MDFPereira
RRCRat Rig Community [Unofficial]
•Created by Nightrider on 2/9/2025 in #ratos-support
Configurate an unsupported Printer
This is why RatOS clearly states what printers are supported
6 replies
RRCRat Rig Community [Unofficial]
•Created by Nightrider on 2/9/2025 in #ratos-support
Configurate an unsupported Printer
Honestly, none.
You hace CoreXY, Octopus, Dragon HF and LGX Lite.
Even then, temp sensor may not be the same, bltouch offsets may not be the same, stock motors are not included, etc.
6 replies
RRCRat Rig Community [Unofficial]
•Created by venki on 2/8/2025 in #ratos-support
ratos in mini pc
The production machines uses Rpi 4. Don’t you think it is enough? 😉
12 replies
RRCRat Rig Community [Unofficial]
•Created by venki on 2/8/2025 in #ratos-support
ratos in mini pc
Less risky of you are not familiar
12 replies
RRCRat Rig Community [Unofficial]
•Created by venki on 2/8/2025 in #ratos-support
ratos in mini pc
Pi is ready to use…
12 replies
RRCRat Rig Community [Unofficial]
•Created by venki on 2/8/2025 in #ratos-support
ratos in mini pc
If you manage to install Raspbery pi OS on the PC, yes, it can run RatOS.
But is a bit of a pain to install everything command by command
12 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/7/2025 in #fix-my-printer
VAOC Cam freezing
Having it also setup as a webcam may cause issues if the device is already in use
17 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/7/2025 in #fix-my-printer
VAOC Cam freezing
And remove the VAOC cam from webcams.
17 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/7/2025 in #fix-my-printer
VAOC Cam freezing

17 replies
RRCRat Rig Community [Unofficial]
•Created by AOne on 2/7/2025 in #fix-my-printer
VAOC Cam freezing
Check your crowsnest config
17 replies
RRCRat Rig Community [Unofficial]
•Created by tiggo256 on 2/7/2025 in #fix-my-printer
Bent Lead screw
did you sent any email?
3 replies
RRCRat Rig Community [Unofficial]
•Created by kf9j on 2/1/2025 in #ratos-support
v-chonk: does not return to xy safe-home location before homing z
did you try to home via the buttons instead of sending the G28 x?
22 replies
RRCRat Rig Community [Unofficial]
•Created by kf9j on 2/1/2025 in #ratos-support
v-chonk: does not return to xy safe-home location before homing z
if you set home_xy_position to 0,90 and it homes in the middle, something is wrong
22 replies
RRCRat Rig Community [Unofficial]
•Created by kf9j on 2/1/2025 in #ratos-support
v-chonk: does not return to xy safe-home location before homing z
It is homing Z in the centre?
22 replies
RRCRat Rig Community [Unofficial]
•Created by Qui1zy on 2/6/2025 in #ratos-support
Ratos Invalid
i suggest saving the config files and burn a new image
32 replies
RRCRat Rig Community [Unofficial]
•Created by Qui1zy on 2/6/2025 in #ratos-support
Ratos Invalid
it should work
32 replies
RRCRat Rig Community [Unofficial]
•Created by Qui1zy on 2/6/2025 in #ratos-support
Ratos Invalid
something very messed up
32 replies
RRCRat Rig Community [Unofficial]
•Created by Qui1zy on 2/6/2025 in #ratos-support
Ratos Invalid

32 replies
RRCRat Rig Community [Unofficial]
•Created by Qui1zy on 2/6/2025 in #ratos-support
Ratos Invalid
if not, send this
sudo systemctl status ratos-configurator
32 replies
RRCRat Rig Community [Unofficial]
•Created by Qui1zy on 2/6/2025 in #ratos-support
Ratos Invalid
line by line
32 replies