super 8 pro support
Mcu path
Motor pin ... dir pin... cie from printer.cfg
The ratos.cfg will not make conflict?
25 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
My bad i said bulls*it haha
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
I didn't build my own marlin firmware
I used wizard to do the job
But spi communication are not set initially...
Tmc2209 use uart....
Does klipper need spi communication allowed on the initial marlin firmware?
Or does it by itself?
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
2.1
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
I tried with another board octopus 1.1 ( no pro)
Same issue...
#spi_bus:
Should be called?
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
Up?
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
Did i miss something?
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
1: 4 jumpers on octopus are set (spi mode)
2: 2 jumpers on tmc for 64 step are set
3: tmc is on spi mode ( no jumper for this)
4: tmc5160t plus is set on wizzard
5: cfg check cs_pin dirpin
Sw mosi miso clk etc
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
Yes i think there is something i didn't done yet
21 replies
RRCRat Rig Community [Unofficial]
•Created by YoshiroFR on 2/28/2025 in #fix-my-printer
No spi communication
Yes tried all position exchange
21 replies