Ait has an incredibly dumb controller interface, I've literally never before seen a game that has controls bindable and perfectly functional in the setup menu but don't show up in-game at all - but that's just one of the Il-2 quirks. Usually the right move is to reduce the number of active controllers to bare minimum.
TYeah at this moment I'm chalking it up to IL-2 being IL-2, that controller interface is pretty garbage ngl, they certainly could have done a much better job with that, and people on the forums have been telling them as much.
LI have also had trouble getting IL-2 actually use the controls in the game even though they work when I set them up. Strange as it may seem, being in VR or pancake affects it too. Recommendation is to never bind controls in VR (which I would prefer to do) but switch to pancake. Then they work in VR .
LController support in IL-2 is awry.
Lwhat does Trim Release Button do?
NIts part of the hardware force trim implementation. Pushing trim release button will remove spring forces until the button is released. Where you release the button, the new "center" of the spring forces will be where you released it
Looh thats cool
Nmostly for emulating helicopter force trim if a simulator doesn't support it natively
LIs there a way to "lock" trim so it only works on the pitch axis? This would simulate glider trim correctly (LS4 for example)
Nnot in configurator that I know of. I did write a force-trim implementation for helicopters in TelemFFB for MSFS that works the same way. If you describe how the system works on a glider it could probably be done in TelemFFB.
LOn most gliders you have a sort of pedal behind the stick, which moves the spring center to the position to the current stick position
LThe Green grip behind the main stick
MYou could do the trim setting you want easily. Simply only bind controls for motorized trim for your pitch. Don’t do roll.
MOr is there more to it
Nso its like a physical disconnect from the spring system? Is it a "pull-and-hold" action on the lever until you get the stick where you want?
Ndifferent from standard trim controls.. this behaves more like a helicopter force-trim system
LKind of, I think i can record a video for you tomorrow
LThis is a different glider type, the difference is, that on this one you move a trim lever. To do that on the LS4 you pull the trim lever and then the trim moves to the stick position and stays there when you release it.
LYou have to ignore that the trim lever moves a bit with the stick, that is because it wasnt tighted properly in this clip
Ninteresting.. I think the best we could approximate in TelemFFB is a button binding (could use the paddle on grip) that removes only the elevator spring force and re-centers it when released.
JWhat would this cable be called (specs), so I can get a replacement. The Y axis stopped working suddenly for no reason. First thing that crossed my mind that it would be a loose connector, so I opened up the stick, but all was seated. With fiddeling at the cable, the motor came alive. So I placed it that it works, closed the stick up and went flying. Net though, it won't stay for long, so I better get me a spare.
SYea, those connectors are fragile.
Get yourself this kit...
https://www.amazon.com/gp/product/B08T89ZK2Q/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Get yourself this kit...
https://www.amazon.com/gp/product/B08T89ZK2Q/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
PH 2.0 Connector Pre-Crimped Cable Kit Compatible with JST-PH 2.0mm for Battery JJRC H36 Blade Inductrix Tiny Whoop Arduino mkr1010 MKR Zero and MKR Vidor 4000 (Female&Male Connector&Wire)
HI know this is a very belated response, but I've been busy moving into a new house and job, so I've not had time to mess around with this.
I finally pulled the port out and took a look, and I don't see any obvious issues or damage, but the stick is recognized when I plug it in with the port removed, so I can only assume it was an issue with the solder points on the port that's not visible (maybe a cold joint?)
I finally pulled the port out and took a look, and I don't see any obvious issues or damage, but the stick is recognized when I plug it in with the port removed, so I can only assume it was an issue with the solder points on the port that's not visible (maybe a cold joint?)
HI'll put it back together and if needed, I'll resolder the connections and see if that fixes the issue.
JIf you disconnect the USB while loaded into DCS. Is there a way to have DCS find the Rhino again? Rescan devices didn't work.
DTrim function doesn't seem to work, doesn't move with assigned buttons, but will move with a non-assigned button.
WHardware trim? If so do you have the latest .16-1 configurator version?
GWhat about activating Enable Hotplug, the button next to the rescan devices you mention from Keybinding screen? Sometimes when I loose the ffb in DCS I just have to re-slot.
G
JI didn't try to reslot. I'll try that thanks.
N@walmis - Are the kits on waiting lists or just the full base? Do the USB electronics encode the stick positions or are separate sensors needed? I saw there are some potentiometer inputs - trim or control inputs? Are those compatible with Hall effect sensors too if they are control inputs? Looks like a really great sim accessory!
WThe kits don't have a waiting list and are quick to ship. Motors act like stick position sensors, so no additional sensors are needed. The pot inputs have various functions assignable via UI and can be axis control inputs. Hall sensor 0-3.3V will work too.
NThank you, @walmis! Are the middle size motors enough to stand up a full length stick? Just PVC with a Warthog grip on it about 2 feet long.
FIs there a way to correct for crosstalk for certain gimbal designs?
N@walmis - sent you a PM about my order…
SHi! Just recieved mine - super impressed with build quality. However, when I try to update firmware via https://vpforcecontrols.com/usb/rhino/ I get an error: "Error: NetworkError: Failed to execute 'claimInterface' on 'USBDevice': Unable to claim interface." Any ideas anyone? Googling doesn't make me wiser...
DI think it's an error on their end, mine is also doing the same.
SAh, ok... We'll have to wait for a fix then...
PAnyone able to use force trim with UH60 dcs mod? Can’t get it to hold new stick position when trimming
PFound answer, using hardware trim in the config tool
Ahttps://canary.discord.com/channels/965234441511383080/968208779084701716/1151153966483243030 here's the fix to the
unable to claim interfaceProbably the stupidest question yet, but I'm currently playing FS22, using twin stick for crane controls. But the Rhino doesn't work there, if I put it on raising/lowering the crane with Y+ and Y- respectively, all it does is raise Y+ even if I don't physically manipulate the stick?
BI flew that 'hawk once, and put it aside. To me the flight model is.... Lacking. Severely so. Hopefully it will improve.
VWhat is the diameter of vkb adapter metal part?
SYour Google-fu is strong, oh great @amadeus ! I thank you a thousand times, that worked!
ANpnp! I just spend too much time in this server 
LWhat is suitable resistance to potentiometers? And which ratio is in a rhinos timing pulleys?
V1:6.2 ratio belt drive
from manual https://discord.com/channels/965234441511383080/1091401951951982602
from manual https://discord.com/channels/965234441511383080/1091401951951982602
BI just got done flying the excellent freeware A-29B for DCS (https://github.com/luizrenault/a-29b-community). I have an entry for it in the TelemFFB user config file if that matters... I just looked at the log after completing a flight, and there are mulitiple "simconnect?" messages interspersed with DCS effects -- e.g.:
2023-09-26 10:54:14.881 - INFO - Destroying effect 9 (Sine) ("prop_rpm0-2")
2023-09-26 10:54:14.882 - INFO - Destroying effect 10 (Sine) ("prop_rpm1-1")
2023-09-26 10:54:14.883 - INFO - Destroying effect 11 (Sine) ("prop_rpm1-2")
2023-09-26 10:54:23.339 - INFO - Trying SimConnect
2023-09-26 10:54:23.743 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:33.743 - INFO - Trying SimConnect
2023-09-26 10:54:34.146 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:44.146 - INFO - Trying SimConnect
2023-09-26 10:54:44.550 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:54.551 - INFO - Trying SimConnect
2023-09-26 10:54:54.954 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:58.72 - INFO - Telemetry Timeout, stopping effects
2023-09-26 10:54:58.72 - INFO - Stop effect 12 (Constant) ("aoa")
2023-09-26 10:54:58.73 - INFO - Stop effect 14 (Constant) ("runway0")
2023-09-26 10:54:58.74 - INFO - Stop effect 15 (Constant) ("runway1")
2023-09-26 10:54:58.75 - INFO - Stop effect 17 (Constant) ("elev_droop")
2023-09-26 10:55:04.956 - INFO - Trying SimConnect
2023-09-26 10:55:05.359 - ERROR - Failed to open SimConnect, is Flight Simulator running?
Shouldn't the app stop looking for MSFS when DCS is active? This doesn't seem to hurt anything but it seems inefficient to my noob programmer wannabe self...
2023-09-26 10:54:14.881 - INFO - Destroying effect 9 (Sine) ("prop_rpm0-2")
2023-09-26 10:54:14.882 - INFO - Destroying effect 10 (Sine) ("prop_rpm1-1")
2023-09-26 10:54:14.883 - INFO - Destroying effect 11 (Sine) ("prop_rpm1-2")
2023-09-26 10:54:23.339 - INFO - Trying SimConnect
2023-09-26 10:54:23.743 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:33.743 - INFO - Trying SimConnect
2023-09-26 10:54:34.146 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:44.146 - INFO - Trying SimConnect
2023-09-26 10:54:44.550 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:54.551 - INFO - Trying SimConnect
2023-09-26 10:54:54.954 - ERROR - Failed to open SimConnect, is Flight Simulator running?
2023-09-26 10:54:58.72 - INFO - Telemetry Timeout, stopping effects
2023-09-26 10:54:58.72 - INFO - Stop effect 12 (Constant) ("aoa")
2023-09-26 10:54:58.73 - INFO - Stop effect 14 (Constant) ("runway0")
2023-09-26 10:54:58.74 - INFO - Stop effect 15 (Constant) ("runway1")
2023-09-26 10:54:58.75 - INFO - Stop effect 17 (Constant) ("elev_droop")
2023-09-26 10:55:04.956 - INFO - Trying SimConnect
2023-09-26 10:55:05.359 - ERROR - Failed to open SimConnect, is Flight Simulator running?
Shouldn't the app stop looking for MSFS when DCS is active? This doesn't seem to hurt anything but it seems inefficient to my noob programmer wannabe self...
NNo.. its like the little engine that could.. it never stops waiting for a connect event from MSFS if it is enabled in the config