Raven 3D Tech
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/13/2025 in #fix-my-printer
_BEACON_APPLY_RUNTIME_MULTIPLIER
I fixed the problem by adding to the RatOS variable in the printer.cfg this:
variable_beacon_contact_expansion_compensation: False
3 replies
RRCRat Rig Community [Unofficial]
•Created by jvs 3d on 12/16/2024 in #ratos-support
After a update this error occur:
Has this been solved? I ran into the same issue today with IDEX 500.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
@Mitsuma Thanks you very much my friend
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
I just was asuming since it says in the documentation it don't matter the cabling aslong you use the motors and cable that it comes wiht it.
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
You are a live saver. Works 100%
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
anyway I wil lcheck it now
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
Is wear s it was created by the configurator.
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
OK. I will chake that in a minute.
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 4/11/2025 in #fix-my-printer
Rat Rig 500 Hybrid Y-Axis jumping and loud noise
You Mean the actuall stepper drivers or motors?
18 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 3/31/2025 in #fix-my-printer
VAOC IDEX Calibration toolhead collision.
@Budz (PD3D) @Martin Hanbury All is sorted out. Wrong part cooling mounted. Speed: I have not figured it out yet, but I will get there.
6 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 3/31/2025 in #fix-my-printer
VAOC IDEX Calibration toolhead collision.
OK. I sorted it out. Looks like it doesn't like to have Kraken motors running at 1.6 amp. Once it is lowered to 1.1, all works fine.
6 replies
RRCRat Rig Community [Unofficial]
•Created by TheFullNelson32 on 2/24/2025 in #ratos-support
Trying to flash Ebb 42 Can 1.2 but it will not go into DFU mode for flashing? any suggestions?
I have run into the same problem and no matter what I do it will not go into DFU mode. I have not been able to trouble shoot it as I'm in holiday and will be back in 3 to 4 weeks.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/28/2025 in #ratos-support
Rat Pack wont start
Yep. That did the trick.. If I would read more I could have figure it out. Thank you
7 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/28/2025 in #ratos-support
Rat Pack wont start
Yes. Still not working
7 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/5/2025 in #fix-my-printer
Z-Tilt is only adjusting one Axis.
OK. I changed the cables around as you suggested. Now, my Z1 is in the front left, Z0 is in the back, and Z2 remains in the front right. It makes no sense, but it is working now. I mark this now as closed. Thanks for your Help. @Helge Keck
24 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/5/2025 in #fix-my-printer
Z-Tilt is only adjusting one Axis.
Is like is executing it twice.
24 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/5/2025 in #fix-my-printer
Z-Tilt is only adjusting one Axis.
What would make it in the 2nd run to swap?
24 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/5/2025 in #fix-my-printer
Z-Tilt is only adjusting one Axis.
will mesure more inside
24 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/5/2025 in #fix-my-printer
Z-Tilt is only adjusting one Axis.
I checked the couplers and their OK
24 replies
RRCRat Rig Community [Unofficial]
•Created by Raven 3D Tech on 1/5/2025 in #fix-my-printer
Z-Tilt is only adjusting one Axis.
OK. I can do that.
24 replies