MDW Magbed Mesh
Anyone know how to setup faulty regions? I have messinga round for the past week but can't figure it out. I entered the below info the printer.cfg to test out the first spike, but klipper crashes after the scan completes. Appreciate the help!
[bed_mesh] #exclude zones for magnets
speed: 120
horizontal_move_z: 5...
V-core 4 500 High bow Infront
Hello guys,
Quite new to building a 3d printer my first time actually hahaha. I was wondering what is causing the bend upwards at the front of my bed mesh. Would someone be so kind to walk me through what is happening and if i can adjust it further.
Many thanks in advance...
V-Core 4 - 300 - What is an acceptable range?
Hello guys, currently preparing my V-Core 4 - 300 and I'm stuck at the bed mesh. In general no big topic but I need some advises from you.
1. What is an acceptable range for a 300 mm bed?
2. I'm fighting a bit with the lower dip in the mesh. Do I have to unscrew the Back Panel as well move it further down?
3. I have those waves in the bed. Are my Y-rails screwed too tight or from what does this com?...
Commissioning Mesh - race to the top
I am working on meshing my cold bed before putting the heater on it, and I seem to be racing to the top with my left and right front corners.
When i start, I am pretty much on the same plane with A,B, and D corners (FL, FR, BL) as well as rear middle probe point, with the C (BR) corner off by anywhere from -.4 to -.7.
If I make even a slight adjustment to the B corner to bring it up a tad, then then next mesh shows, the D corner off by -.4 to -.7. And I just seem to keep racing to bring both corner up and up and up....
If I make even a slight adjustment to the B corner to bring it up a tad, then then next mesh shows, the D corner off by -.4 to -.7. And I just seem to keep racing to bring both corner up and up and up....
Leveling a warped Bed Mesh Vcore4 500mm
Hi, I am new to Ratrig machines and I am trying to remove the warp from my gantry following the manual and tips I found here. I have moved feet up and down to get as close as I could and then I loosened the fasteners on the gantry and tweaked it until I got to this mesh, my best so far. I started from a 1.3mm deviation. My brother assembled the frame and I was not there. Do I need to disasemble and reasemble or is there more I can tweak first?
can/should I try to improve this with kapton tape?
Since replacing the Eva 3 with the RR Toolhead and using a beacon probe, I find that the z offset is tuned well for the center of my bed but closer to the edges it doesn't stick. In particular, I noticed this when attempting to do an EM calibration (with the 9 blocks) for a new filament. I thought maybe I could improve my mesh with a little bit of kapton tape. Good idea? Bad idea? (with the 9 blocks).
Vcore 3.1 400 after beacon configuration
Z-tilt done several times yet the bed mesh looks like Z1 is off by 1mm. BEACON_CREATE_SCAN_COMPENSATION_MESH created the contact bed mesh profile which looks identical. I rotated the build plate by 90 deg and it's still the same (pictured). I verified the stepper motors via buzz as well.
2 level mesh V-Core 4 - 400 - IDEX
Dears,
I am puzzled from this bed mesh on a V-Core 4 400 IDEX.
I don't know where to start because of this odd shape, on the Y axis I think... I found no similar references....
Vcore 4 IDEX 500mm bed banana...
Just finally got my printer together, imo it was all square when building. Was built on a glass table and measured corner to corner where possible. I've done everything up to BEACON_RATOS_CALIBRATE then scanned the bed.
I see a lot of people with a similar problem but this seemed like the worst. Not sure what to do 😦...
V-core 4 500
I've watched the video several times but this is best I can get. Is .392 okay for a 500?
Fixing the hump - VC4 - 400
I recently rebuild my printer, relocation and all that and for the love of me I can't remember how to fix the horizontal hump. The narrow vertical dip is a toro tube issue, that i need to hamer out (literally). But the Horizontal wave is bugging me.
4 corner peaks obvious dip in middle - what to do
Any idea mhat my best course of action is for this concave mesh?
Low dip on D
Hi guys any advice on how to tackle the back left D point. have been trying to pull it down and tap it with a rubber hammer. but so far it wont improve much.
V-core 4 500
Thank you in advance...
Brand new bed - flatnes problem
I received a brand new V-core 3.1 400mm bed yesterday from RatRig
But I have doubts about its flatness - what do you think whether this is grounds for a complaint??
I can honestly say that my previous bed has a 0.340 difference...
Strange Heightmap Shape
Hi guys,
I have V-Core 4.0 with IDEX and my heightmap looks like this. Is this an acceptable result? If not, what do I need to change here?
Thanks in advance....
Solution:
I have yanked my gantry down a couple of times and this is the result now. What do you think?
Need Help with Commissioning Mesh VC4 500
Here's what I have after a few adjustments to the frame and retorquing the x and y rails. I also reduced the number of bolts on the y rails from 12 to 8. The range in the y axis has not change with all the adjustments I have done, which leads me to believe the bed is bent that way. I do not have a precision straight edge to check the straightness of the bed.
Are there any further adjustments I should make before possibly getting a new bed or should I live with 0.566 of range?...
Are there any further adjustments I should make before possibly getting a new bed or should I live with 0.566 of range?...
