ArgueForSport Comments - Answer Overflow

ArgueForSport

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

You are a gentleman and a scholar! I indeed forgot to put that back in after I reflashed the image from the other issue. Thank you!!🙏

88 replies

RRCRat Rig Community [Unofficial]

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

I did add those lines. But I had to reimage the SD. Lemme make sure I added them back in

88 replies

RRCRat Rig Community [Unofficial]

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

Me, neither, lol.
When you are back and have a chance, your help will be much appreciated.

88 replies

RRCRat Rig Community [Unofficial]

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

Have you had a chance to think about configuring the Rat Pack?

88 replies

RRCRat Rig Community [Unofficial]

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

Still hoping someone will be able to chime in and let me know how / if to configure the Rat Pack to turn on. The instructions remain elusive for me. https://discord.com/channels/582187371529764864/1332848318539370577/1377851001108697218

88 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

Otherwise it will always try to use the built-in weak Pi Wi-Fi and won't even try to look for any other potential Wi-Fi sources

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

If I wasn't clear, the code in section 2B above disables the Pi's internal Wi-Fi. This allows an external USB Wi-Fi adapter to be recognized and used.

59 replies

RRCRat Rig Community [Unofficial]

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

Not that I saw. It is possible that I missed it? The configurator also says nothing about the Orbiter Smart Sensor, either. That ships with all of the VC4's and requires code to be added to the printer.cfg manually.

88 replies

RRCRat Rig Community [Unofficial]

•Created by abcurrie on 1/25/2025 in #ratos-support

Default Filter Fans Speeds don't meet Ratrig Docs

88 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

Thanks a million. The big piece that makes everything work is your sequence above from 5-13. And not to go into the Configurator at all until that sequence is completed. It would be great if this were documented somewhere (besides here of course!). Was able to successfully get through the configuration. The only difference I had was instead of step 2, because the Pi can't receive WiFi in my shop, I had to replace step #2 with these 2 steps: 2A. 100 foot Ethernet cable for initial connection to the Pi 2B. Connect external Wifi adapter - add "dtoverlay=disable-wifi" to the /boot/config.txt in the {ALL} section, then sudo reboot.

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

. Wish more thought had been given to where the Pi sits. in my case, I have to remove the right side panel of the eBox to remove/replace the SD card. Not super convenient.

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

I used Rufus and did not change any passwords, but I don't trust that I did everything correctly. It has too many options, to be honest, and more opportunities to mess up if you don't use it all the time. Going to reflash the SD with Balena 1.18. Simple. Works for me

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

That would be a me problem, not a Rufus problem, lol

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

I'm gonna redo it with 1.18 because I don't really know if Rufus did it right

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

merci beacoup

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

I originally imaged the SD with Balena Etcher 1.19.21. Last night I remembered the Etcher version issue AFTER I imaged it, connected the 100 foot long Etherweb cable, and got external WiFi configured. 1.19.21 may have caused the RatOS configurator issue in the first place.
This git issue shows the same Mainsail errors @Grape and I both experienced. The Etcher version might have been the cause, at least in my case. https://github.com/Rat-OS/RatOS/issues/178 I thought 1.18.4 and earlier were ok. I used that version last year to install mainline Klipper on my QIDI because they had the same issues with Balena. What's versions of Etcher are known good for writing the RatOS image onto the SD?

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error

Didn't want to rip this all out!

59 replies

RRCRat Rig Community [Unofficial]

•Created by Grape on 5/15/2025 in #ratos-support

Ratos configurator 502 gateway error