t8k3n
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
I set the printer profile up as core xy instead of hybrid. I had to move the motor cables to match the core xy diagram on the octopus and z-tilt worked the first time. Either the hybrid belt has to be installed (which doesn't make much since to me because the toolhead was moving in the y direction without it or something is not right with the wiring diagram(I think I tried every combination so not convinced on this either) or the hybrid config when using it on a 3.1 build. I had to flip the left and right motors on the octopus to get homing to work. I think this is what may have been causing issues with the z-tilt not working. For now I just want to see this thing print so I'm leaving it here and continuing on with the setup. Thanks for all the suggestions
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
No luck, I tried each combination but ended up with the same errors.
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
Eternal, I verified that according to the build manual, that they are correct. Does your motors not match the build manual ? I'll give it a shot though, thanks for the idea
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
Yes homing works perfect
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
I can manually adjust to the point that it drops the front or the back but never does it try raising a corner. Even when I start it with the front noticeably lower it still drops the front when running the z-tilt. To the point that the sensor cannot see the bed then errors.
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
I have to have something backwards when it comes to z-tilt but I sure can't figure out what it is.
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
which should be 6,7,8
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
I have it wired according to that picture
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
or step 55 rather
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
page 55
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
Z2 is the front right but I think that is what they meant?
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
1:07 PM
stepper_buzz stepper=stepper_z2
1:06 PM
stepper_buzz stepper=stepper_z1
1:06 PM
stepper_buzz stepper=stepper_z
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
running these commands matched that doc:
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
The Z0 Stepper must be connecter to driver 5.
Z0 is the front left stepper, when looking at the machine from the front.
The Z1 Stepper must be connecter to driver 6.
Z1 is the rear stepper, when looking at the machine from the front.
The Z2 Stepper must be connecter to driver 7.
Z2 is the rear stepper, when looking at the machine from the front.
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
Is this part of the documentation correct?
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
I did do the buzz test in the beginning so I don't think so. How do I move the start point in a bit instead of probing the edge of the bed? do I increase the endstop position?
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
It will be a 3.1 hybrid though eventually
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
The probe is stopping over the bed though
71 replies
RRCRat Rig Community [Unofficial]
•Created by t8k3n on 5/17/2025 in #ratos-support
Z-tilt configuration
This one isn't a beacon, still old school
71 replies