Yeah. It Probably would be best to replace the grub screws with new ones. I could mail you some, b

Yeah.

It Probably would be best to replace the grub screws with new ones. I could mail you some, but if you're able to find some on your end would be faster

Wwalmis Yeah. It Probably would be best to replace the grub screws with new ones. I co...

PiNKSH!T•5/3/23, 1:07 PM

yeah awesome m8 thanks for the offer, I'll check out local supply shouldn't be too hard, def going to smash it with lock-tite though!

Fer•5/3/23, 4:54 PM

Hey @walmis how do you put in the code the trim feature for harrier ? And how do I use the trim with msfs?

TTC-Durham With a lot of messing around with my virpil 200mm extension, I got it to send a ...

Number481•5/3/23, 5:55 PM

@.durham - Were you able to resolve this? Having more or less the same issue with my Alpha + 200cm extension. If the trigger flip lever is forward (button 1 should be activated), button 1 shows solid lit in configurator but one of the hat switch indicators is continuously flashing, if the lever is retracted (button 2 should be activated), Button 1 flashes continuously. I also seem to be getting a lot of crosstalk or something on the hat switches. Some hat presses seem to control a directional push on a different hat, or a button press in stead of a hat press.. all very strange.

All seems to work just fine without the extension. (note I've been using this extension with my CM2 and then CM3 bases for over a year with no issues.

NNumber481 @.durham - Were you able to resolve this? Having more or less the same issue ...

walmisOP•5/3/23, 6:17 PM

That's very strange. I have tested my Alpha with a 2 meter cable, all works normally. Maybe Virpil has different hardware revisions inside the grip which is more sensitive to cross talk.
One hardware mod to try would be to add a 100 or 330ohm resistor on the SPI data line in series.
Otherwise I'd be happy to help diagnose this via remote desktop, maybe a firmware based fix would be possible.

FFer Hey @walmis how do you put in the code the trim feature for harrier ? And how do...

walmisOP•5/3/23, 6:22 PM

The current wip development branch is a bit unfinished for general usage at the moment, still a lot to do for MSFS support.

TC-Durham•5/3/23, 6:26 PM

@Number481 - I got button 1 to stable red after taking the extension apart and putting duct tape on the exposed wires at the top of the join of the two cables that make up the connection inside the extension. I could not find what button 1 actually did, so renamed it button 0 to stop it dominating the DCS controls setup and off I went. I did try my VPC F-14 (V.F.X.) grip and got lots of red buttons and some flickering, so just went back to the VPC Mongoose T-50CM2 that I use for the Apache. The issue was definitely the extension as the behaviour was different and better when just screwing the grip onto the Rhino mount and even when using the straight tubular extensions. I have another 200mm extension on order to see if that behaves any differently.

TC-Durham•5/3/23, 6:29 PM

It seems to be something to do with how much you have to compress the cable inside the extension which is necessary for pulling out the male connector at the bottom so you can get your fingers in to plug it on, and then it smoothly goes back inside as you screw down the bottom of the extension - ie I also got much better behaviour with the extension in pieces and using the cable with no kinks, bends or other compression.

TTC-Durham It seems to be something to do with how much you have to compress the cable insi...

Number481•5/3/23, 6:30 PM

Yeah, I just took mine apart to see whats what.. uncoiling the cable from inside the extension doesn't seem to help my case. FYI, button 1 is (should be) always active if the flip trigger is forward, button 2 is always active if the flip trigger is pulled back (at least on the Alpha).

Wwalmis That's very strange. I have tested my Alpha with a 2 meter cable, all works norm...

Number481•5/3/23, 6:32 PM

Is that one of the data lines on the extension connector? I don't have any resistors lying around but could probably have some by tomorrow. It's actually the Alpha Prime, but I think thats mostly just RGB and construction differences to the original Alpha.

walmisOP•5/3/23, 6:33 PM

I'll send you some pinout diagrams tomorrow morning once I get back to work

Wwalmis The current wip development branch is a bit unfinished for general usage at the...

Fer•5/3/23, 6:36 PM

And for harrier trim?

NNumber481 Yeah, I just took mine apart to see whats what.. uncoiling the cable from inside...

TC-Durham•5/3/23, 7:28 PM

Have you got the straight extensions?

TC-Durham•5/3/23, 7:28 PM

With the one piece cable?

Number481•5/3/23, 7:36 PM

no, its the offset extension.

Number481•5/3/23, 7:37 PM

took it apart, removed the shrink wrap.. reseated the connector joining the two halves of the cable.. issue persists.

TC-Durham•5/3/23, 7:39 PM

And that is even when the cable is straightened out?

TC-Durham•5/3/23, 7:40 PM

I have the offset extension, which is the one that gave me the issues - the cable in the picture above played nice.

Number481•5/3/23, 8:07 PM

Yeah I assume it has something to do with the way they’ve connected the two halves together causing crosstalk of some sort.

Number481•5/3/23, 8:08 PM

Number481•5/3/23, 8:09 PM

@walmis would you suggest trying to directly solder the two halves together and remove the connectors?

TC-Durham•5/3/23, 8:11 PM

That was my conclusion - and when you cram it all together the potential for crosstalk increases

Number481•5/3/23, 9:47 PM

Well, I cut the connectors out and direct soldered the cable.. ~~problem is (mostly) gone.. I do still see occasional flash of button 1 in configurator so I assume there's still some crosstalk going on.~~ Well.. spoke too soon. shoved it all back inside the tube and the crosstalk is back :/

Number481•5/3/23, 9:47 PM

HereComesWhitey•5/3/23, 10:21 PM

Maybe using coax cables would work?

Number481•5/3/23, 11:53 PM

@walmis after failing to fix the issue by removing the connectors and directly soldering the wires, but noticing that when it wasn't coiled inside the tube the issue was lessened or non existent, I cut about 12cm out of the cable and soldered it back up so that it wasn't so coiled up when pushed back into the extension tube. Seems to be working so far...

Number481•5/3/23, 11:53 PM

NNumber481 Click to see attachment

Jehly•5/4/23, 12:30 AM

Sorry, where'd you get that switch hat on the top right??

JJehly Sorry, where'd you get that switch hat on the top right??

Number481•5/4/23, 12:39 AM

designed and 3d printed it because I needed a china hat

NNumber481 designed and 3d printed it because I needed a china hat 🙂

Jehly•5/4/23, 12:48 AM

Color me impressed and jealous.

JJehly Color me impressed and jealous.

Number481•5/4/23, 12:52 AM

you're welcome to the file

NNumber481 you're welcome to the file

Jehly•5/4/23, 12:55 AM

I’d love that! Do you just pop it off?

Number481•5/4/23, 12:58 AM

yeah, the default ones are just pressure fit on a metal spline (this is the alpha prime, I assume the alpha is similar). Takes a bit of force to get them off. I moved the one that's on the upper right by default to the lower left and then put the printed china hat in the upper right

JJehly I’d love that! Do you just pop it off?

Number481•5/4/23, 1:02 AM

DM'd

Jehly•5/4/23, 1:03 AM

Thanks!

Jon (Bounty_V)•5/4/23, 11:36 AM

Rhino owners! Looking to get 1 or more throw limiters with my Rhino, and I'm a complete novice when it comes to this sort of thing and have no clue what throw angles I should be considering. What is everyone's experience with throw limiters an what sizes have been good for you all? Any specific modules you use the limiter for?

Vulcan•5/4/23, 12:10 PM

Best to get a protractor out, put it where the base goes and eyeball the obstructions in your pit. Half throw is about 10.5 degrees and that's what im rocking due to an extension since I bolt the base to the bottom of my simpit

Vulcan•5/4/23, 12:11 PM

Jon (Bounty_V)•5/4/23, 12:14 PM

Yeah not a bad call. I'm trying to figure it out before I get the base as part of the order form which does slightly complicate things

So you would say the specs saying 44 degrees on both x and y is 22x and 22y not 44x and 44y?

Vulcan•5/4/23, 12:16 PM

Yes 21 or 22

Vulcan•5/4/23, 12:21 PM

You'll probably need a few throw limiters to get close to what you want if you're going in blind. If you have a really long extension like 200mm, consider taking a drastic amount off like I did. If it's a lot shorter then maybe only 75-80%

Jon (Bounty_V)•5/4/23, 12:43 PM

Ok I was able to determine I will want a 200mm extension. So I think I will get a 50% limiter. I'll also get a 75% limiter should I want to change to 100mm.

VVulcan Best to get a protractor out, put it where the base goes and eyeball the obstruc...

ddrake1984•5/4/23, 1:17 PM

that's exactly how I have mine mounted

ddrake1984•5/4/23, 1:17 PM

JJon (Bounty_V)Ok I was able to determine I will want a 200mm extension. So I think I will get ...

Vulcan•5/4/23, 1:28 PM

That sounds like a good starting point, if the throw isn't enough for your personal preference with the 50% try the 75% and if that's too much get another one later somewhere in the middle

zbyte•5/4/23, 5:19 PM

Apologies for my ignorance but trying to understand the subject, the throw limiter will restrict the arc length movement of the stick to avoid hitting other objects during usage, the standard angle per axis (angular displacement) without limiter is 44 degrees give or take, with a 200mm extension (close to radius value since some distance from pivot is not accounted by the extension), you limit this 44 to 22 degrees give or take and with a 100mm extension you could "assume" roughly 33 degrees. The Rhino then will be calibrated to whichever max allowed throw is at its max value and will operate accordingly. Questions, is my statement accurate? Is the Rhino adjustment linear or follows other function like logarithmic or exponential or else? Thank you.

amadeus•5/4/23, 5:52 PM

When you calibrate the rhino you basically tell the firmware it the minimum and maximum distance of physical travel for each axis, so then it maps that to what it reports to windows/games as -100% to 100%, (technically it’s reported as an integer value, like -4986 to 4986 I think?) but yeah linear travel along those value ranges, no curves are anything are added if you limit the throw

PiNKSH!T•5/5/23, 6:05 AM

@walmis Hey m8, I've got replacement grub screws but one of the ones in the gear won't come out, their way too shallow. I'm going to try & superglue the alan key to the top of the grub screw, if that doesn't work what am I supposed to do?

PPiNKSH!T @walmis Hey m8, I've got replacement grub screws but one of the ones in the gear...

walmisOP•5/5/23, 6:09 AM

I usually use a hex screwdriver so I can get a good pressure on the screw to get it out, the L shaped allen key might be difficult to use

walmisOP•5/5/23, 6:10 AM

a dab of wd40 might help also

walmisOP•5/5/23, 6:11 AM

also you might try tightening the other one with a new grub screw, might be enough

Yeah. It Probably would be best to replace the grub screws with new ones. I could mail you some, b

Similar Threads